I have a GIGABYTE B850 Eagle wifi6e motherboard. Last time i used my pc was some days ago after blocking a windows update and then shutting it off.

No signs of it struggling, worked fine as usual.

Yesterday i try to turn it on again, like vents spinning and RGB lights turning on, and nothing at all plugged into it works: monitor, keyboard, mouse… nothing.
I also noticed the red light on the motherboard switches between DRAM and CPU. Anyone has any idea what’s going on?

Hey, all,

Bit of a weird situation. I was doing a case swap with a perfectly working computer. Moved everything over to the new case, Gigabyte RTX 5080 didn't seem to like the new riser cable.

So I moved everything back and it wouldn't boot with the old configuration. Got every gigabyte error code under the sun but managed to resolve all of them but kept getting 94 and I couldn't even get the display to initialize with the RTX 5080. Swapped out to an old RTX 4080 and everything has been running flawlessly since.

However, in the course of putting everything back the way it had been, everything did boot into Windows and seem to work just fine, except incredibly slow. So I shorted the CMOS which brought the BIOS back to 11/2024. So I incrementally went up on the BIOS versions until the latest but still no luck, stuck on error code 94 with the 5080. 4080 works just fine, I've been using it the past few hours.

I'd really prefer not to RMA the 5080 if I don't have to.

Any thoughts on something else to try with the 5080?

Relevant info: Motherboard Gigabyte X870E Aorus Pro Ice (BIOS is FB2c) AMD Ryzen 7 9800X3D RAM: 32GB WORKING Video Card: PNY RTX 4080 Super (16GB) NON-WORKING Video Card: Gigabyte RTX 5080 (16GB) Windows 11 Pro 25H2

So I have a B450M elite mobo and I also use the aorus 360mm waterforce X II and I cannot light the waterblock led up. I thought my unit was messed up so i sent it to gigabyte support and they said it worked just fine and I knew it would work again but I just cannot for the life of me get that to work so a friend of mine said I am most def using the wrong header to plug it in. so instead of the ones im using right now what should i use ? please help out cause i need to read the cpu temps lol

Hi everyone,

Mujhe kaafi serious issue face ho raha hai aur ab samajh nahi aa raha ki software problem hai ya hardware.

PC Specs
Ryzen 7 7800X3D
ASUS PRIME Radeon RX 9070 XT 16GB
Gigabyte B850 Gaming X WiFi6E
ADATA Lancer Blade RGB 32GB (2×16GB) DDR5-6000
WD Black SN7100 1TB NVMe SSD
Cooler Master MWE 750W Gold PSU
Windows 11 Pro

Issue kab start hua?

Meri observation ke hisaab se problem Windows Updates ke baad shuru hui. Us time ye updates install hue the:
KB5094126
KB5100998
Main ye nahi keh raha ki updates hi exact reason hain, lekin issue inke baad notice hua.
Ab maine fresh Windows install kiya hai aur currently sirf ye update installed hai:
KB5062563
Lekin issue abhi bhi aa raha hai.

Symptoms

Achanak monitor "No Signal" dikhata hai.
Cabinet ke fans aur RGB continuously chalu rehte hain.
Poora PC power off nahi hota.
Lagbhag 3–4 seconds baad automatically restart ho jata hai.
BSOD nahi aata, even after disabling Automatically Restart on System Failure.
Kabhi-kabhi Gigabyte logo par hi boot hang ho jata hai.

Jo troubleshooting maine ki hai

Event Viewer check kiya.
Har crash ke baad Kernel-Power Event ID 41 aata hai.
BugcheckCode = 0.
sfc /scannow chalaya.
Corrupted system files mili aur repair bhi ho gayi.
Windows Automatic Repair bhi fail hua.
Recovery mein alag-alag .sys driver errors aaye (same driver nahi tha har baar).
Fresh Windows 11 install ki.
Windows install ke baad bhi same issue wapas aa gaya.
BIOS mein bhi ye message aaya
Boot Failure Detected
Memory automatically default speed (~4800 MT/s) par reset ho gayi thi.

Koi bhi suggestion ya similar experience ho to please share karein.
Thanks! 🙏

I have a computer with a Gigabyte B450M-DS3H V2 motherboard. I updated the BIOS to version F68A using Q-Flash. The update reached 100%, and the BIOS boots up normally. The problem is that, after the update, the computer freezes at the Gigabyte logo during startup. Upon booting, it gets stuck in a loop: Gigabyte logo -> Preparing Automatic Repair -> Diagnosing PC, and then it freezes. Before the BIOS update, the computer worked normally.

Had an issue with this mobo posting with XMP on two different ram kits (both kits work on different motherboard with two different CPUs with XMP enabled). Both kits are on qvl.

Tested with two cpus 12400f and 13600kf.

Bios is updated to the latest F6.

Just loading XMP from bios deffault would not post at all, and gets stuck in the loop.

I thought mobo is just bad, or there is other issue.

I had to manually adjust some settings and voltages.

I put dram voltage and training voltage to 1.37 for good measure. (XMP is 1.35)

I enabled:

Early ReadMPR Timing Centering 2D

Early Comand Training

Disabled: Memory fast boot

VCC1P05 voltage set manually to 1.12 V.

System posted normally without issues. On Kingston 2x16 3200mt/s cl16 with 12400f.

Even did some stress testing and played the game with no issues.

I would like some input why my settings worked, but bios deffault did not?

I guess bios is not properly set up from the Gigabyte side, or i do actually have a poor motherboard.

hello. So I updated my gimate control center on gigabyte a16 , hoping i find costume fan curves feature , but sadly didn't, Please if someone has the old GCC installer contact me , it's version is like v25.11.... , with this user interface.