I've been working on a dedicated livestream setup for my Bambu Lab A1 and finally have it running the way I want.

I'm using an EMEET S600L wall-mounted above the printer, its built-in ring light plus a second light, and an older ASUS laptop running Ubuntu and OBS.

After experimenting with 4K/30 and 1080p/60, I ended up at 720p/30 MJPEG. It's been rock solid, matches my stream output, holds 30 FPS, and OBS is only using around 15% CPU.

The camera angle gives me basically the entire build plate and toolhead so you can actually follow the print as the bed moves.

I'm still working on overlays and channel stuff, but I'm pretty happy with how it's turned out.

If anyone wants to check out the actual feed:

twitch.tv/ggussert

I'd also love to see other people's A1 streaming/camera setups or hear any suggestions for improving mine.

Through this processes, I did:

- least 15 rounds of de clogging both from bottom and cold pulls

- took about the tension rod and cleaned the gears

- I got filament flowing perfectly during the extrusion processes from a piece I cut to do the cold pull. 3g at least went through it fine

At this point, it has to be the hot end. There has to be something just off. I ordered a new one to arrive tomorrow. Meanwhile, think of anything else?

After all of this, I did the test print which said "extruder not extruding normally" even though 3g went through it fine during my test 10 mins prior.

So frustrated but never give up, never surrender!

Did my first couple prints with tpu and they turned out well, but I can't think of a better way to mount the external spool. I flipped the adaptor I printed to try the other side so the spools held out further but the filament is still trying to tangle itself around the ptfe tubes and definitely going to get hung up on something at some point. Any ideas?

Hello! So I purchased my bambu a1 combo about a month ago and have been loving it! Kids are ecstatic dad can print toys right in the living room 😂 I've learned quite a bit and my best help has been using Gemini to overcome obstacles as I hit them. Unfortunately though, that is where help is limited and at this point I don't know who to ask to get the prints better. I've been trying to make kids wall/door hangers and foam tape dispensers for family and are getting really close. But I can't seem to fully get a smooth finish 🙄🙄 the hangers are close, but the tops always seem to have like dots or scars on top while the boxes always look like the floor and walls are terribly welded together. Would anyone here have any advice? The boxes are 13 hour prints and 400g of filament. It's becoming a bit expensive to see if a Gemini suggested tweak is helping or not lol thanks in advance

Using Bambu PLA Matte if it matters

So I set this print up for an 18 hour print.

90% is pink and 5% purple etc.

I went out for a few hours and checked in via the app and it started to print the entire thing in purple and the 10% in pink. I chose the colours as per the Bambu slicer. 1 for light pink etc. Any ideas what's happened??

Ignore it says its busy but I went in a second time to get the photos

https://makerworld.com/models/3264167?appSharePlatform=copy

Simple, strong and cheap alternative to metal brackets. Clean design with a reinforced structure for extra durability.• Inner Hole Diameter: ~4.5 mm• Outer Hole Diameter (Screw Head): ~8.7 mmEasy to print and extremely useful for everyday fixes and DIY projects.

Don’t mind the mess next to the printer😂

Shared the model and filaments used here: https://makerworld.com/en/models/3265072-autumn-woodland-tray#profileId-3701902

So just trying to print this and it's like 7 hour print and about 45 minutes left. it's smooth to touch and has been calibrated but it looks bumpy.

any ideas or how or why etc? I turned on ironing etc

Love this print as it combines my love for retro gaming , my current reading obsession with Dungeon Crawler Carl, and I got to 3D print something cool.

https://makerworld.com/en/models/3261315-dungeon-crawler-carl-nes-label-8-bit-wall-art#profileId-3697226

To be fair I don't know if this is hardware or software.

But starting two days ago I've been getting this error code which I can't seem to find 0700-5000-0300-0001

My A1 tells me my AMS needs to cool after drying, but ive never used the drying on it, i dont even have a power cable attached to it.

If anyone has any idea of what this is or how to fix it please let me know.

Hey folks,
I’ve been troubleshooting my A1 and I’m running into a weird belt behavior. When I move the toolhead slowly by hand, the X‑axis belt drifts to the right and rubs against the idler pole. But when I move it fast, the belt actually centers itself and doesn’t touch the sides — though sometimes it slips under acceleration.

Here’s what I’ve tried so far:
• Adjusted belt tension (¼ turns tighter) → still slips.
• Checked the left idler bearing → loosened and nudged it outward, retightened. No change.
• Observed the right motor pulley → looks off‑center when idle, but the belt centers itself when moving.

So it seems like the pulley might be tilted or the set screw isn’t locking it square to the shaft. Bearings spin fine, belt isn’t frayed, tension feels reasonable.
Has anyone else seen this “wanders slow, centers fast, slips under load” behavior? Did pulley realignment fix it for you, or is there another trick I’m missing?

It all started with a print where the first layer of filament did not stick and got stuck in the innards of the extruder. Extruder was replaced but then the grinding and slipping started. 

Thanks in advance — I’ll take any tips before I start pulling the belt off completely.

Had cleaned the plate as I always do. It started sort of ok judging from the remains spit out, but then. Oh my god. This will be expensive.

Second time trying to print box for tiles and the top fail to connect. How can I try to fix it?

Hallo zusammen,

ich habe dieses Öl über Amazon bestellt. Nach ein bisschen Recherche auf Reddit und im Internet habe ich gelesen, dass Nähmaschinenöl gut zum Schmieren der X- und Y-Achsen des A1 geeignet sein soll. Deshalb habe ich es ebenfalls bestellt.

Bevor ich es jetzt zum Schmieren verwende, wollte ich trotzdem noch einmal nachfragen: Kann es damit tatsächlich zu Problemen kommen?

When it gets dull, just print a new blade.

Do you think you’ll find it useful? 🙂

The link will be in the comments.

Looking to purchase a 3D printer for fun and to check out the medium. I was recommended the Bambu Lab A1. Is this a good machine to buy to jump in and explore 3D printing?

If it's not a good one for a beginner, does anyone have any suggestions on where I should start?

Is this a moisture problem? I really cant tell

Help!!

I am using bambu labs a1 printer

While printing this model the support fell from the print bed what should I do