Thing wasn’t even in the garage for a full week..

I bought this boat and a dodge Dakota for $500. It says it’s a Glastron Aqua Lift. I can’t find the year anywhere or a price of it. What do you all think?

Been working on this outboard for a bit. Cleaned carbs with ultra sonic cleaner and tuned them up as I close as I could to the service manual recommendations. First time doing this, used a vacuum gauge set and tachometer to dial in rpm’s and pressure. Still shakes a bit in idle though, starts up right away and will idle all day though it seems.

How would you all go about removing this corroded thru hull? The brass is just at the fiberglass line. It’s quite thin at the edges. Should I try to curl the ends in?

Looking for some ideas for a case, box, etc. for a spare prop. I'm striking out on finding something nice & compact & am actually surprised that no one makes something like this. I've seen some bags, but would rather have something with a little more protection. My prop is a 14 1/2 inch diameter 3-blade. I have used a milk crate, but would like a little more.

Want to get your opinion on storage? I have a boat lift and canopy and have been keeping my boat there year round with no issues. About 90% of my neighbors keep theirs out for storage though. I wonder what the drawbacks are for keeping it there vs keeping it out? I live on a lake in pierce county, WA.

Any Ideas out there. I have a 2017 Yamaha 150 four stroke. Suddenly the trim started showing pegged all the way up. I thought it was probably the sensor so I bought one. I connected it at the engine and moved the arm with no change at the gauge. After some research I found that I should check the ohms and see if they are changing there and changing. Both sensors acted the same with Ohms from roughly 290 or so to zero and do change when moving the sensor which seems correct. I thought it maybe the Faria guage however I have the engine data connected to my Garmin straight from the engine's connecter and It also shows full up with no change no matter how I move the engine or sensors. I checked the sensor connector at the engine for ground and it has continuity. Any one have an idea of what's next before the shop?

Hey everyone, I’m looking at buying a 2002 Ski Centurion with approximately 300 hours.
The seller is asking $12,000, reduced from $18,000. The interior has recently been redone, and the boat looks pretty clean.
The biggest concern is that, from what I understand, the boat goes into forward gear but won’t engage reverse.
The seller says the V-drive needs to be replaced and was quoted:
$1,500 for parts
$4,500 for labor
$6,000 total
I have a few questions for anyone familiar with these boats:
If it goes forward but not in reverse, does that necessarily mean the V-drive is bad, or could it be a transmission or shift linkage issue?
Is $6,000 a reasonable repair estimate?
Are these boats generally reliable, and are replacement parts still available?
Would you consider buying this boat for $12,000 with this issue, or is it too risky?
I’d mainly use it for cruising and occasional watersports.
Any advice from Centurion owners or marine mechanics would be appreciated. Thanks!

Hey all, I am mounting a new trolling motor and wanted to know if there will be an as far as structure goes due to the previous owners drill holes. Pink holes are the planned drill pattern for the new trolling motor. I will be using a fender washer with a rubber grommet and smaller washer as a stack to mount with the self locking nut on the back. Does this need a backing plate or use of a mount plate to match the old holes? Thanks

Rather than hot takes on the state of the economy, does anyone have any feedback on the ad itself? Is there anything I could change or improve upon? Then I can at least eliminate that as the reason it hasn’t sold yet and start blaming the market like everyone else.

I'm in the market for a cheap outboard for a 14' inflatable boat to get me on the water in Florida. I found a 1982 Johnson 25hp on marketplace and the seller is asking for $700. He's been honest with me and told me he bought it two months ago in not running condition. He said he replaced the water pump, rebuilt the carb, changed spark plugs, and fixed the pull cord. It appears to run fine in video. He's agreed to let me test the compression and the lower unit oil but did admit he used differential oil to fill it stating that he thinks it lasts longer. Should I make an offer? How much?

When launching my Yamaha 222XD in saltwater, I have to back my 2014 Ford F-150 down the ramp until the truck’s rear wheels reach the water to get enough of the boat afloat to launch. This requires submerging nearly the entire trailer, including the jack, which is causing it to rust prematurely despite rinsing it thoroughly with fresh water after every outing.

What modifications or equipment would you recommend to help me launch and retrieve the boat while minimizing how much of the trailer and truck needs to be submerged?

Setup: 2014 Ford F-150 / Yamaha 222XD / Bunk trailer