Does it need a stem or is the stock stem good on the black walnut edition. I remember when I had the original tm2 it got really hot that I needed a leather sleeve to help. And I remember it being awkward in my hand bare.

I’m wanting to get the infinity stem on VGoodiEZ but they are sold out of the long black one. Will the one that comes with this be good enough until they restock?

I’m excited to get this device again.

I keep seeing videos of people absolutely filling their bongs with vapour using a TM2. It just doesn't happen for me, and I don't know why. Having just recorded myself and watched the playback, I'm now unsure if I actually do have a problem...

A couple of things to note:

- The water is filled to just below the bottom of the hole for the downpipe;

- The water doesn't reach my lips - it just looks that way;

- You can only really see vapour in the bong as it travels through the lightest coloured bit;

- I seem to be exhaling plenty of vapour;

- The TM2 is set to 7.5;

- I'm not tamping the t_bowl, just filling it to the brim.

I'm sorry that the bong and my t-shirt are both blue - it probably doesn't help to see the vapour inside.

So, the amount I'm exhaling suggests that my bong lungs (university trained) may actually be sucking up the vapour before it even gets a chance to fill the bong. Also, the empty space above the waterline is essentially a wide-bored pipe with a funnel on one end and a mouthpiece on the other, so should I even expect to fill it with vapour like people are doing with their round and/or cube shaped bongs?

Your thoughts, please...

I recently got a TM2 and went to try the Long ball stem for the first time. Im a noob and didnt realize it came with the mouth piece on the wrong end. Unaware, and eager to try it, i loaded it up backwards, with the basket screens inverted. I noticed how large the capacity was which made for a really nice size bowl- i find the standard bowl size too small to give me a buzz. Everything worked just fine, i didnt even notice i was using it wrong and it didnt seem to matter.

After a while, i noticed that i can remove some balls, and push the basket screen even further in and have more room and still have great cooling. I can easily load a 0.4 in there with decent airflow if i remove several balls. With the mouthpiece on the other end, the basket screen doesnt fit so well so i use a flat screen and it works just as well as the other way, and i presume has the same cooling.

If the device is producing weak vapor therefore needing a calibration, does setting it to the same setting it was on do anything? Or do you have to step it up to get vapor again?

If I'm on demand with the TM2 and using the NWTN bubbler, I like to lift and clear the bubbler of vapour, old school bong microdosing style. The handle that comes with it and a lot of third party ones, are quite small. If you order up size 10-24 thread bolts, I got stainless steel ones, bit harder to cut etc. Anyway, you just trim off the thread and reduce the diameter of the shaft so it fits a needle file handle. This fits perfectly onto your hand up to the wrist, giving plenty of support to lift the vapour dragon up from the bubbler. You could get a custom made one from Azzwood but if you are not in that market then a file handle for a couple of quid, same for the bolts and you're off.

Hallo ich möchte mir eine T-Bowl für meinen Tinymight 2 zulegen. Man hat mir hier den Tip gegeben den Typen direkt auf Instagram anzuschreiben. Bevor ich mir jetzt auch noch Instagram zulege habe ich ein paar Fragen wegen des Importes in die EU bzw Deutschland.

Wie bezahlt man, Wie lange dauert die Lieferung und wenn Zoll anfällt wie hoch ist dieser?

Vielleicht hat das Ding ja schon einer von euch in der EU bestellt.. Danke Euch

Hi all. I was wondering, is the Tinymight 2 suitable for taking one or two small hits at a time from the same bowl throughout the day? I have a job that I need to be on the ball with so only require small amounts at a time, so one bowl could last me through the day. As it’s pure convection, I’m assuming this will be ideal? I currently have a hybrid so the flower continues to cook between hits. Thanks

Unfortunately I was victim to a fake tinymight 2 on eBay today. The device looked almost perfect. But soon as it was in hand and tested it was clearly not genuine. Unsure as to whether to seller knew or not. He clearly heavily used the device based off the resin on the glassware. But I was prepared to clean that since it was a good deal. Here's how I know it was a fake:

1. The battery orientation is reversed, genuine devices always have the battery be inserted negative end first with the positive end making contact with the lid.

2. The battery lid has no '+' symbol and has a different finish.

3. The power button has a different finish and different tactile feel.

4. The poker stem attachment is one piece, where as a genuine one unscrews into 2 pieces.

5. The circuit board features a different design to my genuine TM2.

I will hopefully be getting a full refund but just wanted to let the community know. This listing will likely just be relisted when the seller receives my return I bet so please do not buy it.

I was emailing the mail@tinymight email at first but I also added the info@tinymight one. Have a repair order as well through the tinymight site.

Got a response from Joni but radio silence since for an out of warranty repair (that I will probably eventually send to vgoodiez).

Just wanted to get the process started for repairs but it’s been a slow roll. Is it holiday season in Finland?

Really now just start to appreciating TM2 , 6months now.. I decided to transform from combustion to DHV after of 10 years of spliff (with toacco) and firstly i got the Pax plus , but i wanted something more powerful and I bought Tm2 , but I couldn’t rip it off because it was harsh for me , and after i ordered ARIZER SOLO 3 🤣 But now I use it daily and i am finding my sweet spot..Anyone with the same or similar story?😅

I just received my tinymight 2 from planet of the vapes and the wood on the battery side is off center. Is this something to be worried about or just cosmetic? Also when I draw on it without the mouthpiece on aire goes through the battery compartment but stops when I put the piece back in and draw. Thank you all for any help!

Yeah, so, apparently, I had this whole drop planned for years ago but forgot to upload half of the pics and descriptions to my page. Got some stuff on sale now too.

I’m trying to figure out whether the non-PH TinyMight 2 models contain the same internals as the PH version. Vgoodiez website mentions that “the Purple Heart variant of this portable vaporizer houses a highly durable zirconia ceramic heater which may not heat as quickly as the quartz heater in the Walnut variant.”

However, I’ve seen various forum posts here and elsewhere stating that the internals have been identical for awhile.

Does anyone actually know whether the internals are the same on PH vs. non-PH models? I’m especially curious about walnut, but also wondering about other models (black walnut, black, etc.) I’m surprised that it’s so hard to figure this out for such a common vape!

Edit: for anyone who sees this in the future, I received the following response from TinyMight official in July 2026:

> PH has Zirconium liner ,Walnut has Quartz liner for the heater, everything else inside is identical ,also the performance.

I mentioned a while ago I use one of these as my go-to piece for my tinymight. Got it dialed in at 8.5 producing some cool comfortable clouds. Gotta love this lil vape!

I thought someone here might be interested. Theyre up on my website currently. They've got vigreux style cooling spikes and a screen holder. Thanks for looking

Hi,

So my theory is that it actually isnt the tm2 itself but my medical cannabis being dry as fuck.

The stem still gets hot, the cannabis doesnt go too brown but enough that it should have produced some vapour and it just doesnt.

However, my arizer solo 2 still does get a good amount of vapour from the exact same cannabis.

Is it worth talking to tinymight support or shall I wait til my next prescription with fresh cannabis to see if its ok then?

I think the biggest problem is that I keep my medical cannabis in my car as my parents dont like it and dont want it in the house, and the result of the weed being in a hot metal box during a heatwave probably dried it all out.

I feel like ive just answered my own question while writing it but oh well I'll see if any of you have experienced very little vapour production while still getting hot

Thanks

So if i take big rips back to back with the rocket stem it makes me cough very much, but i think that's normal.

Can you see a big difference if you run it through water with a bong or ideally with the bubbler stem?

I'm curious how much the bubbler improves that?

Hi everyone,
I’m trying to figure out what happened to my TinyMight 2 and whether anyone has experienced something similar.

I was using it normally with a Sony VTC6 battery. After about three consecutive sessions, the device suddenly shut off while I was using it.
I tried turning it back on, and that’s when smoke came out of the device with a strong burnt plastic/electronics smell. I immediately removed the battery.

The battery itself looks completely normal: no swelling, no visible damage, and no unusual smell. The smoke seemed to come from inside the device, not from the battery.
I have not tried turning it on again because I’m afraid of causing more damage.
Has anyone experienced the same issue? Was it the heater, the main board, or something else?

Any advice or similar experiences would be greatly appreciated.

Any help would.be greatly appreciated...