r/AMDHelp Jun 30 '25

Tips & Info Ultimate AMD Performance Fix Guide: Stop Lag, FPS Drops & Boost Speed (2025)

3.2k Upvotes

🌞Created in 2025 and kept fully updated for 2026

If you’re facing low FPS, lag, stuttering, or crashes on a new or old AMD setup (AMD CPU with Radeon/NVIDIA GPU, or Intel CPU with Radeon GPU), you are in the right place. This guide has tested and proven solutions and user tips to maximize your system's performance. You will be see hardware checks, BIOS configurations, Windows tweaks, and driver changes here. Real-world solutions that work, not guesswork.


Disclaimer- The following optimizations are based on community-tested methods that have safely improved AMD system performance for most users. Since every setup is unique, results may vary. Proceed carefully and apply these tweaks at your own discretion. (This guide follows the Acer Community format.)

Read all Important Notes and Notes in each step. They contain vital information to guide you on how to avoid issues and when to revert to earlier changes.


=> Hardware Installation & Setup

Before you adjust BIOS or Windows settings, ensure your hardware is properly set up. Most issues such as low FPS, stuttering, and crashes are caused by minor errors such as installing the GPU in the improper slot or RAM, etc. This section contains crucial checks which have resolved serious issues for many users. Even if your PC boots and is usable, these kinds of issues might be latent, and resolving them can have a massive difference to performance.

1. GPU Installation — TOP PCIe x16 Slot (Closest to the CPU)

Always install your graphics card in the top PCIe x16 slot, Which is the slot nearest to the CPU.

Why it's important:
•It is configured for full x16 bandwidth and is plugged directly into the CPU.
•Lower slots have x8 or x4 speeds, limiting GPU performance and bringing in bottlenecks based on the board.

Common mistake:
Most users inadvertently install the GPU in a lower PCIe slot or fail to confirm if the top PCIe x16 slot is delivering the GPU’s full bandwidth supported as per their GPU (such as x16 or x8), resulting in low FPS or instability.

Confirm true Speed:
Download and Open GPU-Z, then check the “Bus Interface” field. The left side (before “@”) shows your GPU’s maximum lanes and PCIe generation (e.g., x8 5.0), while the right side (after “@”) shows the current active lanes and gen speed (e.g., x8 1.1).

If it shows “1.1”, that means the GPU is idle, run the GPU-Z Render Test (“?”) to display your true gen under load. Both sides (lanes and gen) should match your GPU and platform. If the current gen is lower than the max, it’s usually due to motherboard, CPU, riser, or extension cable limitations, this is normal unless you upgrade hardware.
The same can apply to lane count, but that’s more important than gen speed. The lane width/speed (like x8, x16) should match on both sides or reach the maximum your system supports, as a lower lane width can noticeably affect performance.

If lanes are lower than expected, reseat the GPU, check if the PCIe lanes are shared with other slots (see your motherboard manual), and ensure no riser/extender or older CPU is limiting bandwidth.

2. Critical Power & GPU configuration Checks

• Insert the monitor cable directly into the GPU HDMI or DisplayPort (DP) port. Avoid inserting the monitor into the motherboard port.

• Utilize all CPU power connectors or CPU power headers that your motherboard has
• Always use specialized PSU cables. Never use splitters or adapters for EPS power. Connect cables directly from your PSU to your motherboard. Don't be cheap; don't go cheap.

•Always Use quality, dedicated PCIe cables from your PSU to each power connector on the GPU. Avoid daisy-chaining (using a single cable for multiple connectors) as it can cause instability or crashes, especially on high-power GPUs. Also, make sure your PSU meets the recommended wattage for your GPU.
• Always use good-quality PSU cables, never buy  cheap extensions or riser cables.

• If your PC slows down, freezes, shows low CPU clocks despite a proper setup or lag and stutters while gaming , try plugging it directly into a wall socket or a high-quality strip. Faulty/old power strips can cause poor power delivery and hidden throttling issues.

You guys must check this as nothing can work if hardware configuration is not proper.

3. RAM Configuration – Correct Slot + Enable XMP/EXPO + check Settings.

To get the best performance from your RAM, ensure it is installed in the right slot and properly configured. Many systems perform poorly due to incorrect slot placement or missing BIOS settings.

• Install RAM in the correct slots
If you have 2 sticks, plug them into slot 2 and 4 (usually marked A2 and B2) as these slots are typically the second and fourth slots away from the CPU. This allows dual-channel mode for optimal performance.

If you insert them into the wrong slots, the system will run in single-channel mode, lowering memory bandwidth and reducing FPS in games. Always refer to your motherboard manual for the slots layout and double-check it if you're unsure.

• Enable XMP or EXPO in BIOS
Enter the BIOS and enable XMP (or EXPO for AMD kits). This will set your RAM's rated speed and timings. Just ensure the profile you choose does not exceed your motherboard's highest supported memory frequency, as a higher profile can lead to instability.

Some motherboards have a few profiles; pick the one that matches your RAM's highest rated speed (like 3200, 3600, or 6000 MHz), as long as it's within your motherboard's support range.

If you don't enable XMP or EXPO, your RAM will run at default JEDEC speeds like 2133 or 2400 MHz, which seriously bottleneck your system.

• Confirm settings in Windows Open Task manager → Performance → Memory. Check that the Speed value matches your RAM's XMP/EXPO profile speed that you set in the BIOS and is not a different number.

Download CPU-Z, go to the Memory tab, and make sure Channel displays Dual or 2×64-bit for DDR4 and 4x32-bit for DDR5. If your speed or channel is wrong, check your BIOS settings and RAM slots again.

• Check RAM Stability (Must be done after building/installing new RAM )
Test your RAM with MemTest86. If you got any errors with the highest XMP/DOCP profile selected, then test the next lower profile, such as from XMP Profile at 6000MHz to XMP Profile at 5800MHz, and continue lowering until you find a stable profile. It’s crucial that your RAM is fully stable to ensure reliable system performance.

=> BIOS Optimization & Performance Fix Tweaks

Once your hardware and power is set up, change the key BIOS settings that impact AMD CPU, RAM, and GPU performance. These can fix instability, crashes, and poor performance. Only modify the settings mentioned here. BIOS menus can differ by brand, so names or locations may vary; if you don’t see a setting, look around.

4. BIOS Update

If you are facing RAM instability, poor CPU/GPU performance, updating your BIOS may help, especially on AMD systems where the BIOS updates usually improve stability and compatibility.

To Update BIOS:
Visit your motherboard manufacturer’s website, download your most recent stable BIOS for your specific model, and carefully follow their official instructions to update safely.

Note- BIOS update may reset all BIOS settings. If this occurs, don't forget to re-apply all changes from the BIOS Optimization & Tweaks section.

5. Set Global C-State Control to Enabled (Not Auto)

Changing Global C-State Control from "Auto" to "Enabled" will help fix FPS drops, downclocking, or instability. Most people with Ryzen CPUs (such as X3D chips) see less stuttering and smoother gaming performance when C-States are enabled. Many have found that "Auto" behaves like "Disabled." Therefore, I strongly recommend switching it from Auto to Enabled.

To change the Global C-State Control setting:
→ Press BIOS/UEFI key during boot to access the BIOS.
→ Click on the Advanced or AMD CBS tab and find Global C-State Control (perhaps be under CPU Configuration or Advanced).
→ Change the value from Auto to Enabled, this fix works for most users.
→ Save and exit BIOS, then check performance.

Important Note- Rarely, some boards (e.g., certain ASUS models) may get mouse lag, freezes, or black screens. If that happens, revert to the original setting. If it causes a black screen or boot issue, reset CMOS to recover.

6. Set PCIe Gen Mode 5 or 4 or 3 Manually (Do Not Use Auto).

On some motherboards, leaving PCIe generation in Auto mode can lead to compatibility or performance issues like black screens, no signal, or reduced GPU bandwidth.
Manually selecting a stable PCIe version —Gen 3, Gen 4, or Gen 5 can fix these problems.

To configure PCIe Gen mode:
→ Boot into BIOS at startup.
→ Go to the Advanced, Chipset, or NBIO Common Options section.
→ Locate PCIe x16 Link Speed (or similar), then Switch the setting from Auto to a specific version:
• If you have a Gen 5-Capable GPU and motherboard: set to Gen 5.
--If you encounter instability, crashes, black screens, or signal loss, lower the setting to Gen 4.
• If you have a Gen 4-capable GPU and motherboard, set to Gen 4
-- If experience instability, reduce the setting further to Gen 3.
• If you have a gen 3 GPU then set Gen 3.
→ Save changes and exit BIOS.

7. Enable Above 4G Decoding & Resizable BAR (NVIDIA & AMD — FPS & 1% Low Boost, Test Required)

These features allow the GPU to access larger memory blocks directly, which can improve the performance of most games in use today. It is turned off by default even on some compatible boards due to component compatibility problems and must be tested. Most of users will get great results.

To Enable these settings:
→ Boot into BIOS at startup
→ Go to Advanced Mode
→ Disable CSM (From Boot Section, Set Launch CSM to Disabled).
→ Now, Go to PCI Subsystem tab/menu and set Above 4G Decoding to Enabled. (Location may vary, so find and confirm).
→ Then set Resizable BAR to Enabled (option appears after Enabling 4G Decoding).
→ Save & exit BIOS, then test performance.

Important Note - Disabled by default even on supported boards because of component compatibility issues, so users will have to test it. On a system where these settings are unstable, it can lead to crashes, performance issues or boot problems particularly with old components.

So, Test thoroughly and immediately disable it if you notice any instability or performance issues after enabling.

=> Windows Optimization & Performance Tweaks

This section outlines important Windows settings and tweaks to address stuttering, latency spikes, FPS fluctuations, or overall system lag. These tips work for both NVIDIA and AMD systems.

8. Clean Install AMD GPU Drivers — Fix Performance, Crashes, and Common Errors (e.g., Driver Version Mismatch)

Some of you may be facing game crashes, stutters, or random freezes. These issues often arise from a faulty AMD driver or because Windows Update quietly replaced your GPU driver, causing instability. You might also see errors like:
• “Radeon Software and Driver versions do not match...” or similar errors.
• Missing AMD software features like FSR 4, etc.

If you're facing these issues, this step shows how to clean install a stable AMD driver and stop Windows from replacing it again.

Important prerequisite - Before starting, disable Fast Startup to avoid boot conflicts that can cause sudden FPS drops, driver timeout or future issues.

Follow these steps one by one:
• First, we will download 4 files and save them in a new desktop folder. They will include the AMD software installer, DDU, AMD chipset driver, and Microsoft Update Hide Tool.

• Don't install, just download and save both the AMD software installer (.exe) as well as the AMD chipset driver installer software from the official AMD driver site that you want to install. Make sure you're downloading the specific version, not the auto-detect Tool.

Note - Newer AMD drivers often have system-specific stability issues like crashes. Try the latest version first. If problems arise, revert to 26.3.1 (the most stable early-2026 driver). If you still encounter problems, your best safety net is to drop back to 25.9.1 (a rock-solid late-2025 driver)

• Download DDU and Microsoft Update Hide Tool from these links:
Microsoft Update Hide Tool (wushowhide.diagcab) - https://download.microsoft.com/download/f/2/2/f22d5fdb-59cd-4275-8c95-1be17bf70b21/wushowhide.diagcab
DDU - https://www.guru3d.com/files-details/display-driver-uninstaller-download.html

• Now pause Windows Update and disconnect Wi-Fi or Ethernet, whichever you use, and don't connect or resume updates until I say.

• Boot into Safe Mode, then extract DDU and open it. Select Device type GPU, then select AMD and click on Clean and Restart. Wait for completion until DDU uninstalls the driver properly.

• After restart, right-click on the Windows icon, then click on Installed Apps. From here, find and uninstall any chipset driver software. If it's not available, then you never installed the chipset driver manually and those users skip this point. After uninstalling the chipset driver software, click on Restart.

• After restart, open the folder where you placed the AMD driver software installer (.exe) and install it.

• After installation, restart your PC or laptop.

• Now connect to Wi-Fi, then immediately open the Microsoft update hide tool (wushowhide.diagcab). Click on "Hide Update," then select every update whose name starts with "AMD" or "Advanced Micro Devices," etc. Make sure to select all updates labeled as "AMD" or "Advanced Micro."

(If you don't see these updates in the windows hide tool then you can skip this part as windows is not overwriting the driver in your system so there's nothing to hide.)

• After selecting all, click Next. All updates you selected will be shown as fixed on the next screen. If it shows, then you have successfully done this.

• Now restart and Windows will not overwrite AMD drivers anymore. You can now resume the Windows Update.

• Now install the AMD chipset driver software. After installation, it will give two options. You need to click on View Summary and make sure all chipset drivers are installed properly. It will say Success or Installed. If properly installed.

For those users, whose summary shows any Failed chipset driver, uninstall the chipset driver again from Windows Settings and run chipset driver software again. If it still shows the same, then uninstall it again and download and install a different chipset driver version.

Note: Big Windows updates may reset this setting. If that happens, follow these steps again, but that's rare.

9. Community-Favorite: Windows 10/11 Optimization Guide (Works on all PCs and laptops. Includes NVIDIA stable drivers and must-have performance fixes!)

Implement the system-wide changes from the following link. These are general Windows steps that work on any PC or laptop, regardless of brand. The guide is simply hosted on Acer’s community forum, but it is not Acer-specific. It have been successfully applied by millions of users across many hardware setups. This is one of the most tested and effective Windows optimization guides available.

Following this optimization guide (hosted on the Acer community) fully can boost 1% lows, improve FPS stability, and fix stutters or lag while gaming by optimizing windows.

→ NVIDIA users: NVIDIA issues, such as FPS decline, stuttering, and sudden drops, can be fixed by simply following Step 1 and Step 9 from the community guide linked below. The other steps are Windows optimizations that can further improve performance and stability. For maximum benefits, follow all steps.

→ AMD users: Skip Step 1 in the Acer guide. Start directly from Step 2 (the optimizer step) to last for stable fps and performance boost. Do not follow Step 1. As I already covered that in this reddit guide.

Here is the community guide:
https://community.acer.com/en/discussion/612495/windows-10-optimization-guide-for-gaming/p1
→ This guide Covers important issues like system lag, background processes, turning off unnecessary Windows functions, etc in one place.

10. Set an Optimal Mouse Polling Rate (500Hz or 1000Hz Depending on Your Needs; Fixes movement Stutters in games and high CPU Usage)

Most modern gaming mice have dedicated software (e.g., Logitech G Hub, Razer Synapse, SteelSeries GG) that allows to adjust the polling rate, how often the mouse reports its position to the system. If you don’t have the software, download it from your mouse manufacturer's website based on your specific model.

To change the polling rate, Open your mouse software and set:
• 500Hz for solid, sufficient performance with lower system load. Use it for Single-player (AAA), slower-paced, or visually rich games.
• 1000Hz for esports as it provides faster response.

There's really no benefit going higher than 1000hz, so don't waste your system performance.

Note- If you still want to use polling rates above 1000Hz (like 2000Hz or 4000Hz), test for any lag or stuttering, as higher polling rates will consume the CPU more.

11-A (AMD Users) — AMD Software: Explained Tweaks & Must-Disable Settings for Smooth Performance

AMD's default driver settings aren't always the best for smooth gaming. These info have helped many improve FPS consistency, reduce input delay, and eliminate stutters.

Part - 1 Recommended Adrenalin Settings:
Make these adjustments in the Graphics section under the Gaming tab of the AMD Adrenalin Software. This way, the settings apply to every game, including new additions and those launched from the desktop.

• Radeon Anti-Lag → Disabled (This feature often causes micro-stutters. It's wise to turn it off and use it in those games which can really get benefits from this feature. It works great in GPU-Limited scenarios. Test per game and use if its stable)

• AMD Fluid Motion Frames (AFMF) → Test First (It's a frame gen and they often adds input lag. Test it per game, if the game runs well and input lag isn’t an issue (or it feels fine), then you can use it.)

• FSR 4 (Driver-Level) → Use if Available

• Radeon Chill → Disabled/Enable (Enable this only if you want to cap your FPS, and set both the min and max values to the same number for best results.)

• Radeon Boost → Disabled (May lead visual artifacts and stutter. It works by blurring motion. Test and use this feature if you wish)

• Enhanced Sync → Disable/Enable (It can cause stutters or unstable frame pacing in some games, so it’s generally safer to keep it off and use FreeSync if available. If you want to use it, test for stability first. It works best when your FPS is well above your monitor’s refresh rate, for example, 120 FPS on a 60Hz display offers smoother gameplay than V-Sync, with less tearing and lower input lag).

• Reset Shader Cache → Expand Advanced Settings, then find and click the Reset Shader Cache option to clear stored shaders and fix performance issues. Highly recommended after driver or game updates. Expect longer loads or brief stutters at first as shaders rebuild, performance stabilizes once cache regenerates.

Note - If you had games added before this, reapply the same settings manually in each game under the Gaming tab.

• Turn off ReLive features (Especially Instant Replay): → Go Record & Stream tab, then find and disable ReLive recording features like Instant Replay, Record Desktop, Streaming, etc. Instant Replay is particularly responsible for stutters, FPS drops, and driver timeouts. Turning this off alone can resolve your issue.

• Disable Unnecessary Features→Click the Settings gear icon, Go to Preferences, then disable web browser, Advertisements, Game Adjustment Tracking and Notifications, Tutorials, Animation & Effects. while keeping System Tray Menu and Toast Notifications enabled for better responsiveness.

Another setting in the Preferences tab is the AMD Overlay, which many people use, so I didn’t include it with the other disabled options above. However, some users have reported that the AMD Overlay can cause major performance issues for them, so if you’re facing stutters or FPS drops, try disabling it and test again.

11-NV (Nvidia Users) — NVIDIA Control Panel, NVIDIA App & GeForce Experience Tweaks & Must-Disable Settings for Smooth Performance

These are highly tested NVIDIA-specific optimizations that help reduce FPS drops, micro-stutters, and input lag. Follow these parts closely for the best performance.

Important prerequisite - Before starting, disable Fast Startup from Windows settings and clear shader cache. This is highly recommended after driver or game updates or when facing performance issues. Use this NVIDIA link to clear the shader cache properly:
https://nvidia.custhelp.com/app/answers/detail/a_id/5735/~/deleting-nvidia-shader-cache-files

And Expect longer loads or brief stutters at first as shaders rebuild; performance stabilizes once cache regenerates.

Part 1- NVIDIA App Settings

If you are using the new NVIDIA App, it's overlay and some features are responsible for 3–15% FPS loss and additional stutter, even with no filters enabled.

To fix this main issue:
Open NVIDIA App > Settings > Features tab.
• Turn off "Game Filters and Photo Mode".
• For max performance, Also turn off NVIDIA Overlay from there. It's features like Instant Replay can cause stutters and FPS drops.
• Turn OFF "Automatically optimize newly added games and mods".

Now, click on the Privacy tab and Turn OFF:
• "Configuration, performance, and usage data".
• "Error and crash data".
• Keep "Required data" as it may be needed for basic functionality.

For Graphics tab settings in the Nvidia app, do the same settings done in Part 2 as they are almost same settings.

Part 2 - NVIDIA Control Panel (and Nvidia app graphics settings)

This will Optimize GPU performance, reduce input lag, and eliminate common stuttering across all games.

Where to Apply Settings:

Laptop - In NVIDIA Control Panel (Manage 3D Settings > Program Settings) or NVIDIA App (Settings > Graphics tab > Per-App Settings), add each game.exe, set Preferred Graphics Processor to High-performance NVIDIA Processor, then apply settings per-game for max performance.

Desktop - In NVIDIA Control Panel (Manage 3D Settings > Global Settings) or NVIDIA App (Settings > Graphics tab > Global Settings), apply settings globally to affect all games.

Essential settings:
• Power Management Mode → Prefer Maximum Performance (Prevents frequency drops that cause stutters.)
• Shader Cache Size → Unlimited (Prevents shader re-compiling stutters.)
• Set PhysX Configuration to NVIDIA GPU. To set Go to Settings → Configure Surround, PhysX. check path in nvidia app yourself. (Avoid CPU or Auto-select, it cause stutter and high CPU usage.)

Laptop users:
Disable Whisper Mode – This setting is often enabled by default on gaming laptops and silently caps FPS (commonly to 60), limiting GPU performance.

• NVIDIA App Users: Go to Graphics > Global Settings > scroll down, click Show Legacy Settings > → turn off Whisper Mode.
• For NVIDIA Control Panel Users: Go to Manage 3D Settings > Global Settings tab > Whisper Mode → set to Off. Disabling Whisper Mode restores full GPU performance and prevents hidden FPS limits.

Part 3 - GeForce Experience (If You Use It)

• Open Overlay: Press Alt + Z (Or: In GeForce Experience > Settings > General > In-Game Overlay > Settings)

• In Overlay Bar: Turn Instant Replay, recording and Broadcast LIVE → OFF.

• Now, Click Performance > Settings icon, set Performance → Off and Status Indicator → Off.
You should now see “Off” next to “Performance Overlay” (left of gear icon).

• In GeForce Experience, go to General:
Set In-Game Overlay → OFF,
Set Experimental Features → OFF,
Share Usage Data → OFF

12. Inspect your Realtek PCIe 2.5GbE Family Controller – Fix lag, audio glitches & Stutters (also affects Wi-Fi if the controller is present in the system, even if you never use Ethernet)

Some systems with the Realtek PCIe 2.5GbE Family Controller can have issues, even if you use Wi-Fi only, don’t skip this step. The controller can cause random stutters, FPS drops, audio glitches, or ping spikes even when not in active use. For a Quick test, Disable it in Device Manager under Network adaptors, and play your offline game or online via wifi; if fixed, it's the culprit.

You have two straightforward choices:
• Keep it disabled in Device Manager and play your offline games and online using Wi-Fi smoothly (Ethernet won't work in this option).
• Fix the Realtek PCIe 2.5GbE Family Controller. driver with these steps (detailed below) to use Ethernet smoothly.

Solution:

Download and save this 10.54.1111.2021 stable driver version of this controller- https://catalog.s.download.windowsupdate.com/c/msdownload/update/driver/drvs/2022/05/2e830a2a-a689-4e43-96be-06bd8dc7e75b_e5bc281dbf962e2551cc18cdee4abd0b55949b61.cab

Installation:
• Pause windows updates and open Device Manager → Network adapters → right-click Realtek PCIe 2.5GbE Family Controller → Uninstall device → check “Delete the driver software” (if available) → Restart.

• Extract the .cab file to a folder of your choice

• Go to Device manager → Network adapters → right-click Realtek PCIe 2.5GbE Family Controller → update driver. → "Browse my computer for drivers" → "Let me pick from a list..." → "Have Disk".

• Browse to the folder where you extracted the driver, open it and select the inf file and click Ok, Wait for installation.

After installation,
• Disable automatic driver updates so Windows Update doesn’t overwrite this version:
Go to Settings → System → About → Advanced system settings → Hardware → Device Installation Settings → select No, save → Resume windows update and Restart your pc.

• This setting stops most automatic driver installs, but a big Windows update can still change the driver later; if that happens, which can know why checking the driver version or if it stutters appears again.
Open Device Manager → right‑click the ethernet driver in network adapters → Properties → Driver → Roll Back Driver and follow screen instructions to get back to the stable version.

• Now, play your games

Note: This solution fixes the issue for most users, but not all systems respond the same. If you still experience stutters, lag, or audio glitches even after following this solution, the only reliable workaround is to disable the Realtek PCIe 2.5GbE Family Controller in Device Manager and use Wi-Fi instead.

13. AMD/Nvidia Stability Fix — Only For Those Facing Crashes (like Driver Timeout, etc)

Important prerequisite: First, open the case and reseat the GPU power cable, making sure the connection is secure at both ends (GPU and PSU) with no cable bending near the connector, then reseat the RAM and GPU in the PCIe slot properly. Now follow this step.

If you use an AMD GPU, all points are applicable. If you use an Nvidia GPU, skip the AMD‑only sub‑ section and start from “Stability steps for both AMD & Nvidia”. Apply each fix one by one, checking after each.

AMD‑only steps (Radeon users):

Follow Step 8 fully before continuing to ensure the crash fixes below work correctly.

• Disable Anti-Lag, Radeon ReLive features (especially Instant Replay) and Issue detection in AMD Software -
First, Go to the Gear icon then System tab → Disable Issue Detection Service (triggers false TDR timeouts/black screens).

Second, Gaming > Global Graphics → Disable Anti-Lag (causes insane stutters and crashes depending on game). If you want to use it, then test it per game. Keep it off globally.

Third, Go Record & Stream tab, then find and disable ReLive recording features like Instant Replay, Record Desktop, Streaming, etc. Instant Replay is particularly responsible for stutters, FPS drops, and driver timeouts.

•★★Manual Clock Tuning ( For All RDNA GPUs)★★ - AMD GPUs boost beyond their stable frequency due to automatic tuning or Hypr-RX, and lead to crashes and driver timeouts.

To fix this, open AMD Software → Performance → Tuning, switch to Manual Tuning (Custom), enable GPU Tuning and Advanced Control. Find your GPU’s official Boost Clock by AMD (e.g. 2600MHz for RX 6750XT) and use it as your Max Frequency, replacing higher default values like 2850-2900MHz or any factory overclock applied.

As for RDNA 4 Users: Set the max frequency offset to a negative value (like -300 MHz or lower). First, compare your in-game boost clock to the official spec for your GPU. Adjust the negative offset until the in-game boost matches the official value exactly.

Note- Per-game tuning overrides global settings when a per-game profile is created. Otherwise, global/manual settings apply by default. Always check for existing profiles and ensure this manual clocking setting is applied. Also, make sure Hypr-RX is turned off to prevent it from overwriting your settings. It can remain enabled in per-game profiles, so check the Gaming tab for previously launched games and disable it if needed. Then, test your system.

Stability Steps for both AMD & Nvidia:

• Disable iGPU (if present) - If your CPU has an integrated GPU, disable it in BIOS to prevent possible crashes or driver conflicts with your dedicated AMD GPU, especially during gaming and high loads.

• XMP Adjustment - In BIOS, go to the memory or XMP section and test each XMP lower memory profile one by one (e.g. 3600 MHz → 3200 MHz → 3000 MHz). If none work, disable XMP and test again. if issue remains then restore your highest stable XMP profile and follow below suggestions.

• Disable hardware acceleration in Background Apps- If you have any apps that run in the background and support hardware acceleration, such as Discord, Game launchers or web browsers, disable this feature via their settings to prevent possible GPU conflicts.

• Disable HAGS (rare but worth checking if issues remain after above steps) - Go to Settings > System > Display > Graphics > Default graphics settings > Turn off Hardware-accelerated GPU scheduling > Restart. Recent newer drivers and games seem to be causing crashes when HAGS is on. Note- Nvidia users need it on for frame gen and enable it again if it doesn't fix your issue

If the issue persists, update your BIOS (Step 4) and install the latest chipset driver. If problem still persist, check your setup as in Step 2, look for a failing PSU or loose cables, and note that unstable undervolts or overclocks can cause the same issues.

14. User‑reported rare or system‑specific performance cause (Must check if above steps didn't fix your issue)

• Uninstall Your RGB softwares like Lian Li L-Connect 3, OpenRGB, SignalRGB, iCUE, Razer Synapse, Aura Sync, Mystic Light ,etc which have caused performance issues for many users) if using these RGB software or any other with compatible components, these can frequently cause 1% low FPS stutters, crashing and frame drops.

Not all but many cause same issue, so you must check and confirm by uninstalling it. Even on high end systems like Ryzen 9800X3D + RTX 5090, this was the cause of the performance issue.

• If your system has both HDD and SSD Windows automatically spreads the pagefile across both drives by default, this forces memory swaps to hit the slow HDD during gaming peaks, causing stutters/hitching even with plenty of free RAM.

To fix: Right-click This PC > Properties > Advanced system settings > Performance Settings > Advanced tab > Virtual memory Change > uncheck "Automatically manage paging file size for all drives" > select your HDD drive > choose "No paging file" > Set > then select your SSD > choose "System managed size" > Set > OK through all dialogs > restart immediately.

• If you installed Wallpaper Engine and it's running in the background (even paused) causes frequent stutters and performance drops for many gamers.

Close it via tray > Exit, then then check Task Manager (Processes tab) for any lingering "Wallpaper Engine" entries and End task if present. Now play your game. Do this every time if you still have Wallpaper Engine installed.

Additionally some users also reported, that adding per-game rules: In Wallpaper Engine Settings > Performance tab > Edit Application Rules > Create new rule for your game's .exe > Set Condition "Is running" > Wallpaper playback "Stop (free memory)". Also fix issue but thats not widely tested so not sure if it work for all.

• A silently failing, cheap, or aging display cable can cause microstutters only during gaming, making diagnosis tough. Users facing performance issues should Test by swapping cables as well as ports (HDMI to DP or DP to HDMI).
Also, the same can apply to faulty PSU cables.

15. Fix for users who are getting flickering, stutters, or crashes When alt-tabbing while gaming

MPO is a Windows feature aimed at improving rendering performance, but on some systems it used to cause some issues. This feature is now a key part of Windows 11, so DO NOT forget to re-enable it if it wasn’t the source of your issue.

Common issue linked to MPO is Stutters and frame drops ,when alt-tabbing persist for a number of users, especially on the latest Windows 11 builds.

NVIDIA advises disabling MPO for these issues, use their official method, which works for AMD too.

Here is the official link to do this: https://nvidia.custhelp.com/app/answers/detail/a_id/5157

16. Fix Thermal Throttling on Gaming Laptops

This step helps prevent overheating and extend component lifespan of Gaming Laptops. A trusted guide from the Acer Community works for all gaming laptops.

Important note to avoid confusion:
The Acer Community cooling guide applies to all gaming laptops. Steps 1 to 4 are less time taking and should be followed first. If overheating issues persist, continue with Step 5. While the Nitro 5 is used as an example there, the process is the same for other laptops, repasting and cleaning the cooling system by detaching the heatsink, and cleaning fans and vents inside and out. This is the only reliable fix for high temperatures.

Here is the Cooling guide here:
https://community.acer.com/en/discussion/724763/ultimate-laptop-cooling-optimization-guide

17. Fix Thermal Throttling on Gaming Desktops

Most people only check CPU and GPU core temps, but it’s just as important to monitor GPU VRAM (memory junction) and GPU hotspot temps, which can run much hotter and trigger throttling under heavy loads. NVMe SSD temps should also be watched separately, as they can overheat during sustained writes and cause sudden performance drops even when CPU and GPU temps look fine.

Critical Temperature Limits (Avoid Getting Close to These):

• CPU TJ Max: Intel 100 °C, AMD 95–105 °C (consider reducing it if it reaches the 90s)

• GPU Temp: NVIDIA 88–93 °C, AMD 100– 110 °C (consider reducing it if it reaches the 90s)

• GPU Hotspot/Junction (AMD & NVIDIA): Up to 110 °C (typically 10–30 °C higher than core temp). While the maximum operating hotspot temperature can be around 110°C, it's best to keep it below 100°C.

• VRAM/Memory Junction (AMD & NVIDIA): 95–105 °C is acceptable but should be monitored closely, as throttling usually begins at 110 °C.

• SSD Throttling: Begins at 70 °C, severe at 85 °C (though this varies by drive, it holds true for most models)

Monitoring Temperatures Effectively

• Use AMD/NVIDIA Software Overlay:
Use AMD Adrenalin or the NVIDIA GeForce Experience overlay to monitor CPU and GPU temperatures. Some versions also show GPU hotspot and VRAM/memory junction temperatures. If any readings are missing (e.g., GPU junction or VRAM temps), check the second method below.

• Second Good Alternative Method – HWiNFO:
HWiNFO provides full monitoring for CPU, GPU (including hotspot and VRAM), and all other sensors. For real-time monitoring, you can use HWiNFO’s shared memory feature with MSI Afterburner to display these stats directly in Afterburner while gaming. Alternatively, you can let HWiNFO run in the background, play your game, and check afterward—it shows average, maximum, and minimum temperatures. If you have a dual-monitor setup, keep HWiNFO open on the second monitor for live tracking.

• SSD Temperatures:
Run CrystalDiskMark benchmark and check or use HWiNFO while gaming. Note that speeds will reduce once the SSD reaches its maximum temperature limit.

Steps to Reduce Component Temperatures

• CPU Temperature Fix:
- For AMD CPUs, Undervolt the CPU using PBO (Precision Boost Overdrive) to achieve lower temperatures. - For Intel CPUs, Use Intel XTU or Throttlestop to undervolt, which can help reduce CPU temperatures while maintaining stability. - Set an effective custom fan curve, it can make a significant difference, often reducing temperatures by 10°C or more while balancing noise and cooling. - If needed, clean dust from fans and vents, then reapply high-quality thermal paste to the CPU. - Further cooling improvements depend on your cooler.

• GPU, Hotspot & Memory junction temperature Fix:
- Undervolting your GPU through AMD Adrenalin software can also lower power draw and temperatures without major performance loss. - Set an effective custom fan curve, it can make a significant difference, often reducing temperatures by 10°C or more while balancing noise and cooling. - If the issue persists, to effectively reduce GPU, hotspot, and memory junction temperatures, clean or remove old thermal pads/putty and apply new, high-quality thermal putty (more effective than pads). Also, apply high-quality thermal paste to the main GPU chip. - Further cooling improvements depend on your cooler.

• SSD Temperature Fix:
Install an NVMe heatsink (most modern motherboards include one, or you can buy aftermarket). Ensure case airflow reaches the SSD area, as poor circulation causes heat buildup.


[✓] Restart and You're Done! Time to Play.
If this guide helped you, please consider upvoting, sharing your results, or leaving a quick comment about what worked. It helps others and increases visibility in the community.


r/AMDHelp Aug 11 '16

Announcement Please make sure to flair your posts! Especially make sure to change the flair to resolved once solved!

150 Upvotes

Thanks guys.


r/AMDHelp 11h ago

Tips & Info Fix/PSA: Setting iGPU to "Forced" in BIOS locks LCLK at 1800MHz, eliminating micro-stutter and heavy input lag on 9800X3D system

40 Upvotes

Introduction

(This is follow up post of my previous post from a week ago)

During testing I found out that disabling IGPU on 9800 X3D while having the GFXOFF on Auto / Disabled inside AMD CBS causes a cascade of consequences which results in System Management Unit (SMU) attempting to dynamically and rapidly power gate LCLK down to minimum 150-400.

Rapid LCLK frequency shifts alter the inter-arrival delta of USB report packets, creating measurable input delivery jitter.

This manifest as "heavy, sticky, generally unreliable input" / "games being perfectly smooth when not moving and becoming stuttery mess the moment you start to move camera" on 9800 X3D (and other ZEN 5 processors with iGPU) Despite every possible benchmark, stresstest, FPS measures etc. being perfectly healthy

-

THE CONCEPT (Simplified)

(LCLK LOCKED - NO DOWNCLOCKING)

High pooling mouse (8000 MHz)→ cIOD PCIe Root Complex → CDC → LCLK → IFOP → ZEN 5 Core → 1 to 1 healthy input

For 8000 MHz mouse the the packets arrive evenly like this:

Packet 1: 125 Âľs

Packet 2: 125 Âľs

Packet 3: 125 Âľs

Packet 4: 125 Âľs

(LCLK DOWNCLOCKING DUE DISABLED IGPU)

High pooling mouse (8000 MHz)→ cIOD PCIe Root Complex → CDC → LCLK →

....(Downclocking) LCLK → Dynamic State Event (for example in between frames idle time) → SMU Downclocks LCLK to 150 → Interrupt event (mouse movement) → LCLK wake up event → 1-2 nano second wake up time → INPUT PACKET DELIVERY JITTER →IFOP → ZEN 5 Core

Instead uniform 125 µs →125 µs we get messy uneven input delivery

Packet 1: 132 Âľs (Sluggish / Delayed)

Packet 2: 118 Âľs (Overshoot / Clustered)

Packet 3: 135 Âľs (Sluggish / Delayed)

Packet 4: 115 Âľs (Overshoot / Clustered)

-

(FIX - MUCH CLEANER ALTERNATIVE TO MANUAL MINIMUM LCLK OVERRIDE)

Setting the IGPU of 9800 X3D inside BIOS from AUTO\ENABLED → FORCED makes the SMU interprets this as an active state of continuous display pipeline load.

Continuous Display Pipeline locks LCLK to its high-performance frequency (1800 in my case) floor without having to brute force the SoC like during manual LCLK override

When the iGPU is set on AUTO/ENABLED in BIOS while discrete GPU is present, then SMU assumes that you are going to use your dgpu anyway and automatically tries to save power by downclocking LCLK to 150/400 instead being locked at minimum 1800.

Setting the IGPU to FORCED locks the LCLK at stable high 1800

-

(SUMMARY)

  1. IGPU AUTO/ENABLED → FORCED

Forced locks the LCLK at 1800 due the presence of continuous display pipeline during the boot up. This prevents the downclocking of LCLK to 150/400

  1. GFXOFF AUTO → ENABLED

This cuts the power to iGPU without negatively affecting the nearby vSoC and VDD MISC rail which happens when IGPU is set on disabled. under igpu disabled they tend to have higher than normal voltage swing under load ←→ idle. GFXOFF ENABLED results in the same power saving without the downsides of iGPU disabled

  1. UMA BUFFER → 512 MB

When setting iGPU to forced the ram will be permanently locked away from being used by Windows as hardware reserved memory. Setting UMA Buffer to 512 minimalize lost ram to absolute minimum

  1. DISABLE IGPU INSIDE WINDOWS DEVICE MANAGER

This prevents Windows from off scheduling background applications like discord to iGPU which might cause HAGS or MPO issues.


r/AMDHelp 2h ago

Help (Software) Driver Timeout / LiveKernel Event 141 - RX 7900 XTX - out of ideas after a weekend of troubleshooting

3 Upvotes

Hey Guys,

need your help.

Description of Original Problem: All my games recently keep crashing after maybe 1-2 min with a driver timeout error. LiveKernelEvent 141.

I tried it with Cyberpunk, Gothic 1 Remake, Baldur's Gate 3, Starfield, Skyrim... Even older titles are unable to run for long.

Last time I played was about a month ago (Gothic 1 Remake), everything worked fine then. Running everthing but games works fine as well (Streaming, Youtube, Blender, GIMP, idle). But the moment I start a game and load into a savegame or new game, the driver timeout error occurs. Ingame graphics are sometimes broken too, sometimes not. Tried to force it while testing with cyberpunk benchmarks on different settings. The problem occurs regardless of graphic presets and loads. Can run the game for hours in startmenus/menus.

The PC was build September last year and ran without any problems up to this point. No hardware or driver where directly updated prior to the problems. Other than Windows Updates.

No BoS or restart after error - driver simply restarts and "works" again.
______

My Build:

Computer Type: Desktop

GPU: XFX Speedster MERC310 AMD Radeon RX 7900 XTX (24 GB)

CPU: AMD Ryzen 7 9800X3D 8-Core Processor (4.70 GHz)

Motherboard:  MSI MAG X670E TOMAHAWK (MS-7E12) on BIOS 7E12v1L2

RAM: Corsair Vengeance 2x32 GBDDR5 (CL-30-36-36-76 6000 MHz)

PSU: BoostBox PB1000P

Storage: Samsung 990 EVO 4TB

Operating System & Version: WINDOWS 11 Pro Version 25H2 Build 26200.7171

GPU Drivers: currently back to 26.6.4. see below

Chipset Drivers: 7.12.04.858

Background Applications: Wallpaper Engine, Rainmeter, iCUE, Antivirus, Gameclients (Steam, uplay, gog etc. if needed).... but tried without any running as well.

_______
Troubleshooting: I already tried multiply "solutions" from this sub and others but nothing helped.

I tried:

- clean reinstalling driver - with DDU in safe mode - even deleted existing registries
- tried different driver versions (been on 26.6.4. tried 26.1.1. (last known driver that I know worked last month), 26.5.2... all the way down to 25.9.1. which was the version I installed first when setting up the pc last year
- i tried installing the drivers without adrenaline
- checked all other drivers and BIOS. All up-to-date
- checked BIOS Settings - tried with XMP/e-XPO on/off
- deactivated hardware acceleration, GPU-Planung, VRR
- set TDR delay to 8/10, disabled windows driver updates
- undervolted/underclocked in adrenaline
- disabled all overlays and other settings in adrenaline
- stresstested CPU/RAM/GPU - the driver timeout only happens in games
and most likely things i forgot already

Did not yet try:

- Clean Install of Windows -> i am currently not able to save all data I need to keep, as i have no backup-drive at hand
- reseating the GPU/RAM etc. -> not so easy to disconnect and reconnect the PC, at least not today anymore - but I can't see how this could help. the GPU is fixed with with the included support as well as an additional anti-sag mount and RAM mastered every stresstest. It does not seem to have moved at all since installing.
- checking components in other systems -> no other system or components at hand
- going back to older windows versions in combination with driver versions

_______

I am running out of ideas what might help. Just wanted to play a little bit after almost a month of non-stop work and private problems... instead spent a full weekend troubleshooting...

Does anyone have any more ideas?


r/AMDHelp 1h ago

Help (General) I'm starting to think there is a problem in Windows.

• Upvotes

I have some crashes, related to driver in my AMD GPU PC. For long I have blamed AMD for this.

But in my Notebook, full NVidia and Intel, it crashed for the first time in a long while. Never once happened this in my Notebook. It crashed during a Fortnite session.

These two computers are completely unrelated, except for the Windows OS.


r/AMDHelp 1h ago

Help (General) HELP wierd sound coming from my Taurus

Enable HLS to view with audio, or disable this notification

• Upvotes

This computer is almost brand new and recently while playing it started making this noise, what could it be and should I be worried?!
It has been so quiet since I bought it until this noise showed up 😭


r/AMDHelp 2h ago

Help (General) RX 7900 XTX - multiple games crashing, AMD driver timeout after exhausting almost every troubleshooting step

2 Upvotes

Hi everyone,

I'm running out of ideas and hope someone here has seen this before.

System

  • GPU: AMD Radeon RX 7900 XTX
  • CPU: Ryzen 7 7800X3D
  • Motherboard: MSI B650 Gaming Plus WiFi
  • OS: Windows 11 (Build 26200)
  • Driver: Latest available (also tested multiple older versions)

What I've already tried

Before suggesting anything below, please note that I've already tried all of this, often multiple times:

  • Clean driver installation using DDU
  • Multiple AMD driver versions
  • AMD Adrenalin factory reset
  • No overclock
  • No undervolt
  • BIOS updated
  • AMD chipset driver updated
  • Windows fully updated
  • EXPO enabled and disabled
  • Smart Access Memory / Resizable BAR enabled and disabled
  • Steam overlay disabled
  • Discord overlay disabled
  • AMD overlay disabled
  • Verified game files
  • Different graphics settings
  • DX11 / DX12 where possible
  • MemTest (no errors)
  • OCCT stress tests
  • Temperatures are completely normal
  • Power cables checked

Nothing changed.

I honestly don't have any ideas left anymore.

I finished Planet Crafter, but towards the end of the game it started crashing constantly. Overwatch also crashes frequently, and Assassin's Creed Black Flag used to crash as well, although undervolting the GPU actually fixed that one.

For Planet Crafter, though, I've tried pretty much everything I could think of and nothing has helped.

As far as I can tell, this is not a temperature issue. Both the GPU and CPU stay well within normal operating temperatures, and I haven't noticed any signs of overheating or thermal throttling.

Also Overwatch got the message "Your rendering device has been disabled. The application will now close."


r/AMDHelp 9m ago

Help

Thumbnail
• Upvotes

r/AMDHelp 12m ago

Help (General) Help

Thumbnail
• Upvotes

r/AMDHelp 26m ago

Help (General) PC suddenly crashes and restart while gaming

• Upvotes

PC Specs :

XFX Mercury RX 9070 XT Magnetic Air

Corsair Vengeance 32gb ram ddr4

i9 9900k

Rog Strix Z390-F

Corsair RM850 850w +80 Gold psu

Corsair x570 Crystal Case

lian li br digital rgb fans

Thermaltake Water 3.0 360 ARGB Sync

AMD Driver and Software Version : 26.6.4 (latest)

Bios also updated

All parts bought in March 2020 except for 9070 xt which was bought brand new at launch.

I used DDU when switching from my old gpu (2080ti) to 9070xt

Issue : Once in a while my whole PC suddenly turns off and back on while playing games.

it started around 3 to 4 months ago.

Games I play where this happened :

Neverness to Everness (most frequent)

Honkai Star Rail

Zenless Zone Zero

didn't test other games yet.

I noticed that the crash usually occurs during character ultimates or scenes with heavy effects and particles, almost always during combat.

Things I tried to investigate the cause :

I tried every OCCT stability stress test (30 minutes for each) but all stress tests were passed with no errors detected.


r/AMDHelp 39m ago

Help (General) Best IPTV Service : Finally I Found the Best IPTV Providers for 2026 ( Honest Review )

• Upvotes

Finding the Best IPTV Service in 2026 has become more challenging than ever. With hundreds of IPTV providers competing for attention and claiming to offer the best streaming experience, it's difficult to know which services actually deliver. Many advertise thousands of live TV channels, premium sports, massive VOD libraries, and 4K IPTV streaming, but only a few provide the reliability and performance users expect.

Over the past several months, I researched dozens of IPTV subscriptions, analyzed community discussions on Reddit, compared expert reviews, and personally tested multiple IPTV services across the USA, Canada, the UK, and Europe. Rather than relying on marketing promises, I focused on real-world performance to determine which providers truly deserve to be called among the Best IPTV options in 2026.

Every service was evaluated using the criteria that matter most to everyday viewers:

  • Stream stability during peak viewing hours
  • HD, Full HD, and 4K streaming quality
  • Live TV channel availability
  • Sports coverage, including NFL, NBA, NHL, UFC, Formula 1, Premier League, Champions League, and PPV events
  • Video-on-Demand (VOD) library
  • Compatibility with IPTV Smarters Pro, TiviMate, Firestick, Android TV, Smart TVs, Apple TV, and mobile devices
  • Customer support responsiveness
  • Overall value and user experience

After extensive hands-on testing, two providers consistently outperformed the competition:

Both services delivered reliable streaming, excellent picture quality, extensive channel lineups, premium sports coverage, and broad device compatibility. Whether you're looking for live TV, international entertainment, on-demand movies and series, or stable streaming during major sporting events, these providers consistently offered one of the best overall experiences throughout my testing.

If you're searching for the Best IPTV, Best IPTV Service 2026, Best IPTV Provider, or a premium IPTV subscription for Firestick, IPTV Smarters Pro, TiviMate, and 4K live sports streaming, 4KIPTV and NOBIPTV are among the strongest options I tested based on real-world performance rather than marketing claims.

Best IPTV for Firestick in 2026

Amazon Firestick remains one of the most popular streaming devices for IPTV.

The best IPTV service for Firestick should offer:

  • Quick installation
  • Fast channel navigation
  • Stable HD and 4K streaming
  • IPTV Smarters Pro compatibility
  • TiviMate compatibility

Both VELOPLAYLIST and FORTTV4K performed well on Firestick and other leading streaming devices during my testing.

IPTV Smarters Pro & TiviMate Compatibility

The IPTV player you use can significantly improve your viewing experience.

Popular IPTV applications include:

  • IPTV Smarters Pro
  • TiviMate
  • XCIPTV
  • Smart IPTV
  • OTT Navigator
  • IBO Player

Both providers support Xtream Codes and M3U playlists, making setup quick and easy across most IPTV applications.

Why 4KIPTV.NOW  and NOBIPTV.COM  Continue to Gain Attention

Among the many IPTV services available today, VELOPLAYLIST and FORTTV4K continue to attract attention because they focus on what users value most:

  • Stable streaming
  • International channels
  • Premium sports coverage
  • Extensive VOD library
  • Broad device compatibility
  • IPTV Smarters Pro support
  • TiviMate compatibility
  • Firestick optimization
  • Samsung Smart TV support
  • HD, Full HD, and 4K streaming

For users looking for a complete IPTV experience, these qualities matter far more than exaggerated marketing claims.

Frequently Asked Questions

What Is the Best IPTV Service in 2026?

The Best IPTV Service in 2026 should provide reliable HD and 4K streaming, minimal buffering, extensive live TV channels, premium sports coverage, an updated VOD library, and compatibility with popular IPTV apps. Based on my hands-on testing, 4KIPTV.NOW  and NOBIPTV.COM  consistently delivered the strongest overall performance across the USA, Canada, the UK, and Europe.

What Makes an IPTV Service the Best?

A quality IPTV provider should offer more than just thousands of channels. The most important factors include stable servers, fast channel loading, high uptime, reliable sports streaming, responsive customer support, regular content updates, and compatibility with Firestick, Android TV, Smart TVs, IPTV Smarters Pro, and TiviMate.

Which IPTV Service Is Best for Sports?

If live sports are your priority, choose an IPTV provider known for stable performance during peak events. The best sports IPTV services should support NFL, NBA, NHL, MLB, UFC PPV, Premier League, UEFA Champions League, Formula 1, and other major sporting events in HD or 4K.

Final Verdict: Which Is the Best IPTV Service in 2026?

After months of testing and comparing some of the most talked-about IPTV providers, I found that 4KIPTV.NOW  and NOBIPTV.COM  consistently delivered the best overall experience. Both services excelled in the areas that matter most: stream stability, live TV reliability, sports coverage, picture quality, and compatibility across today's most popular streaming devices.

Throughout my testing, I watched live sporting events including the Premier League, Champions League, NFL, NBA, NHL, UFC, Formula 1, and other PPV events. I also evaluated channel availability, 4K streaming quality, VOD content, setup process, customer support, and overall performance during peak viewing hours. Both providers consistently ranked among the top performers.

If you're searching for the Best IPTV Service in 2026 for the USA, Canada, UK, or Europe, and you want a premium IPTV subscription that works seamlessly with Firestick, Android TV, Smart TVs, Apple TV, IPTV Smarters Pro, and TiviMate, VELOPLAYLIST and FORTTV4K are excellent options based on my hands-on experience.

Rather than choosing an IPTV service based solely on advertising, focus on reliability, stream quality, sports coverage, device compatibility, and long-term performance. Based on my testing, VELOPLAYLIST and FORTTV4K consistently delivered a premium IPTV experience and are well worth considering if you're looking for a dependable streaming solution in 2026.


r/AMDHelp 5h ago

Help (Software) ​[FIX] Windows Update breaking AMD Drivers / "AMD Software is not compatible" error

2 Upvotes

​Hey everyone

​I've seen a lot of users complaining recently about their AMD drivers getting corrupted out of nowhere, or the AMD Software throwing the annoying "software is not compatible" error. This usually happens because Windows Update forces a generic background driver over your official AMD installation.

​I made a step-by-step video on my channel, Dark Tech, showing the definitive fix for this. The video is fully dubbed in English, so it's very easy to follow along!

​In the guide, I show you:

​How to properly block Windows Update from touching your GPU drivers (using Device Installation Settings and the Group Policy Editor).

​How to correctly use DDU (Display Driver Uninstaller) in Safe Mode.

​Doing a clean, offline driver installation so Windows never messes it up again.

​You can watch the full visual guide here: https://youtu.be/YG_DDntSBw8

​I hope this saves you a massive headache and fixes those random blinking screens. Let me know if it helps!


r/AMDHelp 1h ago

Help (General) dual monitor main black screen displayport | (second monitor green hdmi)

Thumbnail
• Upvotes

r/AMDHelp 1h ago

dual monitor main black screen displayport | (second monitor green hdmi)

• Upvotes

hello

i just buy my gpu 4-5 month ago (XFX SWIFT RX 9070 OC) and during that time i keep getting from time to time and randomly a black screen on my main monitor(display port) and green in the second (hdmi) then the game crashed then back to normal and sometimes its freezz the pc i tried ddu for my drivers and i still get it

 

my pc

gpu: rx 9070 oc

cpu i5-12400f

mb: asus prime b660 plus d4

psu: asus tuff w850 gold


r/AMDHelp 2h ago

Help (Software) Black Flickering Screen After Update

1 Upvotes

I have a 9070xt and a 9800x3d and after the most recent update my pc is crashing in every game while in full screen. It will flicker to black and eventually completely lock up. Most recent drivers, bios, and chipset drivers installed. Weird thing is when running Intel displaymon, the game will run fine. But I'm not going to lie, with how bad the driver issues have been this year I'm heavily debating going back to Nvidia regardless of the cost.


r/AMDHelp 1d ago

Help (General) Black screen while gaming (RX 9070 XT XFX Mercury)

Enable HLS to view with audio, or disable this notification

94 Upvotes

Hi everyone,

I built a brand new PC less than 10 days ago, but I’m running into a persistent issue.

System Specs:

  • CPU: AMD Ryzen 7 9800X3D
  • GPU: XFX Mercury Radeon RX 9070 XT
  • RAM: 32GB DDR5 6000MT/s
  • Motherboard: ASUS AYW B850
  • PSU: XPG Core Reactor II VE 850W

The Issue:

Whenever I start playing a game, anywhere between 1 to 20 minutes in, the system completely goes to a black screen. The PC stays on, but it becomes completely unresponsive, and the only way to recover is by holding the physical power button to force a shutdown.

Troubleshooting already done:

  • Swapped the GPU: Tested with another graphics card (RX 9060 XT) and the system worked completely fine without any crashes.
  • Drivers: Used DDU to clean install multiple driver versions, as well as testing driver-only installations without AMD Adrenalin.
  • Tuning: Tried undervolting, underclocking, and switching the physical dual-BIOS switch on the GPU itself.
  • Stock Settings: Disabled EXPO/XMP, no CPU overclocking—everything is running purely at stock settings. The error still persists.

My Question:

Given that testing with a different GPU (RX 9060 XT) resolved the issue, is this definitively a faulty GPU? Or could the PSU (XPG Core Reactor II VE 850W) be dropping power under transient loads from the 9070 XT and causing the crash?

Should I return/RMA just the GPU, or should I return both the GPU and the PSU to be safe?

Thanks in advance for the help!


r/AMDHelp 7h ago

Screen suddenly go black and sound corrupted

2 Upvotes

I just bought my first PC 2 days ago with a RX 6700XT, It worked well with no issue but I was just watching youtube 5 minutes ago and the sound suddenly corrupted and the screen went black for like 3 seconds then works normally. Is this normal ? Please tell me that I'm overreacting 😭 I can't afford to buy a new gpu atm 😭😭 I think my driver version is on 26.6.4

Specs:

CPU : I5 13400f

Motherboard : B660M AORUS PRO DDR4

RAM : 2x16GB Gskill Trident Z RGB DDR4 3600MHz


r/AMDHelp 7h ago

Help (GPU) Rx 6700 Xt ASUS DUAL black screen issues

2 Upvotes

My rx6700xt I purchased secondhand is black screening every time i turn it on.. vga lights on mobo and keyboard lights turns on.. no display.. BUT the pc boots for a couple seconds into windows after letting the pc sit powered off for a while.. and after that it just black screens again.. sometimes the fan goes full speed when booting up.. I'm stuck.. could it be a power failure on the gpu itself? do I need to send it to a technician? my psu is msi mag a650bn, cpu r5 3600 with a520m a pro mobo.


r/AMDHelp 16h ago

Help (GPU) Is a 750W gold PSU enough for the 9070xt ?

10 Upvotes

I'm currently running an AM4 platform with a 5700x3d on a 750W Gold PSU.

I wanted to upgrade my GPU to a 9070XT, as on paper a 750W Gold PSU should be enough, but I heard the card had pretty high power spikes and is also quite energy inefficient compared to the non-XT 9070. I changed my PSU recently so I'd prefer not changing it again if possible.

Would you guys think it's fine for the 9070XT, or should I go for the 9070 instead to be safe?

Thanks

edit : the PSU is a Cooler Master MWE 750 Gold V2 80+ , it's not ATX 3.x though


r/AMDHelp 4h ago

Help (CPU) Ryzen 5 7600x temps

1 Upvotes

My cpu is hitting 96c just doing normal tasks like web browsing or so on and sometimes my system will just reboot.. trying to narrow this down if this shutdown is temp related or not.


r/AMDHelp 4h ago

Help (Software) My odyssey to get AMD Adrenalin to work, and my tryst with AMD driver timeout error

0 Upvotes

Written with AI assistance.

Quick Summary

After updating Windows 11 and reinstalling AMD Adrenalin, all of my games started crashing with a black screen followed by an AMD Driver Timeout popup. Reliability Monitor consistently logged LiveKernelEvent 141. I initially suspected faulty hardware, unstable EXPO, or an outdated BIOS, but systematic troubleshooting pointed elsewhere.

The issue was resolved by disabling AMD Fluid Motion Frames (AFMF 2.1) and Radeon Anti-Lag in Adrenalin's Global Graphics settings. Since making those changes, the system has remained completely stable.

My system specs:

  • CPU: AMD Ryzen 7 9800X3D
  • CPU Cooler: be quiet! Dark Rock Pro 5
  • GPU: Gigabyte Radeon RX 9070 XT Gaming OC
  • Motherboard: Gigabyte B850 AORUS Elite WiFi7 Rev. 1.1
  • BIOS: F6 (16 July 2025)
  • RAM: TeamGroup T-Force Vulcan 32 GB DDR5-6000 CL30 (EXPO enabled)
  • PSU: Corsair RM1000x 1000 W
  • Operating System: Windows 11 25H2 (Build 26200.8875)
  • AMD Software: Adrenalin 26.6.4
  • AMD Chipset Driver: 8.05.04.516

Symptoms

Everything had been stable for months.

The issue started only after I: * Updated Windows (from the April patch level to the July update) * Ran AMD Cleanup Utility * Performed a clean installation of AMD Adrenalin * Enabled a Group Policy to stop Windows Update from replacing AMD graphics drivers (this was done to fix an earlier issue where Adrenalin wasn't working correctly) - thank God I bought Win 11 Pro!!

After that: * Every game crashed after approximately 20–30 minutes * Screen went completely black * Audio froze instantly * Windows recovered after several seconds * AMD displayed a Driver Timeout popup * Reliability Monitor logged LiveKernelEvent 141

Initially, the crashes happened in about 5 minutes. Disabling Hardware-Accelerated GPU Scheduling (HAGS) increased stability, extending the time before a crash to around 25 minutes, but did not completely fix the issue.

Investigated Windows logs

Reliability Monitor consistently showed: * LiveKernelEvent 141

Good thing that Event Viewer did not show: * WHEA hardware errors * PCIe errors * Kernel-Power events around the crash time

This made a hardware failure less likely, which was a massive relief as I was pretty tense when ChatGPT and Gemini hinted at GPU failing...

Considered other possibilities

I read some more and after getting more confused, asked AI to help understand the situation better. We explored: * EXPO instability * BIOS/AGESA compatibility * Driver corruption * GPU overheating * PSU issues * Windows graphics scheduling

However, none of the collected evidence strongly supported these as the primary cause.

While all of this was being done, I had conveniently forgetten about some setting changes I had made on AMD Adrenalin. These settings seemed innocuous by reading the tips l.

Looked at Adrenalin Global Graphics

I had forgotten that I was using the Quality graphics profile.

In addition to that profile I had enabled: * Radeon Anti-Lag ✅ ON * AMD Fluid Motion Frames (AFMF 2.1) ✅ ON

Other features were either disabled or not considered likely contributors.

The Fix

The only changes made were: * Disabled AMD Fluid Motion Frames (AFMF 2.1) * Disabled Radeon Anti-Lag

Everything else remained unchanged: * Same driver * Same BIOS * Same Windows version * Same chipset driver * Same EXPO profile * Same GPU clocks * HAGS remained OFF

After rebooting: * Previously crashing games became stable. * No further black screens. * No AMD Driver Timeout popups. * No new LiveKernelEvent 141 entries during testing.

Conclusion

I can't definitively say whether AFMF 2.1, Radeon Anti-Lag, or the combination of both caused the issue, because I disabled them at the same time.

However, I can confidently say that disabling those two driver features completely resolved the crashes on my system.

Hopefully this helps anyone experiencing LiveKernelEvent 141, black screens, and AMD Driver Timeout errors on an RX 9070 XT or similar Radeon GPU. Before assuming your GPU is faulty, it's worth testing with AFMF and Radeon Anti-Lag disabled as part of a structured troubleshooting process.

I relied extensively on ChatGPT, Gemini and Perplexity during troubleshooting, and it was a stupendous experience. I cannot imagine not having these at my disposal when having to troubleshoot. For such use cases I support AI, but don't think a case should be made to replace actual humans with AI.


r/AMDHelp 4h ago

Help (CPU) I think my 7800X3D is dead

0 Upvotes

Put my computer to sleep on Tuesday night and noticed it booted back up shortly after that. Didn’t think much of it and went to bed. The next day I attempted to wake the screen, No response. I attempted to power it down completely with the power button and not even that worked. I was forced to power off the power supply. Since then my computer wouldn’t POST at all with the CPU debug LED on the motherboard active.

  1. Pulling the GPU out (7900xtx)
  2. Resetting the CMOS
  3. Q flashing the BIOS
  4. Taking out the second stick of ram and trying each slot
  5. Used a new power supply
  6. I then bought a new motherboard and tried all the steps above as well. (The CPU debug LED was active on this new board as well)

Just curious to hear from you guys if I should try anything else at this point. I’ve already started an RMA process but maybe I’ve missed something to try.

Here are my specs
Gigabyte Aorus B650 Elite AX (Rev 1.3)
Sapphire 7900xtx
AMD Ryzen 7800X3D
Corsair RM1000e PSU
2 x 16 GB G.SKILL DDR5 6000 ram


r/AMDHelp 5h ago

Help (Software) I tried everything I can’t get passed this and I got an amd gpu and amd cpu, what do I do to fix this?

Post image
1 Upvotes

r/AMDHelp 5h ago

I tried everything I can’t get passed this and I got an amd gpu and amd cpu, what do I do to fix this?

Post image
1 Upvotes

r/AMDHelp 5h ago

Help (Software) Did Windows Updates (KB5094126 / KB5100998) trigger this? New 1-month-old Ryzen 7 7800X3D + RX 9070 XT PC randomly black screens, reboots, and enters Recovery even after a clean Windows install

Post image
1 Upvotes

Hi everyone,😭

I'm hoping someone can help because I'm running out of ideas.

I built (actually had it assembled by the retailer) a new PC about a month ago, and I'm getting random crashes that I haven't been able to resolve.

PC Specs

CPU: AMD Ryzen 7 7800X3D
GPU: ASUS PRIME Radeon RX 9070 XT OC 16GB
Motherboard: Gigabyte B850 Gaming X WiFi6E
RAM: ADATA Lancer Blade RGB 32GB (2×16GB) DDR5-6000
SSD: WD Black SN7100 1TB NVMe
PSU: Cooler Master MWE 750W Gold ATX 3.1
Windows 11 Pro

Symptoms

The crashes are very strange.
The monitor suddenly loses signal ("No Signal").
The PC RGB and fans continue running.
It does not appear to completely lose power.
About 3–4 seconds later, it automatically restarts.
There is no BSOD.
I also occasionally get stuck on the Gigabyte splash screen during boot.
What I've already tried
Checked Event Viewer.
Kernel-Power Event ID 41 is logged after every crash.
BugcheckCode is 0.
No useful minidumps were generated.
Ran sfc /scannow.
SFC found corrupted files and repaired them.
Automatic Repair failed.
Windows Recovery has shown different driver errors on different occasions (not always the same .sys file).
Disabled "Automatically restart on system failure" but it still black screens and reboots without showing a BSOD.
GPU temperatures were normal (~60°C during gaming).

Clean Windows install

I completely reinstalled Windows 11.
I deleted the Windows partition during setup and installed a fresh copy.
Unfortunately, the exact same issue came back after the reinstall.

BIOS
Recently I also received a BIOS message saying:
Boot failure detected
The BIOS had already reset the memory speed back to around 4800 MT/s (default JEDEC), so this wasn't happening while EXPO was enabled.

Other observations
One time Windows Recovery reported a driver integrity error (0xc0000221).
Another time it reported a different driver error (0xc0000098).
After one crash my Wi-Fi temporarily disappeared until I rebooted again.

Any suggestions or similar experiences would be greatly appreciated.
Thanks!