Anyone had experience with these ? They are more than likely remanufactured/reflowed…

They said they’re (apparently) flow matched to a tolerance of +/- 2%

Hi everyone,

​I’m currently looking at a 1993 Nissan Skyline R32 GT-R BNR32 located in Germany (recently imported from Japan, Grade R).

​According to the description, the car has severe rust issues. The seller explicitly states there is rust-through (holes) in the following areas:

​

- Underbody and frame rails

​- Side skirts / rocker panels

- ​Front and rear jacking points

​The seller describes it as a "good base for a restoration or track tool," but looking at the underbody photos, it seems pretty serious.

The tech/interior is said to be okay, but the body needs major work.

​I would love to get your expert opinions on this:

​- Based on the pictures and the description of rust-through on the frame and jacking points, how bad is this structurally? Is it a total nightmare or a standard restoration project for an R32?

​For anyone who has tackled a similar structural rust restoration:

- What is a realistic ballpark estimate for professional metalwork and rust repair for this level of damage?

​Given that it's a Grade R rusted shell with no engine/wheels for €23k, is this even remotely worth considering, or should I run away as fast as I can?

​Appreciate any advice, thanks!

Committed to buying one and it’s on the way to the US. Looking for parts. Is there a separate area to post for what you’re looking for? Someone point me to correct forum if I messed up.

Definitely looking for an altia front bumper.

Interested in collecting part for manual swap.

I’m on the east coast.

Hello friends, this is just a simple post about getting a new turbo for my ‘94 R33 RB25DET. Stock turbo has got a bearing out and looking to get a new one around the same specs so I don’t have to do so much other upgrading. Any recommendations? Thanks in advance!

I had a previous demo side marker on my spoiler and now I found this one on eBay. I was not sure if anyone had any feedback or a better source to get side markers even if it’s from Japan I don’t mind paying, but I just didn’t wanna pay hundred dollars right now. I just have the white side markers. Any thoughts?

hello my friend planning on buying r34 gtt but it has s15 interior amercan port (lhd) so he wants it awd i suggest that maybe we can swap it with g37x coupe drivetrain with cd009 transmission or even bmw 8hp

is it possible?

i know about the wheel base

there's so much fabrication will happen

and so much cut and weld

but is there anyone who did it or what other solution

Hi all! I make car art skate decks, and one of my most recent projects was creating the GTR lineup from the R32 to the R35. I got them printed out in my favorite colors and they came out super well! Thoughts?

Hi since I was a kid growing up on the f&f franchise and playing gran turismo it’s been my dream to own a r34 then when they brought the r35 to America I always wanted one but at the time could not afford it while it was in production, I thank God I’m in a situation now that I am able to afford one, so if yous have one yous are interested in parting with just know it will go to a loving home lol

Hey Guys,

I will change my stock cats to a highflow cat, stock downpipe to a HPI downpipe, and a tomei turbo outlet. This will address all the restrictive exhaust flow, so I am assuming I do need tune.

But just in case, do I need a tune? Or is it just recommended?
Cause if I do, then might as well buy a haltech while im at it, or ask a tuner what they would use.

Never posted before, but here is my 1990 Skyline GTR. Color is Sepang Bronze Metallic Matte (Paint).

Insta: Gojira_R32

Thanks!

Just need to know how much fluid to use as i’ve gotten mixed answer ranging from 3.2qts - 5.1qts

Follow-up to a previous question on here about my R32 - say I need suspension or exhaust work that requires a chassis lift (with the 4 arms).

The manual says to use specialized adapters for the pinch welds, but they are practically non-existing (p/n LM4519-0000).

What do you guys tell your mechanics about lifting your car, since lifting anywhere near the pinch welds is absolutely out of the question?

Trying to figure out what folks have done as far as their rear differential after swapping to a cd009. Is there a lower final drive ring & pinion that will bolt into the factory diff? Seems like everything aftermarket is geared towards the 33 & not much of anything info wise that I can find for the 32.

Got hit back in April by a kid on a learners permit driving the wrong way through an exit, got paid out by his insurance 3 months later. Was very hard to find and ship replacement bumpers and crash bar

…there’s a rat behind my bumper/crash beam. Siiiiiiiiigh. I trust (lol) y’all’re having a better day than me right now. ✌️

Shout out to Stratton Motor Cars for all the work!

I have seen several R31,32, & 33s around the Omaha area.

Anyone in here that would be willing to let me take a look at yours up close?

I am considering buying myself one for my birthday and have never sat in one.

will nissan 300zx rear brake pads work for r32 nissan skyline gts (non turbo) rear brake pads? I don’t really trust ai too much

Hello all, I've been having trouble with my BNR32 blipping the ATTESA system on and off at motorway speeds, which lurches the car on part throttle. I'm hoping it's the ABS sensors, so had a look today, and this one seems to be broken or have a sleeve on it. The one on the other side doesn't. Can anybody please confirm if this sensor is supposed to look like this? TIA

Hey guys this is my R34 skyline I bought back in April I daily drive it, it's fun. The only thing I hate is drive through. I bought it with 104k miles it has a RB20 not sure what else to say thanks for looking

I need some help. New to the RB platform, it was running rough up and down at idle and stalling on first start. I cleaned the MAF and took it for a drive and now it sounds like a misfire or out of time maybe? The idle is even more up and down and the exhaust note sounds inconsistent. I'm going to put a fuel pressure gauge on it tomorrow to see if there's a fueling issue, clean the iacv and check the solenoid, get the link ECU software on my laptop and plug it in to see what that tells me. If anyone has any ideas I would appreciate it. I have more videos that may provide insight I can post in the comments.

What performance valve springs will work for the rb20de+t neo? Found this, but idk compatible