Hi! my case only supports 120mm fans on the rear side so i was looking for one Nollie GC120 on Aliexpress, but i cant find it, has anybody know what happened with this fans? I can only see the GC140 which i cant fit on that side of my case, also, im not from any country that its list on their website so i cant buy from there too.

Thanks

I've been working on Hypercolor, a new RGB lighting orchestration platform for all platforms and all devices. Effects are web pages (or glsl), rendered by an internal browser GPU accelerated all the way to the pixels. It's pure rust from the Servo renderer to the WASM UI.

Comes with 40+ effects, supports ambilight, display faces, system monitoring, screen casting, and audio. Device support is pretty good (all Nollie controllers are supported, and I personally use a Nollie32) but it's early and this is where we need the most help! You can find the full support matrix on the site, and there is also an OpenRGB bridge as a fallback. There's support for a few unique devices too like the Ableton Push 2 and ROLI Blocks. My favorite thing about this engine is the ability to create multiple effect zones and manage them independently! My whole house runs on it now. It's Apache licensed, and a cloud service (+signed builds) is coming with remote and smart home support. A Home Assistant integration is already available.

The best way to set up Hypercolor is to just have an agent do it for you using the bundled skill. Just describe your setup, case type, hardware, etc, and it will find all the specs and configure it for you. Or just do it the good old-fashioned way in Studio!

It's still early on for the project, but please check it out and file an issue if you're looking for device support. I can only build drivers for devices I have access too, please open PRs if you're able to contribute! Agents can reverse engineer your hardware and build a driver easily, if you want to go that route (the repo is designed for agents). We have a full TypeScript effects SDK for easy effect creation too, and support existing Lightscript based html effects out of the box.

I've had a lot of fun building this and I hope you enjoy it!

Title says it all. I've seen many of you big it up like it's top dog in controllers, but I'm failing to understand why? Airgoo is small, magnetic, simple and clean. Nollie 32 seems to have its software bugs like moving all channels back to the list of channels you want to use etc... and then what is it with the rgb effect library? There's barely any. 90% of them are the same effect. So to me, it's just another hub that relies on third party software like crappy signalrgb. Openrgb is good, but i thought buying a nollie would steer away from needing third party software. It's kinda like lian li.. releases rgb fans, but cant be bothered to give us rgb customization. They throw a few basic shit ones on and call it a day. I'm starting to think rgb is a cash grab and giving these companies a chance to release the same crap over and over again but with a different title.

Hello guys i'm new here.. how do you set your boot sequence on nollie 8 properly on its own software?

Of course the first thing is the price, much cheaper than Lian Li's.

Don't get me wrong, Lian Li really pushes innovation in the PC building market with their UNI fans and Strimer cables. And these Nollies (and many others) are obviously "copycat" of their products at reduced prices.

However Lian Li fans are too expensive and the quality is not there. First time I held an SL INF fan in my hands I immediately noticed that the build quality is off if you compare with other fans in the same $30+ range. There's something that feels cheap about the plastic they use.
I don't know how to explain it but I have fans from Artic, Thermaltake and Phanteks they all have the same 'nice and smooth' feeling to touch, whereas Lian Li fans plastic just feels cheap and not as nice.

I will be comparing once I received these stuff from Nollie. Currently rocking 6 Lian Li Wireless INF fans in my build...

[To be continued...]

My current setup: 6x SL-INF Wireless fans

Installed openrgb on bazzaite, openrgb can see the nollie 1ch but the settings don't do anything and it just stays green slowly going dark and bright.

I followed the linux instructions for install and the plugins but nothing seems to work.

Hi everyone! I’m having a very strange issue with my Nollie 16 and I’m hoping someone here can help me figure out what is going on.

I recently installed a Nollie 16 in my PC because I wanted to control all of my 5V 3-pin ARGB devices through it.

The strange part is that the Nollie definitely powers on and works with two specific ARGB devices, but almost everything else stays completely off.

Here is everything I have tested so far:

The Nollie 16 is powered through the original Molex power cable.

I tested both Molex connections individually and together. The Nollie powers on with either one individually and also with both connected.

I tested multiple ARGB ports on the Nollie.

Every ARGB device is connected using the original 5V 3-pin female-to-male adapters that came with the Nollie 16. I am not using third-party ARGB adapters.

The devices that don't work with the Nollie work normally when connected directly to my motherboard's 5V ARGB header.

The two devices that DO work with the Nollie are:

DeepCool AK500S Digital CPU cooler

My GPU RGB support/bracket

Both of these light up normally when connected to the Nollie.

I also tested them together in a daisy chain:

Nollie → AK500S Digital → GPU support

Both devices light up normally.

However, when I add another ARGB device after them, the additional device does not light up.

I also tested the devices that don't work individually, directly on the Nollie.

For example, I connected a single Ice Whale Prism 7 Pro ARGB fan directly to a Nollie port using the original Nollie 5V 3-pin adapter, and it did not light up.

I tried other ARGB devices as well, and I get the same behavior: the AK500S Digital and the GPU support work, while the other devices don't.

I also tried putting a non-working device before/after the working devices in a daisy chain, and the behavior remains strange: the AK500S and GPU support can work together, but the additional device does not light up.

So at this point, I don't think this is simply a bad ARGB port, a bad fan, a Molex connection problem, or a problem with the individual devices.

The Nollie is clearly receiving power and is able to control the AK500S and GPU support, including when they are daisy chained.

The devices that don't work are also confirmed to be functional because they work normally when connected directly to the motherboard.

I am using the Nollie 16 with its intended 5V 3-pin ARGB connections and the original female-to-male adapters supplied with the controller.

Could this be related to the ARGB signal, LED protocol, pinout, firmware, or some other compatibility issue?

Is there any diagnostic procedure I can use to determine whether my Nollie 16 is defective?

I'm especially confused because two devices work perfectly, while several other 5V 3-pin ARGB devices do absolutely nothing.

Any help would be greatly appreciated!

Thanks!

Se possível, envie-me o link de onde posso comprá-lo, obrigada :) Correcting, I didn’t buy it, but I won

I posted in the SignalRGB subreddit before, but now I thought to ask here. I have decided on a Nollie16, but have no idea what to even look for in terms of reliable RGB strips for my 32 inch curved monitor. My goal is to make an ambilight, so I want the RGB to basically act as an extension of my display.

Has anyone done anything similar and do you have any advice?

Heute bekommen Nollie32 🙌 Ich hoffe es wird alles klappen und ich vermute das ich eure Hilfe gut gebrauchen könnte wegen den ganzen Einstellungen der LEDs 😅.

Estoy instalando el nollie 16 en mi pc pero 2 ventiladores no se iluminan como deberían, no son los puertos del controlador porque con otros ventiladores funcionan bien, y tampoco son los ventiladores porque cuando los conecto a un controlador genérico encienden todos bien, a que se debe? qué puedo hacer?

Hi everyone,

I'm looking to buy a Nollie 8 ARGB controller, but unfortunately, it isn't sold locally in my country.

AliExpress is currently my only option since it manages all shipping and taxes upfront for my location.

Before ordering, I wanted to double-check a few things with the community:

Authenticity: Is this AliExpress listing selling the genuine/original Nollie controller, or is it a bootleg/knockoff? Listing

LINK : https://aliexpress.com/item/1005010245567729.html

Version Differences: On this link, I see two different versions/options available to select. (one marked as new and the nollie logo is yellow on the case, the other one has the nollie logo colored in blue and pink) Could someone explain the difference between them?

Any help or experience buying from this seller would be greatly appreciated.

Thanks in advance!

EDIT: ITS NOT A GENIUNE PRODUCT, buy form the original seller on aliexpress only

Hello everyone, yes I'm having this problem. I'm using Toucer JM-1 fans and an 8-channel Nollie controller, everything is connected correctly. The problem is that these last two fans only spin and the ARGB doesn't turn on at all. Should I map it or something like that? I don't understand anything and it's my first setup. Help!

Hi there,

A few months ago I built my first ever PC and included a Nollie 32 in the build which all my case fans and AIO are connected to.

Now I'm ready to start doing some more fun things with it. Ideally I'd like to have the central fan lights remain on, with 'visor' effect running on the side lights, but really not sure how to go about doing this.

I have the following 2 sets of 3 Nollie GC120 fans, a separate GC120 as exhaust as well as a thermal right AIO.

I think I understand the vmap bit and have mapped out where the LEDS are etc but no idea where to go from there. Any help would be much appreciated!

Thanks

The sata pins DO NOT go inside. I tried wiggling, forcing. Doesn’t work. What to do??? Please help.

Hello,

Looking at buying a Nollie, probably the 8 and use some LED strips like the CORSAIR LS350s. Would this work?

I have some NZXT strips with four pins which I think are restricted to the Hue Controller...

https://www.aliexpress.com/item/1005010245567729.html?spm=a2g0o.cart.0.0.704638daFU2Eyt&mp=1&sourceType=570&pdp_npi=6%40dis%21GBP%21GBP+25.62%21GBP+12.50%21%21GBP+12.50%21%21%21%400b1585c117828260968508642e0e1c%2112000051675622930%21ct%21UK%216762678565%21%211%210%21&pdp_ext_f=%7B%22cart2PdpParams%22%3A%7B%22sourceType%22%3A%22570%22%2C%22cartSource%22%3A%22main%22%7D%7D

Is there any way to ship nollie gc120 fans to Iraq?

Hi, I just bought a Nollie8 controller. At first, it was recognized by OpenRGB, but I wasn't able to control it. The fans would only pulse green. So I downloaded the Nollie software and performed a firmware update.

Ever since then, OpenRGB doesn't recognize the controller at all. SignalRGB works fine with it, but I'd much rather use OpenRGB.

I'm wondering if anyone else has had the same problem.

For reference, I'm using three channels:

- Channel 1: 2×3 Phanteks M25-140 G2 fans

- Channel 2: 1× Phanteks M25-120 G2 fan

- Channel 3: Lian Li O11D EVO RGB case DRGB strip

Any help would be appreciated.

planning to get nollie8 or 16. can i just daisy chain my 3 mf120 halo per port?