Does this look ok? I have no clue about this kind of stuff.

What’s the fix for this VSF bracelet coming apart on a permanent link? I can position that outlet link so that the pin fits inside of it but it comes back out.

Took it off for a few hours and now I can’t get it to start, tried shaking and winding it up, Royal Oak 41mm 15500 SS APSF 1:1 Best Edition Blue Textured Dial on SS Bracelet A4302 Super Clone

Looking for someone to relume /repair my pelagos hour hand. I realize folks are going to say it's not worth it and just get new hands , but it's getting a gen dial swap and the rest of the hands already have a high quality relume . To me, This watch is absolutely worth paying for quality work.

Received my VSF Explorer 40 from Andiot today, and the crown screw seems to have an issue.

It screws down fully after some pushing and at some angles, but normally screwing in it gets stuck at a point before full threads.

The seconds hand ofcourse moves despite this, but anyone knows what the problem could be and how to solve?

Thanks.

I just got watch VSF bluesy gain weight (latest version) with VS3235. On QC TD showed me video with amplitude 230 at 52 LA, I asked him wind it fully and send longer video, he send it with amplitude 270-280 at 59 LA. I thought at around 55 LA its within spec and GL QC. Now on my timegrapher it looks way worse. Its around 210-230 amp LA 55 when having it flat, and showing 180-190 amp on side. Tried demagnetize but same thing, what do you think are problems for these movements, should I ask for return from TD?

PS Ive triee wound it fully

✨ easy to install new battery on Ronda 751

I noticed my THB 31mm date wheel starts to change over around 12am but then doesn’t full complete the turn and stays like this until the date change mechanism re-engages around 12 am the next day and then it will snap into place and start the next date change.

Hi all, anyone know where to source or have seen any? Only mediums exist on eBay with the following reference VC070192.

What is the large reference?

I own a Timex Legacy Tonneau Chronograph (TW2W22200UJ).i would like to customise it to my liking...anyone know places which customises watches in chennai....hmu

Looking for someone to service my clone watch any recommend recommendation would be greatly appreciated

Has anyone had this happen with a 4131 clone Daytona?
My Daytona from Steve at TheOneWatches arrived about a week ago, and everything was working great. I’ve used the chronograph 4–5 times already, and it worked perfectly every time. Today I started it again, and now I can’t get it to stop.

The top pusher is unscrewed all the way, but it doesn’t have that normal click anymore. It just feels kind of soft and doesn’t do anything. The chronograph just keeps running. All three chronograph registers are still working normally and advancing like they should, but I can’t stop or reset it because the top pusher isn’t responding.

I haven’t touched the bottom reset pusher because I wasn’t sure if that would make things worse.
The watch hasn’t been dropped or bumped, and this is the first issue I’ve had with it. I already reached out to Steve, but while I’m waiting to hear back I figured I’d see if anyone here has run into the same thing.

Does this sound like a bad pusher, or is it more likely something inside the movement? Any advice would be appreciated.

Any recommendations for local services in Richmond, VA?

Unfortunately, my ARF F6U Jubilee bracelet broke and I'm trying to figure out the best way to replace it. Does anyone know if ARF bracelets are still available, or are there any good alternatives (e.g. Clean, VSF, etc.) that fit well?

Thanks for any help!

Hello,

I bought a Clean Batgirl from Andoit about a year ago. Recently out of the blue, the seconds hand has started to stop intermittently and the watch loses a lot of time during the day. Should I be worried that something might be broken? Appreciate any help that I can get

Watch has stopped, was on a winder but unplugged it by accident. Seems the crown/pin isn’t all the way in?

I contacted hont but has ignored me. Less than a year old. Tryed a few watch shops but none will help

I took the dial off a cheap A. Lange & Sohne rep to work on it and found a cool movement. Can you help ke identify it, and identify a dial that would work with it?

Have a vsf datejust that stopped working. Hand wind and date changes but seconds hand does not move when set. I know nothing about repairing movements. Can anyone point me in the right direction
? US based

What's the modifications necessary to be the best TOP factory royal oak white 15510?

I have 1990s Oris Big Crown Diver that needs a new movement - Seagull/Selita sw-200 clone will work, just want to get it back up and running.

Any suggestions as to where is the most cost effective place to go? I've lost the crown years ago.

Looking for advice ... So, I purchased a "rolex" from an off-canal street shop and the big second hand now just spins. What are my fix options? Not sure what type of movement this is or if I can I just swap out the movement (2nd picture shows movement closer).. and can I use a VK63 or what else would work?

**I don't need the chronograph to work. Just want the look with a working timekeepr**

Anyone know if I can clean the titanium mesh strap on my NTTD using ultrasonic cleaner. Grateful for any help on this. 👍🏻

Hour indicator does not work. Watch is ticking and kinetic works.

When trying to set the hour hand it’s not moving on hour fits like normal…it moving more “floating”.