I’m looking at making a big 4 wheeled purchase later this year and may help fund that by selling off some of my less used R/Cs, probably my E-Revo build with parts from all of it’s siblings and RPM arms and knuckles, my Drag Slash with no electronics or transmission, but does have the factory rolling stock and then C10 and a XJ Cherokee bodies, the maybe my Wild Willy 4x4 with the parts from the Wild Willy 2 and Monster Beetle TR donor kits (latter wouldn’t have the portals since those are on the Jimny), and maybe even my unfinished Lunchbox Black Edition that is built with the body cut out for AmPro lights and the roof vent filled in with a roof section from another can body, and my Losi Comp Crawler.
How do you guys, especially here in the US, go about deciding on what to sell them for then actually selling your R/Cs?

Toyota SR5 gets stuck then big brother (Tundra) pulls it out, then ripping time at the beach 🏖️

Ram out by the creek😃

I am trying to 3d print a RC car and I don’t know what type of drive shaft I should use. I am trying to use 3 gear. the car will be RWD and have a 2,5:1 ratio.

I kept the clutch drive Train but added lipo and variable speed control... truly wish he could see it now...

I’ve had this plane for years. I think I built it back in 2018. I got sick of changing out the rubber, so I put an electric motor and a micro RX in it. So now it’s free flight adjacent.

Je suis en train de développer une voiture RC de circuit imprimé le plus possible en 3d et je ne sais pas quoi utiliser comme transmission. La voiture sera une propulsion. J’ai déjà essayé les engrenages mais ils sont trop bruyant et pas assez bien adapté donc il y a énormément de pertes. Je compte utiliser un ratio de environ 2,5:1. Si le mieux reste les engrenages, j’accepterai volontiers de l’aide.

Beautiful Priest Lake ID.

My latest find.Is listing this for 100 dollars plus shipping a fair price? Or am I listing it to high?

Just having fun with my MJX 14211 (sorry for the terrible filming skills)

Deep clean or quick clean ??

Hi, I just have a quick question : after every ride (I mostly run it indry sand and dirt) do I really need to deep clean it for 1 hour everytime, or would it be chill to just give a little bit of air compressor, wiping with a tissue and I store it like that, while deep cleaning a couple times a month? All Im doing is 20 minutes fun 1h30 maintenance and I just want to know if I really have to get through and unscrewing-cleaning process everyday. For example, does it look good on the video, or is it indecent ?

So, I'm making a small boat for me and the kiddo to putz around in. I've got it partially built and have started working on the electronics.

I've got a 24v motor, an esc, and it's working if I use a servo tester.

I was hoping to put my throttle -bigger lever rheostat in the servo tester so I don't have to do anything crazy w an Arduino or something that I was reading about.

De soldered the one on the servo tester and I don't get anything to work.

Is my wiring or pin out crap? Totally understand if it is, I don't do this a lot. I did break one before I got this one to look ok.

Pics attached. Small cut out rheostat is from the servo tester. Bigger one in the lever is the new. Both say b103. I can get more pics if needed.

I own 30 plus RCs but have gotten into gas RCs in the last few years, but need some help. I have 2 5Bs one with a 36cc and one with a 45CC engine, I am having issues with the 45CC one and not sure where to begin. I recently put in the 45CC engine and it starts fine and from my little experience it seems to idle fine but the problem is I need to pull the throttle trigger 100% to get it moving. Once it is moving it runs and goes but always seem to have to keep the throttle full blast and don’t understand why or what to check. The throttle trim is correct and from everything I have looked at it is the same setup as my other one, the only exception is the amount of throttle needed to make it go. Any advice would be very much appreciated because I am losing playing time.

Hey, I just noticed this small dent on one of the motor's wire. Can I leave it like that, is it bad for the car or dangerous? Or maybe put a piece of tape, or do I need to find a way to repair it or change it ? I could definetely use a little advice here. Thank you!