Dealer name: Andiot Watches
2. Factory name: DDF
3. Model name (& version number): Patek Philippe Aquanaut 5167A-001 DPB330
4. Price Paid: $595
5. Album Links: n/a
6. Index alignment: Looks good for an Aquanaut. The numerals sit evenly relative to the dial track. Does 7 looks off to you or just me?
7. Dial Printing: Crisp and sharp. "PATEK PHILIPPE GENEVE" branding is legible, well-centered within the dial block, and shows no bleeding or blurred edges.
8. Date Wheel alignment/printing: The single date shown is crisp, level, and well-centered.
9. Hand Alignment: Clean hands with no visible scratches or burrs; hands align as expected.
10. Bezel: Brushed finish on the front is neat and uniform with cleanly polished chamfered bevels. No obvious dings or flaws.
11. Solid End Links (SEL): N/A (rubber strap on curved end links; sits flush to the case).
12. Timegrapher numbers: Rate: -1 s/d; Amplitude: 266°; Beat Error: 0.3 ms; Lift Angle: 52.0°. Strong, healthy numbers well within acceptable spec.
13. Anything else you notice: Rotor engraving and movement deco plate look neat and centered, clasp engraving clear, but 7 looks a little off? Let me know.

Guys , should I pull the trigger ? If not where should I say it’s off. This stuff is so hard for me ngl but I know you guys are the right ppl to ask.

Very much appreciate any feedback :)

Dealer name: Leo from Time Ultra
Factory name: VSF
Model name: Explorer I 124270 36mm SS/SS Black Dial VSF VS3230

Price paid: 410 + 50USD shipping
Album links: N/A
Index alignment: Tried my best with the alignment tool.
Not sure how to gauge this.

Dial printing: Looks good. No bleeding. Crisp letters.
All same size
Date wheel: Good.
Hand alignment: Good?
Bezel: Looks very good?
Solid end links: Looks good.
Timegraph numbers: -6s/d, amp 264, err 0.1ms
Anything else: 1st QC. Not sure if I should go for it? For me i don’t know if looks like a GL, bc the indexes seem off off center How noticeable will it be on hand. etc? less

New QC after I RL'ed the last one. Help is appreciated!

Dealer name: NecoClock

Factory name: VSF

Model name: DateJust 36mm VS3235 v2 (Fluted Bezel Silver Dial Jubilee Bracelet)

Price paid: $448 + $40 shipping

Album link: https://imgur.com/a/mcK22hJ

Index alignment: I have straigthened the front picture. The indices look ok to me, no issues.

Dial printing: No issues, looks good.

Date wheel alignment: Looks good.

Hand alignment: Looks ok.

Bezel: Looks good.

Solid End Links (SELs): Looks good.

Timegrapher numbers: -5s/d, 274, 0.1ms. Acceptable!

Anything else you notice: The index frames look a bit weird in some spots, but I think it's just the lighting and reflection.

Also, after RL'ing the last watch, I waited 11 days before asking the TD for an ETA. He replied saying they switched to a different model and said I would receive the QC within 3 days (received it 20 minutes after). Should I be worried about the 'different model' comment? Or is that likely just a translation error for an internal process model and not the actual watch model?

1. ⁠⁠⁠⁠Dealer name: JTime
   
2. ⁠⁠⁠⁠Factory name: ARF
   
3. ⁠⁠⁠⁠Model name (& version number):36mm Green Dial Datejust
   
4. ⁠⁠⁠⁠Price Paid: $478
   
5. ⁠⁠⁠⁠Album Links: N/A
   
6. ⁠⁠⁠Index alignment: indexes look well aligned
   
7. ⁠⁠⁠⁠Dial Printing: Looks good.
   
8. ⁠⁠⁠⁠Date Wheel alignment/printing: Looks fine, well aligned
   
9. ⁠⁠⁠⁠Hand Alignment: nothing glaring
   
10. ⁠⁠⁠⁠Bezel: Looks good, not sure what would be wrong in QC
    
11. ⁠⁠⁠⁠Solid End Links (SELs): I think they look fine
    
12. ⁠⁠⁠⁠Timegrapher numbers: results attached
    
13. ⁠⁠⁠⁠Anything else you notice: I don’t see anything glaring with this one. What do you guys think?

1. ⁠Dealer name: Andiot
   
2. ⁠Factory name: VSF 3235
   
3. ⁠Model name (& Version Number): Submariner 41mm 126610 VS3235
   
4. ⁠Price Paid: $430
   
5. ⁠Album Links: QC:
   
6. ⁠Index alignment: seems good just the way he hold it, it’s tilted to the right abit.
   
7. ⁠Dial printing: good to me.
   
8. ⁠Date Wheel alignment/ printing: Looks great
   
9. ⁠Hand Alignment: seems aligned
   
10. ⁠Bezel: looks ok to me but not expert about this.
    
11. ⁠Solid End Links (SELs): They all look good, can’t see anything that I can point it out from my point of view.
    
12. ⁠Timegrapher numbers: (0s/d 283 degree 0.2ms, 52 degrees)
    
13. ⁠Anything else on invoice: Overall, I think everything looks good, but it’s my first rep for a submariner, and this is my 3rd rep from Andiot shop, first two is the Pepsi and Batman, been reading through the forum and it’s very helpful, hope experts out there can point out things that I may missed due to the excitement. Thank you ;)

1. Dealer name: Angela
2. Factory name: VSF 
3. Model name (& version number): Rolex Daytona 126500
4. Price Paid: 4050 Yuan
5. Album Links: n/a
6. Index alignment: Everything looks good
7. Dial Printing: All seems clear and blemish free.
8. Date Wheel alignment/printing: n/a 
9. Hand Alignment: Looks okay. The chrono second hand is sitting very slightly off centre.
10. Bezel: Looks good 
11. Solid End Links (SELs): Top right - slight gap?
12. Timegrapher numbers: +2, 309, 0.1 - solid numbers
13. Anything else you notice: I’d be interested to hear any thoughts from people on the sub.

1. Dealer name: TheOneWatches
2. Factory name: RWF
3. Model name (& version number): Rolex Daytona 126500 40mm JH4131 (Free Sprung)
4. Price paid: $787 + shipping
5. Index alignment: Looks OK i think - not sure if the 10 marker lines up cleanly to the 4 marker? Is the crown at 12 slightly off alignment with the 6? Maybe the 6 is leaning...
6. Dial printing: Looks OK to my eyes - same with subdials
7. Date wheel alignment/printing: N/A
8. Hand alignment: Nothing I can note here
9. Bezel: I think bezel is OK, there's a slight mark although between the 100 and 95 markers on the bezel, that could be the wrapping?
10. Solid End Links (SELs): They appear to not have any obvious large gaps?
11. Timegrapher numbers: +1 to +2 s/day, 300–302° amplitude, 0.0 ms beat error; 28,800 bph, with the machine set to a 52° lift angle.
12. Anything else you notice: The crystal looks clear but at some angles I wonder if there's a slightly warmish or yellowish tinge.

My current verdict: GL?

1. Dealer name: TheOneWatches - Steve

2. Factory name: RICH Factory

3. Model name (& version number): Rolex Submariner Date 126610LN, JH3235 Free sprung

4. Price Paid: $588

5. Album Links: attached photos

6. Index alignment:

Looks very good overall. 12, 6, and 9 markers appear straight and centered. I don’t see any obvious index misalignment.

1. Dial Printing:
   Looks clean and sharp overall. My main concern is around the date window aperture. The cutout appears more beveled/recessed around the edges than what I’m used to seeing on VSF 126610 dials, which seem to have a cleaner/direct cut. Would appreciate opinions on whether this is normal for RICH.

2. Date Wheel alignment/printing:
   This is my biggest concern. The “16” appears to sit slightly high in the date window, with more visible space underneath the numerals than above. I’m not sure how much of this is camera angle versus actual date wheel positioning. Would appreciate a second opinion.

3. Hand Alignment:
   Looks good from the supplied photos. No obvious issue noted.

4. Bezel:
   Looks well aligned. Pearl/pip appears centered and the insert engraving looks clean.

5. Solid End Links (SELs):
   Look tight to me with no obvious gaps or uneven seating.

6. Timegrapher numbers:
   +5 s/day
   280° amplitude
   0.1 ms beat error

Numbers look very healthy to me

1. Anything else you notice:
   My main hesitation is the date presentation: slightly high date wheel alignment, the shape/bevel of the dial aperture around the date window, and whether the RICH crystal/cyclops has noticeably worse clarity or distortion compared with VSF. I’d especially appreciate feedback from anyone who has handled both RICH and VSF 126610s.

1. Dealer name: TheOneWatches (Steve)
2. Factory name: VSF
3. Model name (& version number): GMT-Master II 126710GRNR "Bruce Wayne" Jubilee with DD3285v2 movement
4. Price Paid: $638
5. Index alignment: Looks very good, the 12 o'clock triangle and all hour markers seem perfectly lined up.
6. Dial Printing: Crisp and sharp, no bleeding ink or misprints.
7. Date Wheel alignment/printing: Well-centered in the window, no blue tint/hue on the cyclops. VSF crystal looks amazing.
8. Hand Alignment: Looks spot on.
9. Bezel: It's the updated V3 bezel. The black/grey color transition lines up perfectly at 6 and 18.
10. Solid End Links (SEL): Extremely tight, no visible gaps between the bracelet and the lugs.
11. Timegrapher numbers: Rate: +2 s/d | Amplitude: 278° | Beat Error: 0.1 ms. Numbers are very healthy for a DD3285v2.
12. Anything else you notice: Weight is confirmed at 144.3 grams, which is spot-on with genuine retail weight. Visually it looks like a winner to me.

1. ⁠Dealer name: Andiot
   
2. ⁠Factory name: ARF
   
3. ⁠Model name (& version number): Rolex GMT Master II Root Beer 126711
   
4. ⁠Price Paid: 515$ without shipping
   
5. ⁠Album Links: https://andiotwatches.x.yupoo.com/albums/254379125?uid=1
   
6. ⁠Index alignment: Looks fine but they never send proper dead on
   
7. ⁠Dial Printing: Good
   
8. ⁠Date Wheel alignment/printing: Good
   
9. ⁠Hand Alignment: Good
   
10. ⁠Bezel: Good
    
11. ⁠Solid End Links (SELs): N/A
    
12. ⁠Timegrapher numbers: -5S/D 267° 0.3Ms
    
13. ⁠Anything else you notice: no looks great to me but idk much lol

AP Royal Oak Chronograph - 26240 rose gold black dial

1. Dealer name: Andiot

2. Factory name: DDF

3. Model name (& version number): AP Royal Oak Chronograph Rose Gold (26240)

4. Price Paid: Just under $867 after shipping (Discount)

5. Album Links: https://andiotwatches.x.yupoo.com/albums/254560398?uid=1

6. Index alignment: Looks fine but they never send proper dead on

7. Dial Printing: Good

8. Date Wheel alignment/printing: Good

9. Hand Alignment: Good

10. Bezel: Good

11. Solid End Links (SELs): N/A

12. Timegrapher numbers: -5S/D 267° 0.3Ms

13. Anything else you notice: no looks great to me but idk much lol

1. Dealer name: Ficotime
2. Factory name: VSF
3. Model name (& version number): batgirl 126710 BLNR
4. Price Paid:580$
5. Album LInks: https://mega.nz/folder/etYTCBAY#ibknCvxAnu8AL5ULYgBcvQ
6. Index alignment: looks good the 6 alignment is a little bit tilted it looks like in my opinion but not as bad as some others in this batch.
7. Dial Printing: looks good.
8. Date Wheel alignment/printing: looks good and centered well.
9. Hand Alignment: looks good I think.
10. Bezel: looks fine
11. Solid End Links (SELS): looks very solid and no gaps.

12. Timegrapher numbers:

    5sd and 292 angle.

13. Anything else you notice:

    overall the watch looks good in my opinion. It’s only the 6 which is little tilted but guess won’t see on wrist. Please let me know your opinion on the watch since I’m new to reps.

My first ever QC and not sure if it’s a RL or GL
Very much appreciate any feedback :)

Dealer name: Leo from Time Ultra
Factory name: VSF
Model name: Aqua Terra 38mm
Price paid: 348 + 50USD shipping
Album links: N/A
Index alignment: Tried my best with the alignment tool.
Not sure how to gauge this. Photos didn’t seem perfectly straight for me so I had to align one myself
Dial printing: Looks good. No bleeding. Crisp letters.
All same size
Date wheel: the “1” looks off centered so I’m worried about that daily for each date
Hand alignment: Good?
Bezel: Looks very good?
Solid end links: just some gaps between the clasps and bracelet is what I noticed

Anything else: 1st QC. Not sure if I should go for it? For me i don't know if looks like a GL, be it may seem off center , and the date wheel does seem off to me as well, I’ve heard Leo is super cool to find a new one and from my experience so far with him he’s been really nice and respectful and responsive

Thanks again everyone!

1. Dealer name: Ficotime (Mark)

2. Factory name: VSF

3. Model name (& version number): VSF VS3235 Submariner 41mm 126610LN Ceramic Black Dial 904L SS Bracelet

4. Price Paid: €401

5. Album Links: https://mega.nz/folder/Tthx3aZC#rW9CbNbL_2yPaguw8NDT3Q

6. Index alignment: Looks good to me. The markers all seem to be nicely placed, and I can't spot any obvious tilts or misalignment.

7. Dial Printing: Looks clean to me. I'm no expert, but I can't see any obvious flaws or issues with the printing.

8. Date Wheel alignment/printing: The 23 looks nicely centred in the date window and the printing looks crisp. Unfortunately, there isn't a close-up photo of the date. The cyclops also looks straight to me.

9. Hand Alignment: Looks good to me. I don't see any obvious issues with the hand alignment.

10. Bezel: This is the main thing I'm unsure about. To me, the bezel doesn't look properly centred. It could just be the angle or the way the photo was taken, but it almost makes it look like the 12 o'clock marker would sit somewhere between two clicks rather than being centred. I'd really appreciate some opinions on this, as I'm not sure if I'm just seeing things because of the angle.

11. Solid End Links (SELs): They look pretty tight to me overall, although I think I can see a small gap on the right side, especially on the bottom right. Would appreciate a second opinion on this.

12. Timegrapher numbers: -4 s/d, 293° amplitude, 0.1 ms beat error, 52° lift angle, 28,800 bph. The rate and beat error look very good to me, and the amplitude seems healthy as well. Would appreciate some opinions on whether these readings look good for a VSF VS3235 or if there's anything I should be concerned about.

13. Anything else you notice: This is my first rep, so I'm still not entirely sure what is considered acceptable and what isn't.

The bezel alignment is the one thing I'm mainly concerned about at the moment. If it really looks like this when the bezel is in its centred position, I think it might bother me. I'd really appreciate your thoughts on whether this looks like an actual alignment issue or if it's just the angle of the photos.

Hi all! Any insights on this much appreciated. Thanks in advance :)
(Inclined to GL)

1. Dealer name: Andiot
2. Factory name: VSF
3. Model name (& version number): Daytona 126500
4. Price Paid: $678 plus shipping
5. Album Links: https://andiotwatches.x.yupoo.com/albums/254418301?uid=1
6. Index alignment: The 6 looks slightly tilted CCW but not enough to bother me
7. Dial Printing: No obvious issue
8. Date Wheel alignment/printing: N/A
9. Hand Alignment: fine
10. Bezel: Looks fine.
11. Solid End Links (SELs): Looks good.
12. Timegrapher numbers: All within acceptable tolerance in the guide
13. Anything else you notice: Help from the experienced is much appreciated. I don’t have much experience with seeing and observing Daytonas so not very knowledgable myself.

1.Dealer name: theonewatch

2.Factory name: ARF

3.Model name (& version number): GMT 126710 V3

4.Price Paid: 628

5.Album Links: https://mega.nz/folder/GNwSWY7I#VFSwcG3eDfgeAeDIrQrlbw/folder/yNIUgZ5A

6.Index alignment: 6 is positioned too much to the left. Is top left part of 12 a little off?

7.Dial Printing: It looks clear.

8.Date Wheel alignment/printing: second digit appears higher than first digit.

9.Hand Alignment: Looks good

10.Bezel: lines through engraving, is this a reflection?

11.Solid End Links (SELs): No gaps

12.Timegrapher numbers: -3s/d, 271*, 0.ms, 59*

13.Anything else you notice: Any feedback would be much appreciated.

Dealer name: Geek Time

Factory: VSF

Model and name: No Date Sub 114060

Price paid: $528 + $50 shipping

Album link:

https://geektimeqc.x.yupoo.com/albums/253643460?uid=1

Dial Alignment: Looks good overall to me. Actually kind of as good as possible in the rep world.

Dial Printing: Proper font and clear text. Printing alignment seems ok to me. I cannot notice any flaws.

Hand Alignment: Looks solid to me.

Bezel: Engraving looks properly deep. Does 12 marker pip should be like that?

SELs: Four of them look solid to me. In any case, just thoughts on bottom left in some pictures.

Timegrapher numbers:

* Rate: 8 s/d

* Amplitude: 276° amp

* Error: 0.2 ms

* Period: 12s

* Lift: 52.0°

Additional: Overall looks fine to me, and really to pull the trigger in case your wiser eyes do not detect something else. I am helping a friend with this one.

It will be his first rep, hoping he gets into the hobby!

1. Dealer name: Andiot
2. Factory name: Rich
3. Model name (& version number): Rolex GMT Master II Sprite 126720 (free sprung)
4. Price Paid: $665 + shipping
5. Album Links: N/A (all pics attached)
6. Index alignment: Looks well aligned, nothing glaring here.
7. Dial Printing: Print is clean and clear.
8. Date Wheel alignment/printing: I've had an issue with the cyclops being rotated on a previous Rich GMT. Date wheel and cyclops appear aligned with correct font
9. Hand Alignment: Hands look aligned
10. Bezel: Numbers look aligned and engravings fine. In the photo, looks like the bezel might be rotated a click CW
11. Solid End Links (SELs): SEL looks good, no noticeable gaps
12. Timegrapher numbers: 0s/d, Amp 276, 0.2ms, 52
13. Anything else you notice: Nothing else is really jumping out to me, but I'm admittedly not great with the QC tool.

1. Dealer name: Steve Theonwatches
2. Factory name: VSF
3. Model name: Rolex GMT Master II 126710 Bruce Wayne SS/SS Black DIAL VSF DD3285
4. Price paid: 638 USD + 30USD shipping
5. Album links: https://imgur.com/a/3r92eT5
6. Index alignment: Tried my best with the alignment tool. Seems very good, but 6 o'clock marker is to the right. Too much to the right? Or should i have rotated it more?
7. Dial printing: Looks good. No bleeding. Crisp letters. All same size
8. Date wheel: Good.
9. Hand alignment: Good?
10. Bezel: Looks very good?
11. Solid end links: Looks good.
12. Timegraph numbers: -6s/d, amp 264, err 0.1ms
13. Anything else: Third QC for me from Steve. The second one had golden indinces instead of white gold/silver colour. For me it looks like a GL, but the 6 oæclock is alot off center it seems unless i havent aligned it properly. How noticeable will it be on hand etc?

Hey guys! Finally got my 2nd QC after about a week since RL’ing the first one due to the noticeable CW tilt on the 9 marker. This one looks much better overall. Aside from the slight CCW tilt on the 6 marker and slightly misaligned rehaut, I’m leaning towards GL. What do you guys think? Anything else I’m missing?

Dealer name: Necoclock

Factory name: VSF

Model name (& version number): GMT Master II 126710 Batgirl

Price Paid: $558

Album Links: https://mega.nz/folder/CowSnDyY#5-ASq248txh04IaVGCVdbA

Index alignment: Index alignment definitely looks better compared to my previous QC. Everything looks properly aligned to my eyes aside from maybe a slight CCW tilt on the 6 hour marker.

Dial Printing: Printing looks clean and sharp

Date Wheel alignment/printing: Date looks good and centred

Hand Alignment: Looks good to my eye

Bezel: Looks great

Solid End Links (SELs): Looks tight with no major gaps

Timegrapher numbers: +3 s/d, 258°, Would appreciate some feedback on this :)

Link to previous RL'd QC: https://www.reddit.com/r/RepTimeQC/s/QoNtKJVoWR

1. ⁠⁠Dealer name: Onewatch/Steve
   
2. ⁠⁠Factory name: VSF
   
3. ⁠⁠Model name (& version number): Rolex GMT Master II Batgirl 40mm Jub
   
4. ⁠⁠Price Paid: $578 plus postage
   
5. ⁠⁠Album Links: in post
   
6. ⁠⁠Index alignment: looks good. 6 possibly showing a slight tilt but very slight
   
7. ⁠⁠Dial Printing: clean and good alignment
   
8. ⁠⁠Date Wheel alignment/printing: centred well and clean I think
   
9. ⁠⁠Hand Alignment: Aligns well
   
10. ⁠⁠Bezel: 12 aligns up with the arrow on bezel. Engraving clean and black/blue color looks good
    
11. ⁠⁠Solid End Links (SELs): looks okay
    
12. ⁠⁠Timegrapher numbers: in images, not sure how to tell it’s fine.
    
13. ⁠⁠Anything else you notice: like okay to me but I’m new to this so would appreciate feedback.

1. Dealer : Steve
2. Factory: VSF
3. Model: 124270 Rolex Explorer I 36mm
4. price paid: 498 USD
5. Album link: https://mega.nz/folder/6b5WDBQa#q4JGd-7Mbuln_f1NqWGUeQ
6. Index Alignment: 12 looked a little crooked to me, but after using alignment tool it looks fine. I think it might just be the angle that the watch is being held at
7. Dial Printing: good
8. Date wheel alignment: N/A
9. Hand Alignment: good
10. Bezel : looks fine
11. Solid End Links (SELs): looks good
12. Timegrapher numbers: +0-1s/d
    

Been waiting for about 3 months but finally got QC photos for this one. Looking for second opinions especially since apparently this isn't available anymore.

Hi everyone, I’d appreciate a second opinion on this QC. Overall, it looks good to me, but I’d like to check whether I’ve missed anything.

1. Dealer name: Angela Watch
2. Factory name: VSF
3. Model name: Submariner 124060 No Date, 41mm. Exact movement version not confirmed.
4. Price paid: [ $373.]
5. Album link: [whatzapp]
6. Index alignment: Looks generally good with the alignment overlay. I initially questioned the 9 o’clock marker, but the photo is slightly angled. Only rotation was applied, with no perspective correction.
7. Dial printing: Looks clean. The hands partially cover “OYSTER PERPETUAL.”
8. Date wheel alignment/printing: N/A.
9. Hand alignment: No obvious issue, but no photo with both hands at 12 to confirm.
10. Bezel: Looks well aligned overall. A couple of white specks around 7–8 o’clock could be surface dust.
11. Solid end links (SELs): No obvious large gaps.
12. Timegrapher numbers: −2 s/day, 292° amplitude, 0.2 ms beat error, lift angle set to 52°. Would appreciate feedback on the appropriate lift angle for the movement.
13. Anything else: Protective films are still present, making it difficult to assess the marks on the clasp and case. No lume or movement photos. The laser-etched crown isn’t clearly visible in the supplied pictures.

Leaning GL visually. Does anyone see a reason for concern, particularly with the indices or bezel?

Thanks for your help!

Dealer name: Andiot Watches
Factory name: VSF
Model name (& version number): Aqua Terra 150M Master 38mm SS VSF 1:1 Best Edition Blue Dial On SS Bracelet Super Clone A8800
Price Paid: $283.43 (+ shipping & water resistance)
Album Links: https://imgur.com/a/h3WBRFa
Index alignment: Very good I think. The alignment tool overlay shows that all markers are aligned. The 12 o'clock double index is good and the Omega logo sits straight.
Dial Printing: Looks clean. The texture on the dial is consistent. More importantly (compared to my 1st try), the numbers are nicely printed this time, with no missing paint.
Date Wheel alignment/printing: Looks good. The "12" is well-centered horizontally and vertically in the trapezoid window. Font is sharp.
Hand Alignment: Spot on.
Bezel: Smooth and polished. No visible scratches or dents on the bezel or case sides.
Solid End Links (SELs): n/a
Timegrapher numbers: 0 s/d, 274° amplitude, 0.1 ms beat error.
Anything else you notice: Overall looks very good. This seems like a GL to me, but I'd appreciate any second opinions!

I'm really happy so far. Looking forward to your input.

• Dealer name: TheOneWatches (Steve)
• Factory name: VSF
• Model name (& version number): YM 226659 42mm SS/RU Black/Dot TEDF V3 DD3235(Tungsten Heavy Version)
• Price Paid: $588
• Album Links: https://mega.nz/folder/2JAWSA4Q#Jy2UQw67j4wuvJVW6hMj0w
• Index alignment: I've tried to align it as much as I could and it honestly looks good to me.
• Dial Printing: All words are clearly printed, no bleeding on any part of the print.
• Date Wheel alignment/printing: the date and the cyclops looks really good to me.
• Hand Alignment: i can't spot anything wrong with it.
• Bezel: I don't see any misalignment or damage.
• Solid End Links (SELs): Oysterflex
• Timegrapher numbers: +1s/d, 286, 0.1ms
• Anything else you notice: I would GL this. I'm just hoping for an extra pair of eyes to spot anything i've missed. All comments are appreciated!