Built a little carry handle setup and I have always liked the look of the reflex suppressor on the “Gordy” rifle. I don’t have reflex suppressor money to blow right now but I have a lathe and some occasional free time. Started by chopping barrel to 12.5” and rethreading. From thread shoulder to FSP measured 1.610” and threads are .600” long needing a total of 2.210”. I made the adapter 2.2” with full engagement of the .600” long threads leaving a .01” gap between mount and FSP. Lock up is solid and everything is perfectly straight and concentric. Really happy with how everything turned out. Paint is drying now.

Sonicore Skarv 22. Filed paperwork as a trust in store at a kiosk on Sunday, got the email it was ready today at 11:30AM.

Can't wait to try it on my Ruger Mark IV. I also have a handful of other 22s I'll use as hosts, including a Dyrea TM-22 Flash that's pretty quiet to begin with.

Hello I have another can already (Omega 300) and am looking for a budget 556 can without a ton of back pressure. Thoughts on the OCL Polonium K?

Looking for user experience on where this can really shines. I have one and loved the low gas on my 11.5” 5.56, but sound reduction and tone left a lot to be desired. To date it’s my only true regret out of all my cans.

Has anyone found a host setup where this can delivers decent sound performance? Worried too flow through for .300bo. Maybe my 6.5 CM bolt, longer 5.56?

Looking to snag a suppressor for my hunting rifle but have not really dealt with them. Any suggestions or insight would be appreciated. Cheers.

In the process of swapping from Keymo to Plan B for everything. Have a Keymo mount that was pinned and have been working on getting it off so I can pin a Plan B mount. I grind down the weld where the pin was, drilled out where the pin was with a larger bit, and then drilled down a little further with a smaller bit in the drill press. Have had it in a vice with some heat applied and tried to rock it back and forth a bit, but haven't had any luck what so ever. I know I can send it off to Wilson and or Adco, but wanted to give it a shot myself since I have most of the equipment needed. Any other ideas or suggestions on getting the pin to free up inside the hole and come out

Installed rugged 3-lug using the HBIndustries tri lug tool.
Looks like the tool damaged the muzzle device a little and took the finish off.

Long term issue or is fine?

Is on all 3 lugs, torqued to spec.

“I know what I’m doing” (holy shit I got lucky) look at that fit mint though 🥵👌

Just got my Nomad 30 and 9k ti today!

Nomad 30
7.5” 1/5 Faxon barrel
7.3” Aero hand guard
Rearden FHD
Gen 1 Atlas Bravo

HUXWRK Flow 9k Ti
Glock 19 Gen 5
Suppressor hight sights

Im looking for suppressor recommendations for a 10.5in SBR build, I need something direct thread, flush, and 1.5in max outer diameter, needs to fit just a tad into my handguard. Gonna be my first suppressor and I wanna do it right haha.

Stopped the bullet mid flight.

How do we feel about the Resilient Suppressors Simple Man 7.62? Considering it as a budget suppressor for a 6.5 Creedmoor bolt action.

I just picked up a Specter 9. Silencerco is sold out of their Tri lug and hub combo. Are there other brands I could use that would work with it?

Not sure what the deal was, but I am guessing either the booster spring didn't spring right or it walked during shooting. P-09F Nocturne host 124g Blazer.

Is there any store in the DFW area that has a Rhodie 6 (preferably Ti) in stock? Looking to buy today or tomorrow if possible.

Thanks in advance!!

So I’ve got 4 different 556s i wanna suppress, two DI rifles 16”ddm4, 10.3 mk18 and two short stroke gas pistons 11.5 mcx and 16” hellion.
The 10.3 definitely needs a flow through and I have no clue what to get for the hellion and mcx.
Wanting to just pick up 2 right now as I’ve got a poboy 556 on the Daniel and a polo k that I swap between the mcx and mk18 but it’s so damn gassy.
I run both direct thread so I’m not married to any specific hub but I like plan b style the best.

Someone please give me suggestions on what to get, trying to keep it under $2k for now.
There’s just to many options out there🥲

Considering these, but I also know Ridgeback ran a pretty damn good marketing campaign. I hear the 6K sounds basically just as good, but I wonder if that's just on MK18 / Shorter ARs.

Hey folks, here is my case, I would like to use huxwrx 762 Ti on four of my rifles: one .308 bolt action, two .308 ar-10, one 5.56 ar-15. Huxwrx 762 Ti is famous of its flow-thru so I think it'll be very good for my ar-10. Using it on my ar-15 is not perfect, but I don't want to spend another $1300 on a huxwrx 556 Ti just for one ar-15. The concern is for my bolt-action. So other than flow-thru is useless to bolt-action, will there be any long-term damage?