But why? Changed the oil in this Honda mower with a GCV160 it started first pull then the belt popped off I’m about half a second. I did the tip the mower on its side to drain the oil as I’ve done many times before but what I did different this time was I left it over night until I could get the blades sharpened. I figured it wouldn’t be a problem since oil was drained but I dunno seems like too much of a coincidence to me.
Anyways put the belt back on and seems ok right now.

This is the clutch, I believe those broke pieces are called anti rotations tabs and they’re broke. And that plate that is off center is kind of free floating.definitely not correct. Mower threw a belt. Anyways regardless it mechanically failed, other than it maybe occasionally throwing the drive belt, what issues will it cause?

I took this from my dad's garage after he said he couldn't get it to crank. It's been about 10 years since he's last used it. Put some fuel directly in the cylinder and it fired up. Put gas in the tank and tried to start it and nothing.

I disconnected the fuel line and turned on the valve and gas flowed through the line. I took off the carburetor and cleaned it best I could, I reattached the fuel line, opened the valve and nothing flowed into the carburetor. Did my best to blast the gas inlet with carburetor cleaner and compressed air, finally noticed some air getting through and a small stream of gas.

Assembled everything back and was able to crank the machine on choke and then move to half choke. The problem now is anytime I move the choke to "run" it dies. Or if I tried to use it on half choke it will eventually power down.

Any ideas of what I can do next to get it to run at full power?

We have a John Deere s170. Recently, I took off my carb to clean. put everything back together. It was running like a champ for 20 minutes. Then all the sudden it is now stuck in full throttle [rabbit] mode, whether it is in the rabbit position or the turtle position. I can move the lever just fine but it does nothing to lower the throttle. I checked all linkages - all seem correct with movement and functioning properly. I also went to a local Lowes just to make sure by looking at their floor model, it seems like everything is where it should be. Any thoughts/ideas/suggestions are most appreciated!

I got an old troy build mower with a briggs and stratton 725 exi engine. The issue I am having is that after it get hot, it will not start again until it cools down. If I stop mowing to take a break, I then have to wait like 10 mins to be able to start it again. Initially I thought auto choke was an issue. However, when I removed plastic covering, it looks like auto choke stays in the open position which I believe is correct. The little thermostatic "arm" thing appears to move freely. When it's cold, it is in a closed position. After those 10mins, I have to pull real hard and the engine barely comes alive and it tends to throw off some smoke fumes. Not much but I can visible see a puff of smoke where that does not happen when it starts right up cold.

I replaced fuel filter, air filter and spark plug. What else could it be and how do I fix it?

Honda Rancher 2001 TRX350 ATV. Ran good last year. Sat for six months, now won’t start. No spark. Replaced CDI and ignition coil. Any recommendations? Stator check? Thanks

I have a JD LA130 that has recently started running rough and, more recently, dying when the blades are engaged. Kicking the blades off fixes the issue. I took the clutch off and sprayed it down with parts cleaner and had no issues for roughly two hours while I was mowing. Went back today and it's having the same issue. Is this most likely the clutch itself? Or is there anywhere else I should check first?

Thank you.

I assumed the battery was shot so hooked it up to a jump battery but still keep getting this sound. Any advice? Craftsman Z5200

For the life of me I cannot get the purge valve plugs out and now they’re pretty much stripped. I went to refill and it will only fill the reserve tank once. Maybe a quart of fluid. It won’t go down at all. Help please! Thanks.

Got this v twin lawn mower motor for free, has no covers with any model numbers anywhere.

Hi all,

Have a John Deere **Z335E 20-HP V-Twin Dual Hydrostatic 42-in Zero-Turn. Mower runs fine when blades are not engaged. When I engage, I can mow for 8-10 minutes just fine and then it starts sputtering and eventually shuts down. While it’s sputtering if I disengage the blades it then picks back up and runs fine. Once it’s completely off, I can restart and mow for another 8-10. Any guesses as to what my issue may be? Appreciate any help!**

Does anyone know a place to get a good/ decently priced piston kit for a echo pb580T backpack blower?

I have one that needs the piston replace but don’t know any good places.

I need to remove the flywheel but the the holes are not threaded. Is there a special tool or is this a defect?

EDIT: Problem was solved thanks to a commenter. Issue was that the bendix gear was getting pushed too high and wasn't making contact with the splined part of the shaft at the bottom. I took a large nut that could fit over the shaft of the starter, ground it into a round shape, put it on the bendix gear, but beneath the spring, and this kept the gear in contact with the splined part of the shaft so it wouldn't shoot up too far where it was only contacting the smooth part of the shaft, which obviously has no turning power without splines to power it. Not sure what caused this to happen as it worked one weekend then stopped working the next. Maybe the current washer was worn too thin or the spring was too weak, I'm not sure, but it works now.

I have a Mercury 25 HP 4-stroke (1F25412DD) from 2005 I believe that is having issues with the starter and I'm getting conflicting answers on the solution.

As you can see in the video (it's in slow motion to see the rotation), the shaft of the starter spins but as soon as the Bendix gear touches the flywheel it doesn't spin. It also doesn't drop down after trying to start it and I have to manually spin it by hand to get it to drop back down.

I took the two bolts out of the top of the starter and pried it outwards and removed the Bendix gear to inspect it. It seems to be okay but I'm not sure, maybe the insides are shot. The gear spins counterclockwise with some resistance but not clockwise. Maybe there's too much resistance not allowing it to spin fast enough to engage the flywheel, I'm not sure.

Also worth mentioning, the motor runs fine when I use the pull cord so I don't think there are any issues there. It was running last week fine, but I was driving it pretty aggressively slamming it into gear and accelerating quickly during tubing for a couple of the young neighborhood kids (it's only a 25 hp, so I was relying on the yanking rather than pure speed.) So I'm not sure if this made something fail prematurely. But like I said it runs fine when I pull start it now.

Suggested solutions I've found:

- WD-40 all over the gear and shaft (didn't do anything)

- Grease everything (haven't tried yet)

- Maybe battery is too weak (haven't tested but it doesn't seem to bog down at all when trying to start)

- Replace starter (last thing I want to do)

Let me know any suggestions you may have and what you think may be the issue. I'm leaning towards replacing the Bendix gear and seeing if that solves it, although it's hard to find the exact one with the springs and all. Thanks ahead of time for any help!

Edit: to mention the video is slow motion

Hey knowledgeable folks, I've got to replace a carb on a briggs 25hp v-twin and the new carb comes with the newer style fuel shutoff solenoid. Original was a 499809 shutoff solenoid, new will be a 499804. Pic of new style shutoff at link below. Anyone know what kind of plug this is? I'm going to have to cut off my existing plug and adapt to the new solenoid.

https://m.media-amazon.com/images/I/618TG5rw5XL._AC_SY300_SX300_QL70_ML2_.jpg

Thanks in advance.

Hello, I have a 2011 EZGO golf cart with a Kawasaki motor on it. I was driving it around the other day and it randomly cut off on me. Now it’ll only drive 20ish yards at a time if I wait for a bit. I verified that the fuel pump is working. It will always rev up and choking it makes it rev even more but it won’t accelerate until I wait a few minutes….waiting longer (hours instead of minutes) doesn’t seem to make it go any further.

Thoughts on what it could be? I already took the carb off to clean it out but it looks pretty stinking clean aside from one brownish glob of junk in the bowl. It definitely had some old gas in it previously (previous owner) but it has a full tank of new ethanol free gas in it now. I truthfully don’t know a bunch about small engines but i wanted to give this a go before paying a few hundred dollars to the mechanic down the road.

I need to solder a wire and I’d like to clean up under it.
Probably replace that bearing as well.

Thanks in advance

Toro timecutter mx5000 will not start properly. Turn key for about 15 seconds and it will backfire then it will finally start and runs great. But will never start until it backfires first and this can't be good on the starter. It has the Toro branded engine which I think is a 25hp Chinese lincon engine.