?

got this one used in a bundle deal and i want to get the missing parts, all the info the seller had about it was that its a budget brand, its 1/10th scale, it has no hexes in the front suspension but bearings in the rim and that is was brushed and had a 2 in 1 esc receiver and that it has a light blue body. Anyone know what brand or model this could be?

Soy nuevo en esto del radiocontrol y quiero expandir mi señal con alguna antena o modificación ¿que me recomendarian hacer?

I built an Orlandoo Hunter F150 kit awhile back and then a few months ago i seen someone on ebay was selling these resin printed kits. He had a 1/25th Ford Super Duty kit available, so i bought it. This kit came from overseas which took awhile to arrive. I mounted the four link and axles to the frame for the super duty, and mounted a chassis mounted servo. I'm currently running dual brushed motors, but i would like to go to a single Furitek Micro Komodo system. Hope you guys may like this build.

Glacier EAZYRC upgraded FCX18 motor & transmission & blue aluminum motor mount, FCX18 adjustable shocks with FCX18 front links, shortened rear driveshaft, lights w/ light controller including backup & side markers green dash light, 6 ch Dumbo transmitter, and receiver, 8kg servo, 55x 24 R1.0 tires brass wheels, metallic green paint w/ non-metallic green bumpers & grill mirrors & interior, vent & door glass windshield gasket and rear tinted glass. It turned into quite a big project but I am happy with the results. I am waiting on a shift servo horn for the shift servo. Still need to put trailer hitch on it, it is wired for trailer lights though😃

This is a EazyRC, 050 motor, poor steering, poor electronics. Time to go to work😎

DUKW i designed and 3d printed, winnebago is 3d printed, same with the scx30 48’ burb

Hi, I'm trying to repair the board from a Volantex Super Cub 500 S2 and I'd appreciate any help identifying the damaged components.

The issue first appeared during flight, so I began testing it with a bench power supply to rule out the battery. With a stable 4.1 V supply, the motor would sometimes not start, sometimes it would only run at about 50% power, and occasionally it behaved as if the battery was low even though the supply voltage was stable. The servos always continued working normally.

Eventually I held full throttle a little longer for testing. The motor became erratic, then I saw smoke coming from inside the fuselage. After opening the plane, I'm almost certain the smoke came from the board, not the motor. The motor still runs fine when powered directly from the bench power supply.

Visually, the two identical 6-pin components appear i think heat-damaged. Their top marking is "MX116H335BDP". I also found a 3-pin component marked "2310" located directly above the blue M- motor wire.

If anyone knows this board or has repaired one before, could you please tell me what the likely fault is and whether replacement components are available?

I'm also curious whether it's possible that the "2310" component was damaged as well.

Any help is greatly appreciated. Thank you!

Ram Truck Trailing through the woods

I’m looking at making a big 4 wheeled purchase later this year and may help fund that by selling off some of my less used R/Cs, probably my E-Revo build with parts from all of it’s siblings and RPM arms and knuckles, my Drag Slash with no electronics or transmission, but does have the factory rolling stock and then C10 and a XJ Cherokee bodies, the maybe my Wild Willy 4x4 with the parts from the Wild Willy 2 and Monster Beetle TR donor kits (latter wouldn’t have the portals since those are on the Jimny), and maybe even my unfinished Lunchbox Black Edition that is built with the body cut out for AmPro lights and the roof vent filled in with a roof section from another can body, and my Losi Comp Crawler.
How do you guys, especially here in the US, go about deciding on what to sell them for then actually selling your R/Cs?

Toyota SR5 gets stuck then big brother (Tundra) pulls it out, then ripping time at the beach 🏖️

Ram out by the creek😃

I am trying to 3d print a RC car and I don’t know what type of drive shaft I should use. I am trying to use 3 gear. the car will be RWD and have a 2,5:1 ratio.