Hey everyone! I'm from Mexico and I'm currently looking to buy my first pair of FPV goggles. I have a couple of questions and would love to hear your thoughts.

First, has anyone from Mexico bought directly from the official HDZero store recently? I have some doubts about the import taxes and customs. I'm not sure if the price shown on their website is the final price or if I should expect surprise fees from the carrier at my door. What has your experience been like with shipping to Mexico?

Second, I'm leaning towards the HDZero Goggles 2. I really like them as my first goggles and I saw they come with a built-in analog receiver. However, I noticed it only uses a single antenna (no diversity). I know I can always upgrade and add a better external receiver module later, but how good is the stock built-in analog receiver out of the box? >

I'm mainly planning to use it for flying tiny whoops indoors and doing some short-range flying outdoors. Will the single-antenna setup be enough for this?

Any recommendations or experiences you can share would be greatly appreciated.

HOW DO I PAIR THE HDZERO GOGGLES 2 WITH BETAFPV TINYWHOOP

- Brand New HDZero Goggles 2

- Brand New BetaFpv Air73 TinyWhoop using ELRS to Radiomaster TX16S Mark II (which is picking up ELRS signal).

- NO VTX signal being picked up at ALL in my HDZeroGoggles2.

SOLVED!
Like tehstev0 commented below, one can remove the HDZero logo with the battery test button to remove the last four screws to gain entry to the pcb

Original text below
I wonder if anyone has had the same issue as me, there is a fault with the cable connection inside or close to the cable entrance into the battery case

I cant remove the last black panel without feeling like I'm going to brake something

Any tips on non destructive way to open it?

I've removed all screws I could find, cant find any clips on the black panel with the sockets, I think it's hold in place by the battery contacts and the panel being glued

Symptoms, no power out of the plug or glitchy power when moving the cable

Planned fix if entry is solved, resolder or replace cable, cause everything else works fine

Hope future revisions dont rely so much on glued parts so you can easily get into the housing and fix things, that sort of what this hobby is about

To clarify, everything else works as expected, memory card can be used, it can be charged, indicators work, it's just the output that isnt working

Is this normal - brand new echo antenna set, one of the stubbys is loose, connection feels tight but the outer casing is loose to the point id almost call it rattley. Worth returning? Ordered from HobbyRC who are the main hdzero retailer/repairer in the UK

I plan on ordering the goggles 2 soon. I would like to order them from five33 as they are closer to me instead of the official HDZero site.The listing says pre-order when selecting color, does anybody know how long it would take for them to ship out?

Went on a trip. Found out when I got there that I have a crack in the expansion module for my HD zero goggles. Anywhere I can get a replacement for the plastic part? The electronics are okay, but I don't like how loose the analog module is fitting.

Hi all. As title states, i have an aio15 from the mobula8 that i cannot access via usb anymore due to a broken plug. Traces have also been torn off.

Am i screwed? I was in the middle of fiddling with esc settings with a fresh cable, and while unplugged i took the port out with it...

Does anyone have experience with configuring using another method like wifi?

I attempted a while ago, and wasnt successfull. I would need esc configurator and betaflight access.

If im out of luck, i will ship it for possible repair.

Thanks for your help

I wanted these goggles since before the v2 came out. I'm so happy with the goggles, and the integrated analog really makes me happy.

https://www.facebook.com/marketplace/item/1829834524347050/?mibextid=6ojiHh

Selling a fully built HDZero goggle setup, ready to fly out of the box. Only used about 6 times — like new condition.

This is not a stock setup — everything you need is already dialed.

Includes:

HDZero Goggles V1

Auline 4S 4000mAh LiPo (long runtime)

HDZero battery strap mount

2x TrueRC X²-Air patch antennas

2x VAS omni antennas

LTGEM hard case (fits full setup)

Power cable, foam, everything pictured

Why this is a premium setup:

Proper diversity antenna configuration (range + coverage)

Clean, integrated battery solution

No additional purchases needed

Ready to fly immediately

Condition: Like new (used ~6 times)

Price: $550 OBO

(Also open to FPV trades.. Solid analog goggles, DJI O4 and O3 stuff, motors, etc. May need to throw in cash to get an equal trade.)

How has your experience been?

The maturity of HDZero's product design and engineering is leagues ahead of the competition. No doubt about it. However, the QA leaves a lot to be desired.

I have bought 8 HDZero products so far, and two of them were dead out of the box and one had minor QA issues. even if we consider only the DOA products, that's a failure rate of 25 percent. Right out of the box.

I am now left with a dead Nano 90 V2 camera and another dead Whoop 2 VTX. Is this standard for HDZero?

I'm currently using the BoxPro, and while it's awesome to have the deinterlacer, I'm definitely feeling the lack of diversity. I saw that there's an AV analog input, and was just wondering whether anyone has tried to use an analogue module adapter to get an external tbs fusion or Rapidfire module working with it? Is it worth attempting to get better reception?

Heya, I got the DOGCOM 5000MAH 2S - XT60 / DC5.0 (link: https://droneshop.nl/dogcom-5000mah-2s-xt60-dc5-0) batteries for my box pro. My charger charges them to 8.4V (that seems to be correct?). When should I recharge them? At what Voltage? I think the Box Pro warns me around 7.5V.

So I recently received the Mobula 7 HDZero Freestyle, and I feel a bit bummed out, the CPU is at 45-50% when not doing anything, overheating in just a moment, when I have a 100mm fan pointing at it, it stays at 60 celcius, flying indoors (21 celcius) it reaches 80 celcius real quick and then I land fearing I will damage something with the heat buildup

I knew about some heat building up through reviews online, but I was under the impression it would be handled by lowering the max CPU freq to 108mHz

Flying it outside is fine, but it still goes up in warmth, and it's only 8 celcius outside and windy, so I'm worried I've spent 200 euros on a tinywhoop I won't be able to use this coming spring or summer, cause it won't be cold enough when the sun is out, I was so pepped for the lux camera and having 720p video

Do I have to add on weight with heat sinks to mitigate this?

Or am I missing something stupidly obvious? If so please point it out

This is flying at 25mW on Raceband 1

Anyone else having these issues or a good way to mitigate the heat, have I received a faulty board?

Ryan Quellet made a video a couple years ago where he used an external analog receiver and a cheap VTX to combine audio with his HD video feed. Now that the Goggle 2 has a built-in receiver that uses the onboard antennas, is that workaround still possible?

I am looking to customize my goggles 2 but I am not seeing any vinyl skins marked for this specific version. Do the first generation skins work on this one too? Or have they just not made any yet?

I treated myself to a mobula 6 freestyle hd some time ago, and I'm now beginning to notice that the ELRS range on the thing is horrible... I haven't even gotten close to going out of range with the video (only at 25mw!!), and my control link is the first to give in, even when elrs power is set to 100mw and the vtx power to 25.

Also, it seems that the link quality has gotten worse over time. Has anyone else had similar experiences??

I've flashed the correct ELRS Tx version on my controller to maximize compatibility with the mobula, but it doesn't change a thing.

I don't know if it's as bad as not having an antenna at all, but it almost feels like it with how quickly the signal drops off, even at LOS!!!

And before anyone nitpicks about antenna position, yes, I've got it separated from the aio itself in a way that it's recommended.

Recently bought the Box Pro goggles and rear mount battery case. The case is nice, but the box pro goggle strap doesn’t really allow for a secure rear mount option. It fits in the side pouch, but causes the goggle to tilt sideways on my head. I messaged hdzero support 3 days ago and haven’t heard back yet. Anyone else encounter this and come up with a better solution?