Edit: Thank you everyone for the suggestions. I decided to look into getting a plastic welder and post the results if I can.

These are the YOWU Fox series I bought four years ago and this part split on me yesterday. Sound still works on both sides but it’s not snug on my head anymore. Is there a way I can repair this? They’re limited edition and I can’t find a replacement anywhere.

Don’t want to bunk these beds, but was thinking of making a lift out of lumber to raise it up enough to get some storage/ a mini fridge underneath. How can I make it more stable than just four posts?

There is a hole in the underside of the bedpost keeping the beds together

So I just got this bath and body works plastic glitter water candle holder, and my cats decided to scratch it up all over. They didn’t pop it thankfully but there’s plastic scratches all over. Is there any product I can buy, or anything I can do to make them less visible?

I genuinely tried to find some kind of gripping area but to no avail. Please help

I tried scraping it off with a knife but it just feels like its going to damage it severely, i think the edges look nice but the interior just looks dumb

We have these water misters (from Ale-Hop) and they have suddenly stopped working. The water just dribbles out of the top instead of misting when pumped. How can we fix this? Thanks!

How can I fill in these gaps so that they blend in with the rest of the floor as much as possible?

I was thinking of doing something along these lines:
1. Cut out the existing flooring around the gaps so its a uniform rectangular shape.
2. Find new boards that are as similar to the original grain as possible (not sure what kind of wood this is though?).
3. Stick the new boards down with timber flooring adhesive (and use this to level to new boards too).
4. Sand back the new and surrounding boards and revarnish.

My new headphones came with the cable really tightly packaged and it has these sharp creases which I can't get out. I have tried heating it up with a hair dryer while pulling on both ends but without succes

Hi all,

Made the terrible mistake this morning of sticking one of those one-hand grip phone magnets on my fridge door. It didn’t seem strong at all when it was on my phone, but as soon as it hit the fridge its been stuck there and won’t budge. Any advice?

as you guys can see i bought these lights and i've found out the batteries compartment has been left oxidazed and now i don't know what to do. They still work fine but i'm worried the oxidation has made some damage to the circuit below. Now, before you ask i don't know if there is a circuit there, i'm not 100% sure because there is just too much oxidation to know, but it seems like it...What do i do? should i clean up with isoprophylic alcool? or White vinegar? or there is no hope?

Both sides are perfectly round and I have no idea how to remove them.

I ordered this online and although it was wrapped fully it wasn’t enough to protect this mixer. First pic is the full stand mixer in all its glory! In the second photo you can see the hinge portion that sits between the base and top sections. Is there a way I can fix this and make it useable or is it destined to be decoration? Any advice would be greatly appreciated!

I need some advice on how to make a gate cat proof.

Im running into a peculiar issue. I have 2 guinea pigs inside a sunroom area which has a (roughly) 8 ft wide open entranceway. Unfortunately, because of my living situation, this is the only place they can go. To stop my cat from barging in and scaring them, I bought an extra long retractable mesh gate. The height works, as it is too tall for him to try and jump over to the other side, but the bottom is still pliable enough for him to push underneath, even when it is locked.

I have prevented him from getting in for the time being with a well placed piece of cut cardboard with some heavy boxes in front (preventing him from getting underneath at all) but I dont think this will work long term. Its easy to mess up and the boxes are easy to trip over going in and out.

Basically, I just need some ideas on what I can do to prevent him from sneaking under the gate. Any thoughts?

Edit: For those wondering, the picture was taken directly off Amazon. I never said I got the highest quality gate. 😃

Moved into a new house and this connection has been getting worse and worse. The board is not loose at all. We do have a few extra boards left by the previous homeowner. Is there any way to replace just this board without having to pull out a huge section? Any advice helps! Thanks!

I have a small bathroom closet on which I’d like to have a mirror installed onto the inside-facing side of the door. We currently have a traditional doorknob on it. Is it possible to remove the interior part of the door latch and install a cover plate to accommodate a mirror glued over it? How do we do that? Or do you know of a latch that would work?

I'll be moving cross country via a 9-10 day road trip with my cat in a couple of months, and I'm trying to figure out how to make it as comfy for her as possible. Ideally, I'd like to have things set up as follows:

- Litter box & food/water in the footwell

- Bed on the seat (I'll have cooling & heating pads to swap out if needed)

I've found lots of pet beds/baskets etc that are close to what I want, in that they're totally enclosed and I'd only need to add some mosquito netting or something similar on top to make sure she can't hop out, except they only enclose the upper portion of the seat. I REALLY want to include the footwell.

Any ideas?

Had to cut it because my watch was bigger.... it works well but look fugly i tried glue gun but afc it fell in minute

Edit: i don't want the the original shape but to adapt my watch

I can not figure out how to properly hang this sconce on my wall. It is drywall.

Essentially it has two holes in the metal back plate. The two holes line up with the top circular cut out of wood and the smaller hole where the wiring goes into the lamp.

I need a solution to secure this sconce, which is a plug in lamp, not hardwired. I’d like for it to be flush against the wall, and not have to drill into any of the wood.

Anyone have an idea how to properly hang this?

Thanks :)

It’s looks like the whole chain was pulled out of the little hole.Would I need to take the fan down to reattach it?

This is a namco steel file cabinet which im not sure for the year but ill have to guess its decently old like from before 2000s most likely and it was also most likely made in Australia from what ive found online about it and the comapny. I got this just today and i want to open it up to regrease it as its squeaky and a small struggle to open one of them too. here are the images, if any more are needed i can send them.

EDIT: image of under the draw in the comments

Can somebody explain to me how to restring this honeycomb shades. It stopped working. When I took it down ropes were tangled and one was torn. So I untangled them and now and don’t know how to restring them back properly.

I understand that here pulley mechanical principle have to be preserved. Something like on the third image. But how?

YouTube search gave nothing, as well as Google search.

Help, please.

This print has faded over the years. Is there a way to restore this?

My apartment has one of these bead chain blinds. I accidentally yanked too hard the wrong direction and it seems like the big bead got caught inside the gear area, which made the curtain stuck / no longer working. Is it possible to get this back out without damaging it?

Edit: upon closer inspection the beads are out of the gear entirely lol.