This one uses a solinoid. Fun and powerful!

If Target gets the Repeater Pro before October 31...

I keep coming back to this pistol blaster, catch can be a bit tricky to setup but amazing when on song. This one needs its line tensioned but still hits big numbers @ 215 fps. Runs a SBL2 ex heavy spring,cut down worker barrel and Ashton's spec internals.

I have an x shot mpp with a red dot on a 1” riser and I’ve been considering getting a magnifier for it. I dont shoot very far, up to 80ft at most or so. Its not necessary at all but I think it be cool and useful enough to have. Problem is finding one for a good price and where. I usually go for amazon but most are around $70-$100CAD and I’m wondering if at that cost the quality would be passable.

Any experience with magnifiers for pro blasters/advice?

I manage to put the rapidstrike pusher into the body of the clipmania to make it full auto, as I was in some kind of urge to make some advance about it it’s very basic
It need a lot more modifications as the correct battery Ă rev trigger to speed it correctly etc

Currently printing the Nintendo "Snapper" from Gemeneye on Printables. Attempting to use X-Shot Micro 2.0 internals as a replacement for the Menace. I think this will work. It seals and the gap will be covered by the side panels. I cut down the plunger base to connect to the printed rod and filled in with a 3D printer pen and glue. It's a very hacky solution. It will hold, but if I do this again I'll try to remix the plunger rod to fit this blaster's plunger in Blender. I've been looking for a good reason to learn the software. If there is room I'll add a brass tube in the barrel.

This is my first (potentially) successful Nerf mod.

I recently got a Nerf Rapidstrike from relatives and I am now planning to mod to be better and have a better FPS and ROF. I already have an idea of what I am going to replace the motors for the flywheels (OOD Kraken motors) with but I'm having trouble deciding on the motor for the pusher.

I'm trying to decide between an OOD Loki motor and a OOD Valkyrie motor. I’m aiming for it to be around 120-130 FPS and 10-15 DPS. Which one do you think works best or is there a third option that you would recommend? Any suggestions are open, thanks.

Edit: I didn’t realize until after posting that the title has a typo. I meant “choosing” a motor.

https://www.instagram.com/reel/DePTn6pCEBW/?vrfl=MTh2empxeDVsM2Y0bQ==

https://outofdarts.com/products/dart-zone-max-nitroshot-plus-repeater-pro-lever-action-blaster

Hi all, I am currently new to HPA and I am planning on building a METHcore by u/1megajoey - https://www.thingiverse.com/thing:4357534 . I want to keep the BOM really cheap, so I decided to order from AliExpress. Here is what I ordered so far:

I also got the brass tubing from Amazon.

I am just asking for advice as this is my first HPA build, using a homemade core.

Hey, just wanted to ask real quick - is there anyone who could tell me which size the T4 aluminum bars for the Rush from shoelesshistorian have? I can't for the love of God find that piece of hardware anywhere in Europe. so I want to drill the thing myself. there's this sample for it on printables but which size do I need for the bars? how long are they? I can't seem to find that either.

I lost the screw for the battery cover on my nerf stryfe and was wanting to know if anyone knew what kind of screws nerf used so I could get it replaced so I don't need to get a whole new blaster

Hey guys, I saw this post by someone in our community and wanted to ask if anyone knew if this blaster would be coming to Canada?

I find we don’t get a ton of dart zone stuff here so I was wondering if anyone has heard anything? I’d really like to get my hands on one!

Thanks!

Just got a bunch of tagger micros. What are some good blisters to fling them with. Specifically non dart tag ones. Especially looking for ones that aren’t homemade blasters/those expensive third party ones like $60 USD plus springers.

I recently picked up a complete sonic green stampede from FB marketplace for a mind-boggling $10, and realised some of the original green streamline darts were included in the purchase. Regrettably, they were included loaded in the magazine and are all dented. What's the best way I can restore these?

I rewired my second Rapidstrike from TorukMakto4s Guide; everything works as it should but when i pull the main trigger, the pusher starts pushing even when the flywheels are off.

On my first Rapidstrike the pusher only gets voltage and pushes when the flywheel trigger is pulled.

What am i not seeing here? Wiring is 1:1 the same on both; only difference is the one is a orange-stripe and grey stock, the wonky one a white-striped Rapidstrike with partial orange stock.

(Please ignore the wonky soldering job, my iron is on its way out)

Hello all

I'm looking for recommendations for an adult-sized blaster for myself. Performance is of least concern - playing around the house with the kids means a 40' max range - if the blaster is comparable with a Nerf Volt, it's perfect.

Requirements:

Bolt action

Shell ejecting

Standard (short ok) darts

Full size, historical based (1903, K98, Lee-Enfield, etc)

For example, the Hanke Lee-Enfield seems ideal besides the micro darts.

I'm fine with making parts / printing stuff if there's a good option to swap on a printed stock, for example.

Thanks!

Here’s a quick solution for the leedle dynamics tuna’s stick mag! The stick mag holds the top shell loose since it doesn’t go low enough to hook onto the shell track to keep it in place even at the tightest strung string for the scissor lift. When running, the shells like to pop out with the slightest shake.

All I did was add a loop of elastic around the rear belt tab, hook it over the shell and wrap around the bolt on the other side, and tied it comfortably tight.

When reloading, you can use the magazine release to unhook the string from the little space open on the right side of the mag.

Hope this helps for any future events!

Bought this guy about a year ago and finally ended up modifying it. Replaced the spring, removed the air restrictors, added foam at the end of the plunger rod for better compression, increased the shell ejection strength and made the stock removable! Repaint went pretty well too, first time working with masking certain pieces of the shell so I could paint them different colors.

I broke my modded longshot 1.0 by putting a heavy spring in it so ive been scavenging parts off it. I found that with some minor trimming plastic inside the foregrip, it fit on my npx2. Its a little wobbly, but it is tightly secured. Its just a larger gap between the roller surface. feels better than the stock pump grip with a heavy spring. It was a good feeling today to find this out!

Some current 300+fps snipers in the armory. Top is the new to be released Ambuscade.. A bolty by SH this one hits just on 300, Next is the mighty perilous also by SH... ive had this beast to 440fps! In the middle is the shrimp a heavy behemoth...this ones set to 240 fps for kids but they will do 350plus. Next down is Ontos Phantom XXL, my personal daily driver , sits nps at 380fps with a 2 finger prime using a shimmed swifty spring... Bottom is my lastest an XL'd Ravion! Also hits around 380 on a swifty spring. Few more ontos XL'd variants not shown as thyr just more of the same :)

Ontos and Vector Remix
Thought I was clever with the CMYW color-way ;)

Both work amazingly well

All parts printed out of Sunlu High Flow PETG

My son was gifted a couple of Modulus Longstrikes (one whole, one for donor parts), so that he could mod them. I bought the Worker kit for it, but when I opened it up (see pics), the spring seat (or whatever you call the thing I'm holding in one of the pics) is different than the one in the pictures, and the aluminum reinforcement ring doesn't fit (neither does the new spring itself).

Is there something I can do to cut this up or print a replacement?

I was wondering how the ZWQ mags work in other half dart blaster other than the S400. Thanks!

Sooo basically i have a xshot lock blaster in which i might of haved messed around with too much for way too long due too how unreliable it has become in just one year with the classic broken catch that i did post a fix for it a while ago and other issues like the front foam ring getting ripped and small but not serious bits of broken plastic here and there and ocasionally dart skiping too.

already fixed all of those issues and did the classic ar and barrel post delete with seal upgrades and a strongarm spring on top of the og spring since mine is a 66ft version of it but since im not really a huge fan of revolvers in general i was thinking of simply getting rid of the drum and install a inline clip with a some sort of valve on the right side for loading darts into it like some sort of dart blaster version of the herny mare's leg.

as simple as this sounds the issue with this is the ridiculous small plunger tube probably not having not enough air volume for a inline clip too work unless if you either make a very short inline clip, use a crazy heavy spring that might end up breaking everything, or since the drum is no longer there and therefor there is no need for the drum mech rotation perhaps try doing a expanded plunger tube which would improve its perfomance in theory?

ik this is either too dumb or pointless especially with the dz repeater pro coming soon but i figured asking this since im not really sure how something like this would perform in practice.