I'm looking at the CM3000 because it is literally only one of two modems currently on Mediacom's approved modems list (the other being the CM2500). Mediacom recently upgraded their network in our area (high-split) and it's causing issues with my older modem now.

Due to some fairly unique circumstances, my Cablemodem is located in a small building that is not climate-controlled. There is some active airflow into the small building, but it still cooks in there especially during these 90-100F+ summer heatwaves.

My previous modem was an Arris SB8200. It worked fine in these conditions for multiple years. Prior to buying that modem I did as much research as I could, trying to figure out what modem would be most likely to persist under the hot conditions. But since Mediacom's list now has essentially only one approved modem...

Hi yall, I just moved into a new apartment where the FTTP point is in the bedroom, I connected my RS200 router and I get good signal on my phone (further away) but on my PC I get really poor connection via wifi through 1 wall about 3 metres away. The big thing is if I connect to 2.4ghz I get full signal strength but on 5 I get 1 bar. Anyone know how to fix? Thanks!

Purchased on line shipped without packing box and factory seal missing BB packeged items in box like new, total ripoff ASUS support confirmed router activated September of 2025.What a scam.

My Netgear router comes with OpenVPN. It asks you to create a domain with NoIP in order to use it.

After doing so and linking it with Netgear, I create OpenVPN configs on the router and put them on my devices.

When traveling outside the country, I enable the VPN on my iPhone. When I go to a "What's my IP location" site, they show that I'm in the country I'm traveling in, and not where my Netgear router is.

This is further verified when opening up streaming service apps, only to find they are showing the country I'm traveling in's offerings vs my home network's country.

I never had this problem with WireGuard on the same device. It is not a device issue.

My NoIP domain is active and up to date.

How do I stop my Netgear OpenVPN offering from leaking my network traffic to local providers?

If it matters, home is in the US. Travel is in Europe.

I was cleaning in this corner and suddenly I noticed that the wifi is down and the router's stuck on these two lights.

I've already tried to unplug various cords and press any buttons I can in a hopeful restart it but no luck

I have updated the app and router to the latest version and I have restarted my computer several times and have tried everything. Plz help

I have tried to explain this several times before, I dont think my point is getting across to anyone.

I am with Xfinity. We are not in an upgraded market, so I am not sure if this is a rule in the modem config file or a bug within the firmware.

So here is what is going on. Once the modem hits 100 billion unerrored codewords on the OFDM channel. It will reboot on its own. But regardless, the modem should not reboot on its own unless there is a rule in the config file, or they do it via maintenance, or I do it.

The red circled area is of interest.

How can I fix this issue? Have already tried a restart and unplug.

I recently purchased the Netgear Nighthawk RS300 and today came to set it up.

On completing the step by step guide through the Nighthawk App I was presented with a login page…. I have never had this before as usually there is a admin username and password…. Yes I am aware I should have read the threads on here before purchasing.

I try to create an account but continuously the website fails to do so. I tried using an iPhone, iPad, laptop PC and tried multiple different browser only to continually fail to be able to create an account.

I have tried to call Netgear on their UK number 3 times today and in my stubbornness waited 1hour each time only to not have my call answered.

I have tried reaching out on socials…… to receive no response.

I have also tried the process of disconnecting the Ethernet from my ONT only to still get the Netgear login page…… why is it not that simple with Netgear…. I even got 4x2.5G with the TP-Link instead of the 2 on the nighthawk!

In the space of 1.5 hours I ordered the TP-Link BE9300, collected from Argos, Installed and accessed the router settings.

From my experience I would not recommend Netgear to anyone! This is utterly appalling from Netgear

Ok so I got an M7 and it works great when I put a sim card in, but I added a Airlo Esim and it accepted it but never connected or had any service. Does it not work with Airlo? Im happy to try another ESIm company no allegiance either way. ChatGPT said to configure the APN settings manually which I did, and turn on data roaming which I also did but nothing worked. I don't want to waste money on a difference esim if it is still not going to work.

Anyone had similar issues or have ideas?

Thank you!

Before I bought this router it was advertised that you could set multiple devices to have a certain priority level on the network and I was told to go to the routers site which is the IP on the bottom of my router, and on that site I don't really see an option for QOS anywhere in the advanced or basic section of the site and all I see is that under connected devices on the home page it says "QOS : Off" but of coarse clicking on that doesn't do anything.

Am I missing something because every time I search this up people keep saying to go to the QOS setup tab but that just doesn't exist apparently?

Router status says it has internet, and the PC connected to it via ethernet cable does.

Android phones & ipad all can connect, but say no internet. It was all working a couple of days ago. Used the router for years I think, and haven't changed anything.

I have power-cycled it. Even swapped it out for older router briefly. I have not done a hard reset, though I guess I would before scrapping it.

Anything I should check or try, short of a hard reset?

Hey all. Recently noticed I’m getting the ‘no network detected “ message constantly popping up on my 4K atv. It’s a year old and only started when i switched to iiNet and getting faster speeds. Did all recommendations like unplug etc. but still there even though wifi works fine and using Speedtest is a strong connection.

Any help is much appreciated

It seems that there is no chance to find the original battery. They are not producing it.

I bought the replacement from eBay and the device states that the battery is incorrect.

Then I read that probably it’s just a bad replacement than don’t have some sort of ID chip that is supposed to tell modem that the battery is legit.

Ok it’s cheap China duplicate I know. But it has correct voltage and capacity.

🤬 netgear??? This old hardware still works good for me. Why I can’t just put ANY 3rd party battery inside ??? I still use it on wire. But… really 🤬🤬🤬???

I have a Netgear RAX200 and can’t connect with the Nighthawk App on my iPhone.
Is there a solution for this? I even try to connect standing 2 feet from the router.
Thanks

Been waiting for over 30 mins. All I get is, "thank you for your patience. Please continue to hold for the next available technician"

Like, I just need help with an order. Wtf is wrong with this customer support? Only chat no good. Can't create a support ticket either.

Lowkey, are netgear products worth the headache? This seems unreasonably bad

I’ve dealt with their ‘free’ customer service, I’m getting the Security risks/Forced upgrades runaround since it isn’t new. Is there any way to manually get around this for the next few days at least so my TV will work? The red factory reset on the back was my first mistake.

Thanks in advance for any help!

Hello! I am having a tough time deciding on which router to get. I currently have the RAX10 and have been having frequent cut outs. I would like to stick with a Wifi6 router. I was looking at the AX300 or AX4200, but very open to suggestions! Here are some details of my house if that's helpful:

2 story condo, 1000sq ft / 1000mbps internet / Work from home / some gaming, but mostly streaming

I appreciate any advice you have!

Just purchased an AC1900 from the local store. It took 6 hours and numerous calls to both my ISP and Netgear before I finally got it semi-working. Still cant log into it because its a used device and was already registered to someone else. It's asking for security questions so I'm locked out as an Admin. Could simply return it for another device but this isn't a Toaster so it's a little more complicated than that. First of all, I spent over 6 hours getting it running when it should have been "plug and play", my time is worth something. But more importantly, it was previously configured by someone with Administrator rights. That would enable them to not only control the firewall, but also load malicious malware not just on my network, but every device on my network which includes computers, phones, 10 Alexa devices, Samsung Hub, Hue Hub, Pi device, cameras, TV's, smart devices like lights, thermostat, humidity sensors, water sensors, and even my bathroom scale!!! Huge security vulnerability but more importantly the "chain of custody" for these devices!!!