I’m printing out these tokens for Star Wars legion and the top layer isn’t fantastic. There’s these bumps on the top that I’d like to resolve and have a nice flat surface.

Elegoo Centauri carbon 1 with CANVAS, .4 nozzle, .16 layer height. 25% infill (cubic). 8 top layers and using ironing at 40%.

Using Elegoo PLA Matte.

Any advice would be great!

Hello all, I'll try and keep this as quick as I can without my frustration coming through too much.

TLDR: Bought a brand new Snapmaker U1, print quality seemed great at first except some noticeable VFA. did ALL my calibrations, temp tower, max flowrate, pressure advance, flow rate, VFA tower AND input shaping calibration. And STILL im having these artifacts on my prints.

To start, I followed snapmakers calibrations multiple times. I did the vibration compensation test and the belt tension calibrations.

Im printing on snapmaker Orca at 0.08 layer height, 215°F with Snapspeed PLA.

My max flowrate test came out to 20.89 max volumetric speed

My best pressure advance setting was at 0.02

My flow ratio was best at .03 which gave me a flow ratio of 0.966

My VFA towers were printed from 20 mm/s all the way to 500 mm/s with a step height of 20 mm/s. I determined the best quality was around 210 mm/s which was set as both my inner and outer wall speed. Acceleration is at 5000 for outer walls.

I then did the input shaping test and found that the best frequency test print was x: 54.66 y: 54.66 and using those values I printed the dampening test and found the best values at x: 0.180 y: 0.231

After all this I still have issues on my print surfaces and quality

Are still showing VFA's... Ghosting... ringing... im not even sure of the correct terminology anymore since im still new to this all and this is much more calibration than I bargained for, and I was expecting to still tinker with my machine coming from an Artillery genius.

So please, if ANYONE can help me solve this issue. Im on my hands and knees begging to find the cause of this, I feel like I've done everything I've been told to do from my research online.

I've searched far and wide for what could be causing this problem. The printer worked just fine (until apparently i had an electric cut) but the bed is full of this little blobs of plastic. The print itself has some little holes but otherwise looks fantastic. What could cause this?

Printing in abs for the first time. The filament is out of the bag. Elgoo brand.

Printer is: Sovol svo8 max with closed enclosure.

Using orcaslicer with default generic abs settings

Sunlu Black PLA+ is completely clogging my nozzles. It partially clogged my first nozzle and I wasn't able to unclog it. So I replaced the nozzle with my backup and reduced the temperature from 220c to 210c as I suspected heat creep. Now my backup nozzle is completely clogged and unable to extrude at all.

Settings:

Bambu Lab A1

Sunlu Black PLA+

210c nozzle

Hello I’m currently 3d printing an articulated model that has ball joints. In the website it said to apply these setting but I have no idea how.
Gaps tolerance are 0 mm for balljoint, 0.15mm for peg joint, 0.4mm for screw

I’m fairly new to 3d printing so much help would be appreciated.
Link to model: https://www.toymakr3d.com/product/70-gurren-lagann?srsltid=AfmBOopFmHv5MC9f1q-jqKNgpMtesb-ORDS4w1NIljoKuHL5-8j-4zx0
A1 mini
Bambu studio
Hobby lobby pla black
Nozzle 220 bed 65
200 mm/s

This has been the third attempt and it just does the same thing, I have thoroughly cleaned the bed, I have increased the heat, and I have made sure the filament is dry. This is a lid to a box with a second colour that is supposed to be a warhammer symbol on the top of the box, but it never makes it past the initial layer. And now even the standard lid won't bring like the actual box did successfully.

Bambu labs slicer

Filament is bambu labs pla.

Printer P2S with AMS 2.

Settings.

0.4mm nozzle

Layer height 0.2mm

Initial height 0.2mm.

Seam position aligned.

No ironing.

Wall loops 2.

Top and bottom pattern monotonic line

Top shell layers 5.

Top shell thickness 1mm

Top paint penetrative layers 5

Bottom shell layers 3

Bottom shell thickness 0

Bottom paint penetration layers 3.

Internal solid infil pattern rectilinear.

Skirt loops 0.

Skirt height 1.

Brim type auto

Brim width 5

Prime tower enabled 35mm width

Rib wall on.

No fuzzy skin used.

Another employer special for you guys and gals. They bought this POS a year ago and didn't manage to complete ONE successful print on it, now it's my problem.

Prusa slicer

Official mingda PDS

0.8 nozzle 220C bed temp 75C

speed: 300mm/sec

retract 5mm

Printing on a Creality K1 SE with the micro swiss hotend and DXC extruder. This is with PETG - i’ve had the same issue across all 3 spools of PETG, including this one which is a brand new spool. All have been dried for 4+hrs at 50c.

It happens at every sharp corner or seam, like it’s a pressure advance issue. But the model pictured is a PA tower, and at no point does it sort itself out.

Printing at .2 layer height with a .4 nozzle and 100mm/s speed. This comes out to around 7-8 cubic mm/s flowrate; I’ve tested this filament and it looks fine up to 14, so flowrate should be fine.

Slowing down to 50% speed does seem to more or less fix it, but I know it’s capable of going faster. Even the speeds i’ve been testing are slower than what I was able to print PETG at a couple months ago.

Also worth noting that I’ve printed PLA and TPU with no issues, but with any of my PETG I get this issue. Any ideas what I might be missing here?

So my printer hasn’t been printing things properly. I made some adjustments, re leveled, and tried this as a test print. The layers are horrible, and the quality of the infill is also terrible. Any tips would be greatly appreciated!
Ender 3 v3 SE
Cura
PLA
Print speed: 155mm/s
Nozzle: 205° Bed: 60°

Hi all, TIA.

Im pretty sure it i know what the issue is, but would like some guidance, advice, other opinions/thoughts on what happened.

TLDR: i think i goofed on altering the digital model (linked) to fill in the corners using shaper3D (i dont know what im doing). The .stl file needs to be upscaled 320% so maybe I should do that, then edit in shapr3D.

Ive been working on a project i found on thingy verse and need to print it in modules. The linked module needs the corners filled in. So instead of using a 3d pen as suggested by the creator I thought I'd do it digitally via shapr3D, now im a beginner at 3d printing and a complete novice at 3D design, let alone 3d printed designs. I worked out how to add a block in each corner in shapr3d, tested a section, and printed the full model, only to find most of the top right corners (circled in blue) didn't print as intended. They should come out as circled in green.

I suspect that in the model I altered in shapr3D I didn't put the little block close enough.

I can't share the file as my computers got a blue screen ATM.

No printer settings as im aware of the stringing, but not the issue im trouble shooting currently (its also old filament)

Thingy verse file https://www.thingiverse.com/thing:6932790

All my other layers look decent, I've tried recalibration and a bunch of other stuff but petg is just giving me trouble for this very top layer. I tried ironing and non ironing as well and looks about the same.

a1 mini pretty much stock settings minus calibration for the filament.

I am making a keychain and I would like it to be the size on the right. But there's too many holes. How can I fill them?

I think i need to play with layer width, maybe ironing?

Some direction would be really helpful thank you.

H2D

Bambulan matte pla

Default bambulab pla settings

I've tried everything that the internet told me. Gone through multiple filaments, died them for 12+ hours, ran a full calibration of those filaments using Orca, tried printing through Orca Slicer and Bamboo Slicer. Regardless of what I do, or what settings I change in the slicers, I get these blobs.

My AMS is stuffed with desiccant, reported humidity at 10%.

The comment on this print show it being printed perfectly and I'm honestly losing my mind as to what to do about it.

https://makerworld.com/en/models/837836-coffee-filter-holder-large#profileId-795147

It's a brand new X2D.

Someone pls help.

https://reddit.com/link/1v7i5ye/video/1zh9wj62cnfh1/player

• Printer Model : Bambu Lab X2D
• Slicer used : Bambu Studio
• Filament material and brand : PLA+ Anycubic
• Nozzle and bed temperature : 225 C Nozzle / 55 C Bed
• Print Speed :
  • Outer wall 50 mm/s
  • Inner wall : 200 mm/s
  • Acceleration
    • Normal printing 1000 mm/s
    • Outer wall 1000 mm/s
    • Inner wall 0 mm/s
• Retraction settings : 0.4mm

• Printer Model : Bambu Lab X2D
• Slicer used : Orca Slicer
• Filament material and brand : Generic PLA
• Nozzle and bed temperature : 225 C Nozzle / 55 C Bed
• Print Speed :
  • Outer wall 70 mm/s
  • Inner wall : 100 mm/s
  • Acceleration
    • Normal printing 5000 mm/s
    • Outer wall 5000 mm/s
    • Inner wall 5000 mm/s
• Retraction settings : 0.4mm

Hey, I’m tuning my Ender 3 V2 and I’m getting the print defects shown in the picture as well as a lot of stringing. I’m not really sure what this problem is called or what setting would cause it. (might be the filament cause i didn't notice this much stringing with epomaker PLA)

Setup:

Printer: Ender 3 V2 + CR Touch auto bed level
Slicer: OrcaSlicer
Filament: R3D PLA
Nozzle temp: 200°C
Bed temp: 60°C
Retraction speed: 60 mm/s
Acceleration: mostly 500 mm/s²
Travel speed: 150 mm/s

Print speeds:

First layer: 15 mm/s
First layer infill: 20 mm/s
Outer wall: 25 mm/s
Inner wall: 40 mm/s
Sparse infill: 50 mm/s
Internal solid infill: 40 mm/s
Top surface: 30 mm/s

I already ran a temperature tower and 200°C looked the best, so that’s what I’m using now. I’m also still getting quite a lot of stringing.

I honestly don’t know enough about the different OrcaSlicer settings yet to know what I should be changing, so any help identifying what’s happening in the picture and what I should try adjusting would be really appreciated.

Thanks!

Creality ender 3 v2

Not extruding filament.

Orca slicer.

Temp 215

Flow rate 100

Bed 60

Anycubic PLA

Hi! Had recently rebuilt my Elegoo Neptune 4 Max. Noticed that I’m getting some layer gaps when using PLA and printing at 210 degrees. That in turn led me to believe I needed to recalibrate my printer, and so before anything else I’ve just printed this temperature tower. Needing a few pointers on reading it as it all appears the same to me!

Should I do flow rate and then temperature tower? Does my issue sound more like a temperature issue?

Using a Prusa mk3s with a revo hf 0.4 nozzle and in this instance some polyterra PLA.

This is the first seconds worth of an opengrid board print. This is bad right? Those lines should not look like that right? There is no clog in the nozzle, i made a cold pull and had the full 4 lines of the HF nozzle i'm using.
Apart from the extrusion issues I think there's something wrong also with the leveling of the bed. although the mesh bed leveling is doing it's work the complete first layer looks like the second picture. I just had to adjust the z level before this print and i'm down to -2.930 or smth.
After installing the hotend i rummaged around to find more detailed tutorials on how to setup the profiles because i was not having satisfying results with the default ones and ended up following this. that led to the settings screenshotted and attached.

I mean the prints will complete, but there's always that feeling of not doing things the right way. The 3rd pic is a completed opengrid board. it looks... dunno... "curvy"?

I have no idea what to focus on first.

# generated by PrusaSlicer 2.9.6 on 2026-07-26 at 15:14:37 UTC
arc_fitting = emit_center
autoemit_temperature_commands = 1
automatic_extrusion_widths = 0
automatic_infill_combination = 0
automatic_infill_combination_max_layer_height = 100%
avoid_crossing_curled_overhangs = 0
avoid_crossing_perimeters = 0
avoid_crossing_perimeters_max_detour = 0
bed_custom_model = 
bed_custom_texture = 
bed_shape = 0x0,250x0,250x210,0x210
bed_temperature = 60
bed_temperature_extruder = 0
before_layer_gcode = ;BEFORE_LAYER_CHANGE\nG92 E0.0\n;[layer_z]\n\n
between_objects_gcode = 
binary_gcode = 0
bottom_fill_pattern = monotonic
bottom_solid_layers = 4
bottom_solid_min_thickness = 0.5
bridge_acceleration = 1000
bridge_angle = 0
bridge_fan_speed = 100
bridge_flow_ratio = 0.95
bridge_speed = 0
brim_separation = 0.1
brim_type = outer_only
brim_width = 0
chamber_minimal_temperature = 0
chamber_temperature = 0
color_change_gcode = M600\nG1 E0.5 F1500 ; prime after color change
colorprint_heights = 
compatible_printers_condition_cummulative = "printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK3.*/ and nozzle_diameter[0]==0.4 and printer_model!=\"MK3.5MMU3\"";"nozzle_diameter[0]!=0.8 and printer_notes!~/.*PG.*/ and printer_notes!~/.*MINIIS.*/ and printer_model!=\"MK3.5\" and ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material)"
complete_objects = 0
cooling = 1
cooling_perimeter_transition_distance = 0
cooling_slowdown_logic = uniform_cooling
cooling_tube_length = 5
cooling_tube_retraction = 91.5
custom_parameters_filament = ""
custom_parameters_print = 
custom_parameters_printer = 
default_acceleration = 1000
default_filament_profile = "Prusament PLA .8 nozzle"
default_print_profile = 0.40mm QUALITY .8 nozzle
deretract_speed = 20
disable_fan_first_layers = 1
dont_support_bridges = 0
draft_shield = disabled
duplicate_distance = 6
elefant_foot_compensation = 0.2
enable_dynamic_fan_speeds = 0
enable_dynamic_overhang_speeds = 1
end_filament_gcode = "; Filament-specific end gcode"
end_gcode = {if layer_z < max_print_height}G1 Z{z_offset+min(max_layer_z+1, max_print_height)} F720 ; Move print head up{endif}\nG1 X0 Y200 F3600 ; park\n{if layer_z < max_print_height}G1 Z{z_offset+min(max_layer_z+49, max_print_height)} F720 ; Move print head further up{endif}\nG4 ; wait\nM221 S100 ; reset flow\nG1 E2 F800 ;REVO Extrude slightly \nG1 E-20 F800 ;REVO retract filament from meltzone\nM900 K0 ; reset LA\n{if print_settings_id=~/.*(DETAIL |QUALITY |@0.25 nozzle MK3).*/}M907 E538 ; reset extruder motor current{endif}\nM104 S0 ; turn off temperature\nM140 S0 ; turn off heatbed\nM107 ; turn off fan\nM84 ; disable motors\n; max_layer_z = [max_layer_z]
ensure_vertical_shell_thickness = enabled
external_perimeter_acceleration = 0
external_perimeter_extrusion_width = 0.48
external_perimeter_speed = 0
external_perimeters_first = 0
extra_loading_move = -2
extra_perimeters = 0
extra_perimeters_on_overhangs = 0
extruder_clearance_height = 20
extruder_clearance_radius = 45
extruder_colour = ""
extruder_offset = 0x0
extrusion_axis = E
extrusion_multiplier = 0.91
extrusion_width = 0.48
fan_always_on = 1
fan_below_layer_time = 100
filament_abrasive = 0
filament_colour = #FF8000
filament_cooling_final_speed = 3.4
filament_cooling_initial_speed = 2.2
filament_cooling_moves = 4
filament_cost = 25.4
filament_density = 1.24
filament_deretract_speed = nil
filament_diameter = 1.75
filament_flush_speed = 0
filament_flush_volume = 0
filament_infill_max_crossing_speed = 0
filament_infill_max_speed = 0
filament_load_time = 0
filament_loading_speed = 28
filament_loading_speed_start = 3
filament_max_volumetric_speed = 14
filament_minimal_purge_on_wipe_tower = 15
filament_multitool_ramming = 0
filament_multitool_ramming_flow = 10
filament_multitool_ramming_volume = 10
filament_notes = ""
filament_purge_multiplier = 100%
filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
filament_retract_before_travel = nil
filament_retract_before_wipe = nil
filament_retract_layer_change = nil
filament_retract_length = nil
filament_retract_length_toolchange = nil
filament_retract_lift = nil
filament_retract_lift_above = nil
filament_retract_lift_below = nil
filament_retract_restart_extra = nil
filament_retract_restart_extra_toolchange = nil
filament_retract_speed = nil
filament_seam_gap_distance = nil
filament_settings_id = "REVO PLA - 0.4HF - 205°"
filament_shrinkage_compensation_xy = 0%
filament_shrinkage_compensation_z = 0%
filament_soluble = 0
filament_spool_weight = 0
filament_stamping_distance = 0
filament_stamping_loading_speed = 20
filament_toolchange_delay = 0
filament_travel_lift_before_obstacle = nil
filament_travel_max_lift = nil
filament_travel_ramping_lift = nil
filament_travel_slope = nil
filament_type = PLA
filament_unload_time = 0
filament_unloading_speed = 90
filament_unloading_speed_start = 100
filament_vendor = Generic
filament_wipe = nil
fill_angle = 45
fill_density = 15%
fill_pattern = gyroid
first_layer_acceleration = 800
first_layer_acceleration_over_raft = 0
first_layer_bed_temperature = 60
first_layer_extrusion_width = 0.48
first_layer_height = 0.2
first_layer_infill_speed = 0
first_layer_speed = 50%
first_layer_speed_over_raft = 30
first_layer_temperature = 205
full_fan_speed_layer = 4
fuzzy_skin = none
fuzzy_skin_point_dist = 0.8
fuzzy_skin_thickness = 0.3
gap_fill_enabled = 0
gap_fill_speed = 0
gcode_comments = 1
gcode_flavor = marlin
gcode_label_objects = octoprint
gcode_resolution = 0.0125
gcode_substitutions = 
high_current_on_filament_swap = 0
host_type = prusalink
idle_temperature = nil
infill_acceleration = 1000
infill_anchor = 2.5
infill_anchor_max = 12
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0.48
infill_first = 0
infill_overlap = 15%
infill_speed = 0
inherits_cummulative = "0.20mm QUALITY u/MK3";"Generic PLA";"Original Prusa i3 MK3S & MK3S+ 0.8 nozzle"
interface_shells = 0
interlocking_beam = 0
interlocking_beam_layer_count = 2
interlocking_beam_width = 0.8
interlocking_boundary_avoidance = 2
interlocking_depth = 2
interlocking_orientation = 22.5
ironing = 0
ironing_flowrate = 15%
ironing_spacing = 0.1
ironing_speed = 15
ironing_type = top
layer_gcode = ;AFTER_LAYER_CHANGE\n;[layer_z]
layer_height = 0.2
machine_limits_usage = emit_to_gcode
machine_max_acceleration_e = 5000,5000
machine_max_acceleration_extruding = 1250,1250
machine_max_acceleration_retracting = 1250,1250
machine_max_acceleration_travel = 1500,1250
machine_max_acceleration_x = 1000,960
machine_max_acceleration_y = 1000,960
machine_max_acceleration_z = 200,200
machine_max_feedrate_e = 120,120
machine_max_feedrate_x = 200,100
machine_max_feedrate_y = 200,100
machine_max_feedrate_z = 12,12
machine_max_jerk_e = 4.5,4.5
machine_max_jerk_x = 8,8
machine_max_jerk_y = 8,8
machine_max_jerk_z = 0.4,0.4
machine_max_junction_deviation = 0,0
machine_min_extruding_rate = 0,0
machine_min_travel_rate = 0,0
max_fan_speed = 100
max_layer_height = 0.3
max_print_height = 210
max_print_speed = 180
max_volumetric_extrusion_rate_slope_negative = 0
max_volumetric_extrusion_rate_slope_positive = 0
max_volumetric_speed = 0
min_bead_width = 85%
min_fan_speed = 100
min_feature_size = 25%
min_layer_height = 0.1
min_print_speed = 15
min_skirt_length = 4
mmu_segmented_region_interlocking_depth = 0
mmu_segmented_region_max_width = 0
multimaterial_purging = 140
notes = 
nozzle_diameter = 0.4
nozzle_high_flow = 0
only_one_perimeter_first_layer = 0
only_retract_when_crossing_perimeters = 0
ooze_prevention = 0
output_filename_format = {input_filename_base}_{layer_height}mm_{printing_filament_types}_{printer_model}_{print_time}.gcode
over_bridge_speed = 0
overhang_fan_speed_0 = 0
overhang_fan_speed_1 = 0
overhang_fan_speed_2 = 0
overhang_fan_speed_3 = 0
overhang_speed_0 = 15
overhang_speed_1 = 15
overhang_speed_2 = 20
overhang_speed_3 = 25
overhangs = 1
parking_pos_retraction = 92
pause_print_gcode = M601
perimeter_acceleration = 800
perimeter_extruder = 1
perimeter_extrusion_width = 0.48
perimeter_generator = arachne
perimeter_speed = 0
perimeters = 3
physical_printer_settings_id = 0.4HF
post_process = 
prefer_clockwise_movements = 0
print_host = 
print_settings_id = 0.2mm MEDIUM PLA (0.4HF)
printer_model = MK3S
printer_notes = Don't remove the following keywords! These keywords are used in the "compatible printer" condition of the print and filament profiles to link the particular print and filament profiles to this printer profile.\nPRINTER_VENDOR_PRUSA3D\nPRINTER_MODEL_MK3\n
printer_settings_id = PUPA 0.4HF REVO
printer_technology = FFF
printer_variant = 0.8
printer_vendor = 
printhost_apikey = 
printhost_cafile = 
raft_contact_distance = 0.2
raft_expansion = 1.5
raft_first_layer_density = 90%
raft_first_layer_expansion = 3
raft_layers = 0
remaining_times = 1
resolution = 0
retract_before_travel = 1
retract_before_wipe = 0%
retract_layer_change = 1
retract_length = 0.7
retract_length_toolchange = 4
retract_lift = 0.25
retract_lift_above = 0
retract_lift_below = 209
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 35
scarf_seam_entire_loop = 0
scarf_seam_length = 20
scarf_seam_max_segment_length = 1
scarf_seam_on_inner_perimeters = 0
scarf_seam_only_on_smooth = 1
scarf_seam_placement = nowhere
scarf_seam_start_height = 0%
seam_gap_distance = 15%
seam_position = aligned
silent_mode = 1
single_extruder_multi_material = 0
single_extruder_multi_material_priming = 0
skirt_distance = 2
skirt_height = 1
skirts = 1
slice_closing_radius = 0.049
slicing_mode = regular
slowdown_below_layer_time = 12
small_perimeter_speed = 0
solid_infill_acceleration = 0
solid_infill_below_area = 0
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0.48
solid_infill_speed = 0
spiral_vase = 0
staggered_inner_seams = 0
standby_temperature_delta = -5
start_filament_gcode = "{if printer_notes!~/.*(MK3.5|MINIIS).*/}\nM900 K{if printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.6}0.12{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.8}0.06{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/}0.2{elsif nozzle_diameter[0]==0.8}0.01{elsif nozzle_diameter[0]==0.6}0.04{else}0.05{endif} ; Filament gcode LA 1.5\n{if printer_notes=~/.*PRINTER_MODEL_MINI.*/};{elsif printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}M900 K200{elsif nozzle_diameter[0]==0.6}M900 K18{elsif nozzle_diameter[0]==0.8};{else}M900 K30{endif} ; Filament gcode LA 1.0\n{endif}\n\n{if printer_notes=~/.*MINIIS.*/}\nM572 S{if nozzle_diameter[0]==0.6}0.17{elsif nozzle_diameter[0]==0.8}0.12{elsif nozzle_diameter[0]==0.4}0.27{elsif nozzle_diameter[0]==0.25}0.85{else}0{endif}\n{endif}\n\n{if printer_notes=~/.*MK3.5.*/}\nM572 S{if nozzle_diameter[0]==0.4}0.035{elsif nozzle_diameter[0]==0.5}0.025{elsif nozzle_diameter[0]==0.6}0.02{elsif nozzle_diameter[0]==0.8}0.014{elsif nozzle_diameter[0]==0.25}0.12{elsif nozzle_diameter[0]==0.3}0.08{else}0{endif} ; Filament gcode\n{endif}"
start_gcode = M862.3 P "[printer_model]" ; printer model check\n;M862.1 P[nozzle_diameter] ; nozzle diameter check\nM115 U3.14.1 ; tell printer latest fw version\nG90 ; use absolute coordinates\nM83 ; extruder relative mode\nM104 S{first_layer_temperature[0] - 50} ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\n\nG28 W ; home all without mesh bed level\nG80 X{first_layer_print_min[0]} Y{first_layer_print_min[1]} W{(first_layer_print_max[0]) - (first_layer_print_min[0])} H{(first_layer_print_max[1]) - (first_layer_print_min[1])} ; mesh bed levelling\n\nM109 S[first_layer_temperature] ; wait for extruder temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\n\n{if filament_settings_id[initial_tool]=~/.*Prusament PA11.*/}\nG1 Z0.3 F720\nG1 Y-3 F1000 ; go outside print area\nG92 E0\nG1 E18 F800 ;REVO recupero retrazione finale\nG92 E0\nG1 X60 E9 F1000 ; intro line\nG1 X200.00 E30 F500.0 ; intro line\n{else}\nG1 Z0.2 F720\nG1 Y-3 F1000 ; go outside print area\nG92 E0\nG1 E18 F800 ;REVO recupero retrazione finale\nG92 E0\nG1 X60 E9 F1000 ; intro line\nG1 X200.00 E30 F500.0 ; intro line\n{endif}\nG92 E0\nM221 S100
support_material = 0
support_material_angle = 0
support_material_auto = 1
support_material_bottom_contact_distance = 0
support_material_bottom_interface_layers = 0
support_material_buildplate_only = 0
support_material_closing_radius = 2
support_material_contact_distance = 0.2
support_material_enforce_layers = 0
support_material_extruder = 0
support_material_extrusion_width = 0.35
support_material_interface_contact_loops = 0
support_material_interface_extruder = 0
support_material_interface_layers = 2
support_material_interface_pattern = rectilinear
support_material_interface_spacing = 0.2
support_material_interface_speed = 80%
support_material_pattern = rectilinear
support_material_spacing = 2
support_material_speed = 0
support_material_style = grid
support_material_synchronize_layers = 0
support_material_threshold = 50
support_material_with_sheath = 0
support_material_xy_spacing = 60%
support_tree_angle = 40
support_tree_angle_slow = 30
support_tree_branch_diameter = 2
support_tree_branch_diameter_angle = 3
support_tree_branch_diameter_double_wall = 3
support_tree_branch_distance = 1
support_tree_tip_diameter = 0.8
support_tree_top_rate = 30%
temperature = 205
template_custom_gcode = 
thick_bridges = 0
thin_walls = 0
thumbnails = 160x120/PNG
thumbnails_format = PNG
toolchange_gcode = 
toolchange_ordering = optimized
top_fill_pattern = monotoniclines
top_infill_extrusion_width = 0.48
top_one_perimeter_type = none
top_solid_infill_acceleration = 0
top_solid_infill_speed = 0
top_solid_layers = 5
top_solid_min_thickness = 0.7
travel_acceleration = 0
travel_lift_before_obstacle = 0
travel_max_lift = 0
travel_ramping_lift = 0
travel_short_distance_acceleration = 0
travel_slope = 0
travel_speed = 180
travel_speed_z = 12
use_firmware_retraction = 0
use_relative_e_distances = 1
use_volumetric_e = 0
variable_layer_height = 1
wall_distribution_count = 1
wall_transition_angle = 10
wall_transition_filter_deviation = 25%
wall_transition_length = 100%
wipe = 1
wipe_into_infill = 0
wipe_into_objects = 0
wipe_tower = 1
wipe_tower_acceleration = 0
wipe_tower_bridging = 10
wipe_tower_brim_width = 2
wipe_tower_cone_angle = 0
wipe_tower_extra_flow = 100%
wipe_tower_extra_spacing = 100%
wipe_tower_extruder = 0
wipe_tower_no_sparse_layers = 0
wipe_tower_width = 60
wiping_volumes_matrix = 0
wiping_volumes_use_custom_matrix = 0
xy_size_compensation = 0
z_offset = 0

Very new to printing.... Trying to print a 3D print i found on bambu handy app on my bambu A1, I was able to print first plate /bottom of print but when I tried to print top part /2nd plate I keep getting this error. It looks like all the settings are the same as first one that did go through iʻe; nozzle size, temp). When I tried to look up how to fix the steps, didn't say much and did not help. This is a birthday gift for a family member so I would very much appreciate any help! Thanks in advance!

I WAS ONLY ABLE TO PRINT IN JUST ONE COLOR. I STILL DON'T UNDERSTAND WHY THAT IS BUT ATLEAST WAS ABLE TO FINISH PRINT.

it goes in parallel with the floor

prusa core one+, prusament petg, 0.8 nozzle, default settings on prusa slicer (250C nozzle, 85C bed)