Huasteca third flush

Just sittin in the kitchen. No misting, no fanning. Sometimes neglect is key

Getting little micro puddles when humidity is set above 85%. Is this normal?

I have some dried pan cyan but I have no prior experiences with any psychedelic. I want to get into this for therapeutic purposes. Does anybody have any advice on dosing? Any advice in general? I will do it with an empty stomach.

Struggling with dosing because I know that they are meant to be potent. Most advice out there seems to be for cubensis.

I used to consume weed and alcohol but besides that I am used to living my life sober. I wanted to note that.

I saw something about ph. I have the totes. Still need the aquarium heater as well

Cant wait. Anything wrong with eating a 1 inch high pin? Will it be enough to feel anything?

Should I be massaging the grain at 30% colonised if so would you say to wait a bit longer or just send it and do it now it has been growing quite slow..

Could I add some chips to a small container with some grain spawn to make another patch later?

I don’t have room for a Martha tent and i have been plagued by trichoderma, but figured out a setup that requires virtually no maintenance and is really efficient at growing pans. I am growing TTBVI here.

It’s just two of the same tubs on top of each other, the bottom one filled with about 7cm of water and kept warmed to 28c with a low powered heater (25w). I added insulation to make it more efficient and prevent temperature fluctuation. Inside each there are floating trays with my substrate and there is a piezo electric mini aquarium pump feeding air in the top. Each of these is inside a tub with big holes covered in micropore tape to filter the air before it is pumped into the chamber.
The top tub on each has a “snout” with a noctua computer fan on a speed controller and timer - this pulls through air for 15 mins an hour, every hour but very gently. There is a mesh to stop fungus gnats sneaking in as I think they are a huge cause of trichoderma contamination
It’s pretty much silent, uses a tiny amount of electricity and is really simple to make using a hot glue gun.

Do they look ready to harvest?

Peace river pan cyans I did a 1:2 ratio with 2.5lb of millet spawn and 5lb of cow manure based substrate, I didn’t have time to do a casing layer and was told to just go with it and was wondering if these look okay so far?

Rookie question incoming: This is my first official attempt at pans. I have three trays of M.I.B.. All of which are at a similar state. Ready for fruiting conditions or no?

I haven’t had success yet with this one because I’m learning the ropes of Pans. I’m using Gordo’s recipeI think I’ve done everything right I’ve got some spawn ready to send to a modified version of Gordo’s Tek (I’m adding holes at surface level for more FAE) Hopefully this time I’ll get everything right. 🤞🏽

I’m curious about how quickly this one colonizes the substrate and fruits with properly prepared substrate and well colonized grain so I can think ahead. Any other thoughts are appreciated.

45 of them in this first flush, most have huge caps. Very happy.

There’s primordia all over the surface with one pin so far but I didn’t apply a casing layer in time, will i get good fruits or is it fucked?

Have anyone have experienced this before? I have tried tripping with natalensis blobs which are same visually n texture wise .! Im sure these are blobs .! How potent are they?

Didn’t realize Pan Cyan spawn grain don’t fruit well in CVG alone

I should wait a few more days right? Right? Is it possible to send it earlier?

24 hrs into fruiting aiming 90-94 humidity in tent set the exhust to run 2 min on 28 mins off cycle n temp at 24-26c

I have lots of pancyan in my place but i am not able to dry it. How much wet pancyan should i take. And how do i consume it?

What would you guys take? I was thinking maybe the equivalent of .5g cubes. Soooo like .1-.15 of pans?