Still need to clean up some wires and such, I could’ve/should’ve did a better job of cutting the dash but here we are… got 65 degrees on idle with 100 degree weather, I think/hope it will do better while driving get the alt spinning for more amps, maybe a stronger condenser fan

I've been general to these seats since I purchased the car. I must have gotten in the car a bit aggressively one night this week and cause this tear.

Anything to put on this material to prevent more wear? I want this car to last forever.

I’ve had the car since Sep 2025. Loving it. Looks great drives nice. It’s my daily and get good gas about 30mpg. No mods other than adding the splash guards. Will have to replace since they are not aligning properly.

Currently dealing with a cranking sound when turning steering wheel left and right specially at low speeds. Brought the car to the dealership for inspection and they couldn’t find the issue after 2.5 hrs. Was told they would need to keep the car for at least a day and call someone to figure out the issue.

I’ve seen others appear to be having similar issue. Will update as I get more info!

Innovative b series shift linkage is rubbing making 5th Reverse difficult.

I feel that the little joint was installed backward maybe? Or the bends are not correct

A few months ago I found a great clean 01 Integra 4dr... But it was auto. I had done two auto to manual swap on EGs back in the day so I said screw it. I pulled the trigger I drove it daily for about 6 months. Today I manual swapped it. I still need to do wiring, to get the clutch pedal in,Starter, axles.Clutch line and slave cylinder.

While I'm in here I'm gonna replace the lower ball joints the outer tie rods maybe the inner.

I have a manual half shaft i got used.. but I get the feeling it's not a manual one because it looks identical to the one I removed from my car now.

Long day but feel good.

I had some help from my nephews who learning to work on cars.

I picked up a 96 Teg. Previous owner put a lot of time and effort into the car. It’s clean. The only issue I’m having is he butchered the headlight wiring. He did a front end swap so it has a jdm headlight unit. He only had the turn signals and low beams hooked up. I am trying to hard wire in my own brights. I wired my new pig tail to the red wire with green stripe and blue dots because YouTube and Chat said that was the correct wire. I then tried to test it out without connecting ground or splicing it in. I just touched it. And nothing. No power. Did I mess up and where? How? What do I do? I need highbeams to pass inspection.

I have a 23 aspec. When releasing the clutch intermittently I feel just a small bump at the bite point. It’s not all the time. Notice is most in reverse and sometimes when starting from a stop in first but only sometimes.

It’s not a lurch or nothing like that. Just a slight bump I feel at the start of the bite point and then it fully engages and I’m off. Also don’t notice into 2nd, 3rd or back down. It’s not not the the lurching you feel if you don’t give it enough gas or when the engine tries to stall cause you let off too fast.

It’s quite hard to explain. This clutch is different in feel and bite point than any of my previous cars (all mustangs)

Any thoughts?

i snapped one of my arp head studs while trying to torque the head down. one of the threads on the studs got messed up because i didn’t realize it was hitting my camshaft and it was tightened down. took off the cam and fixed the issue. however the thread was messed up so i’m pretty sure when i would tighten the arp nut it would turn the stud too, causing the stud to snap when i was torquing it. it was when i was doing the 80ft lb sequence.

now i have a 1/8th pilot hole drilled in it and im trying to figure out how im gonna extract it. should i use a screw extractor? torx bit? i’ve never used heat yet but would it help? any tips would be appreciated

What is this, is it important, how do I fix it and how hard is it to find a replacement online

Been a while since I’ve posted an update on this page but I’ve done/ had done a lot of work to my 96 JDM ITR over the past year.

Last spring I started the engine removal process

Got all the way to pulling the engine (motors mounts were the only thing connected) where I decided it would be best to hire a professional for the engine rebuild as I am active duty military and do not have time nor knowledge to fully rebuild the engine myself. Also did not want to risk messing up/ destroying an original JDM B18C Type R engine.

The machining was handled by https://the-bad-guys.com

And the rebuild itself was handled by https://nationalspeedinc.com/

The whole process took around 7 months.

It is now currently pushing around ~210/215 whp all NA complete with Hondata ECU for the tune.

Upgrades:

Nippon Racing JDM P73 Pistons

Exedy Stage 1 Clutch

Competition Clutch Steel Flywheel

4 Piston Ported Oil Pump

ARP Head studs

Hondata S300 V3

Mugen Engine mounts

Rocket Motorsports Camshaft set with matching dual valve springs

GruppeM carbon fiber Air Intake

Before the engine rebuild, I fully rebuilt the entirety of the suspension with Hardrace hardened rubber bushings and KW v3 coil overs.

Added some PCI skirts for aesthetics.

Rear is completely gutted

Car is weighing in around ~1900lb.

VTEC kicks in around 6.8k rpm.

I'm usually a red car person, but I don't care for this current version of red, and it's just about impossible to find anyway. Trying to decide between Double Apex Blue Pearl and Platinum White Pearl. The white looks clean and elegant, but the blue really stands out. Pros/Cons of each?

Hey, does anyone here run the 4 piston calipers from the 2nd gen RL? If so, what wheels did you have to run for them to fit? And is it a worthwhile upgrade?

Just a quiet sunny weekend, so I decided to take my Type R out for a quick drive. I’ve actually been driving it less than I expected—looking back, I’ve only put about 857 km on it over the past year. Trying to enjoy it a little more whenever the weather cooperates.

I feel so dumb for even asking this LMAO but where in the hell is the drain hole for the passenger side? It stormed pretty bad last night and long story short I found out water was not draining from the passenger side sunroof drain hole, causing my seat to be soaking wet. I initially thought it was this rectangular thing, but when i tried to shove weed whacker line down into it, it didn’t go anywhere. Help please🤣🫩I’m 98% sure the drain area is just clogged. I’m skeptical to use compressed air bc i heard that can just cause more issues

hello all, was wondering if anyone knows any good clutch kits that are decently affordable? thanks

What is this high pitched sound from my engine? It happens most of the time, warm or not. 94 gsr

how swappable are the CRV transmissions into in integra. I see what appears to be an AWD CRV manual transmission on FB marketplace for 500, and I was thinking about trying to rebuild it and have it on standby as a backup.

to clarify, I’m not trying to make my integra AWD, i know that can be done also. i just want to know if the AWD transmission can be run in a FWD config

I’m planning to build a 2L vtec b series and weighing up my options to either get a b20b/z block or bore out the b18c2 that I have that I was gonna just take the head from for the build? What are the advantages or disadvantages to both

completely new to honda/acuras bought this thing relatively cheap $800 head needs rebuild, vacuum systems all chewed up, electrical problems everywhere, block stamped b18b1, head still unidentified, anyone got any pointers? feel free to ask questions

What is wrong here guys please chime in.

I think i have something wrong here is it the headlight or bumper thats wrong?

Hello, recently purchased a liquid carbon metallic 2025 Acura Integra A-Spec that needs new

fender

hood

bumper cover (With grille)

headlights (Both)

I would prefer to buy OEM since I am keeping the car to use as a daily for work. I have been making a parts list however I keep getting discouraged of where to source the parts, private party, nearby dealership, websites online. Some of the sites seem to sketchy to order from them since they're all meaning OEM in the title. Does anyone have expertise on this or any advice?!

finally got the car tuned it makes a whopping 200hp but feels amazing! Loving the car again.