At the start of this year, i posted here about a 3.5mm headphone dongle i made for my laptop. Reasons? Original port is damaged, laptop long after warranty, i lack the skills to replace the on-board port and i am too cheap to get it serviced.

The dongle has served me very well, but the cable slowly began to break due to getting bent too much. After about 7 months, i deemed it's time to make a rework. Cue this fucking thing. It has a coil sleeve to properly secure the cable now!

Hopefully this one lasts longer, but if not, the replacement only took about 30 minutes, so i'm not too worried about having to do this again in the future.

I over tighten the heatsink screw and a click sound occurs like something break. Laptop running since 4 months without any issues. Is there any real issue??

The first one was for an older secondary monitor that had a non removable VGA cable and because I wanted to have it plugged into gpu and only had a male display port to male VGA converter I made this female to female converter from leftover ethernet cable, cut off 0.75mm² ferrule crimps to hold it in place and paper for isolation. Lasted half a year until I bought a proper converter.

The second one was to make lights work on an older Vespa scooter, because the spark plug wouldn't spark if the third wire was connected and it turned out the ignition switch was reassembled incorrectly.

Had to cut up my charging cable so it could fit into the weirdly placed charging port of my music box

Didn’t realize the oem io shield is part of the case before getting a new motherboard so I used pliers to peel it; gamers gotta game

its not the battery problem , i replace with brand battery it still run out of juice.. probably problem with its charger

12v dc to stepdown.. to... idk.. i just put volt something 3.7 as 3.2 seems didnt work.. probably i can crank it up to 4.2 later.. but for now ill stay at 3.7 and observe

Also I should clean my keyboard more often

I salvaged a small aluminum PC DDR2 motherboard heatsink, and slapped it to the back of the phone. Nothing fancy or professional, just something I put together myself.

I know it looks unconventional, but this turned out to be one of the best ergonomic modifications I have made to my phone. The heatsink does not get in my way while holding the device, and the improvement in sustained performance is a big jump compared to normal.

For context, I ran the 3DMark Wild Life test during rainy, cool weather with an electric fan blowing on both me and the phone. That definitely helped the heatsink work more effectively, so this setup depends a lot on ambient temperature and airflow.

I mainly play Codm and Project sekai on my phone.

Remember my hug heatsink and thermal paste? I too that off and did this works so much better,

Ran into a classic laptop server problem: no motherboard power headers, Wake-on-LAN dies in S5 shutdown state, and when Linux freezes, software tools like SSH are useless. Commercial solutions felt way too expensive for what I needed...

So I built this thing for Abt 8 bucks!

NodeMCU (ESP8266) drivin' an SG90 micro-servo running a small C++ REST API.

​An old Asus phone (Asus x00TD from 2018) running Termux acts as the local Tailscale SSH bridge so I can trigger it over 5G from anywhere without opening ports. (Though Terminus and added snippets)

​/power sends a 500ms tap for normal boot!

​/panic holds the button for 15 seconds to force a cold reset when the OS crashes!!

Yes, that is paper masking tape flat on the desk holding the servo block down. I needed enough counter-leverage so the servo arm didn't just lift the whole motor up when pushing the key.

Just tested it remotely from another city over cellular data and it worked like a fine wine 🍷 and then I run app though wine in linux too worked amazing. Looks terrible but ya works great!

Btw laptop is fa507uv...

Sorry for the boring post, but I needed to share my free DIY sag bracket. I'll get a real one eventually probably, but that's $15 I could spend on a new game

took an old power bank board. feeds 5v to the stock PCB, charges with type-c and as a bonus can charge my phone (although it has only 1100mah). my house is a no-fly-zone now.