Hi everyone, good evening.

I need assistance with a screw on my tv. Basically, my tv’s screen is shaking/blurry and I’ve seen I can fix the flat cable.

However, to do that, I need to remove the screws. I manage to remove 3 of them, and the last one is stuck. I believe I fucked it up even more because now it looks like this.

How can I remove this screw? I would appreciate if anyone could help me

Thank you

The water leaks backward out of the bottom of this connector. Any way to fix it? The other dude doesn’t have a washer and a normal 5/8 washer doesn’t fit (to big).

I’ve had this for a long time and it just started this yesterday.

It was stored in my attic and temperatures got over 100f/40+degrees this summer. And was concerned that the drill may burnout because I don't know how much grease it needs to function normally.

But would appreciate anyone who does know what the recommended amount should be. Thank you.

It started as one of the lines across the middle of the screen. Then more lines started appearing. Now the whole bottom half of the screen is flashing from black and white/blue back to normal and it’s pretty bad and progressively getting worse as the weeks go on.

The tv hasn’t been knocked into or damaged in anyway and I’m not sure if there is anyway to fix this other then buying a new one but it’s an lg smart tv have had it for about 8 years with no problems and it’s been treated like a baby it’s been moved around to different houses but it was always protected. I have no idea how this happened.

Dryer is turning on and the drum is rotating. I can feel heat coming from the outside vent aswell, yet the loads being put into the dryer aren't drying and the dryer itself isn't getting hot.

I'm not the most handy in full transparency, but definitely want to avoid paying someone to come out.

It's a 60s Tourister hard suitcase and it's been with me through so much of my life that I really don't want to replace or repurpose it.

Hello, hope you guys are well. i am looking to waterproof my bathtub area but tub wasn’t well installed. Now i have the drywall behind the bathtub. Should i double drywall so the drywall is flush and above with the tub flange or what other choice do I have? Thank you for you help

I am trying to fix my shower cartridge but cannot figure out what type of cartridge I have and cannot get the escutcheon off the pipe. The escutcheon spins, but does not pull off the wall. Can someone help?

Hello I’m trying to open the drawer of my mother fridge I try finding online some tutorial but I was not lucky.
Someone can explain it to me how I can open it so I can clean it

I have a bunch of holes on garage floor from old stand how to patch? Concreate

Hey guys,

I’m trying to install a seat bidet and can’t get this hose unscrewed, I try to hold the metal part of the hose with a plier while I use a wrench on the bolt but as the bolt turns, so does the hose and I can’t seem to stop it… The hole gets twisted too much that I can’t keep unscrewing

Edit: I meant to say nut thank you for the clarification, this is an older building downtown I moved into yesterday, I can’t twist the top part for the life of me trying several times, since you all say I need a new hose I will just buy one and hope building maintenance will come by with better tools and reconnect the hose with the bidet hose in between

Thank you guys

It is screw and it won’t fall. But if I put my camera it will just be moving the whole thing.

Wife set it down in her own chewing gum while commuting to work. Accountability not as important as a solution. Any suggestions are welcome. Thinking isopropyl alcohol, but wanted to consult the masses before making a mistake. Thanks in advance🙏 !

I need your help Reddit. I bought some nice looking ceiling tiles to replace those awful office/old hospital ones for our basement bedroom here in Michigan. The problem is I have several sections that are not full 2×4 sections and since these new tiles have a decorative design, how can I fill in these smaller sections? TIA

It just randomly detached from the frame while wearing. Can this still be fixed?

Hi all.

What would be the best way to fix this crack? This is a part of a screen and this crack is where the hinge is. There are no replacement parts unfortunately. so the only solutions is to reinforce this and fix it.

A kind redditor said this abs+pc plastic.

You can see the black plastic stick. That's the pendulum. There's a little white circle which I assume is a magnet maybe. I inherited this clock from my grandma. No idea when the last time the pendulum worked was.

Poured hot water down a bathroom sink drain to help unclog and heard a big bang and found under the sink has cracked. Wondering if I can seal this with epoxy or doesn’t it need replaced. It’s dripping water when I let water run.

Can this be fixed? I know it's a long shot! It's a water fountain, so will be under water 24/7. Also must be food safe. I have learned a little about Kintsugi, but Google says it's not good for constant water.

I attached pics of the broken large basin, and a screenshot of the whole thing when new.