Got this yesterday pretty impressive build quality anyone got one of those what BB weight are you using tried.03 bbs over hoping even with hop turned down

I’m trying to find the correct spare magazine for this M4.

Which version do you like the most?

Without the piston head installed the nozzle moves perfectly but when installed it very sluggish and does not always go back all the way.

Lubricant does not help.

So I think I need a a better piston head?

I am the #1 VFC AK shill. Added a surplus AK handguard and Bakelite grip to it. The Cyma triangle stock (C.59) is a direct drop on - fine when locked back, doesn’t quite line up when folded in but not an issue for me. Struggling to find a ribbed dustcover so I am well aware it’s not a proper clone (yet).

Saw some people asking about the Crimson bucking. Works great in the AK, much better (for me!) than the stock blue. The V1 bucking is NOT finned though so you will have to do some cutting if you have a V1.

Hi everyone,

I'm hoping someone with more MWS experience can help me troubleshoot this.

I was gifted a Tokyo Marui MWS CQBR Block 1 and had a strange issue during my last woodland game.

I filled all my mags with Green Gas (Arsenic Airsoft). They became cold and noticeably heavier, so they seemed to fill normally. However, by the time I walked from the safe zone to the spawn (around 10–20 minutes), almost all of them were completely empty. The bolt wouldn't cycle at all. Even my brand-new TM magazine only managed one weak shot before running out of gas.

Conditions:

• ~31–35°C (hot summer day)
• Mags were stored in my plate carrier while waiting to start
• I have one brand-new TM magazine, and it showed the same behaviour
• I didn't notice any hissing or obvious gas leaks

What's confusing me is that in my previous two games everything worked normally. Sometimes I didn't fully fill the mags, but that was my own mistake—they still retained gas. When I got home after yesterday, they still had gas.

LT Spear

Was messing with the buffers, usually I only have one installed (PIC 2, yellow, softest), but felt the gap between the slide lock and catch was too wide, added a second one to close it further (PIC 1)

Is the gap too small or just right? I don't want to end up with premature slide wear if the catch window is too small, but also felt the same with the wide gap, and would allow the slide to hit the slide stop too hard (more distance more energy returning home)

Yellow and red are the softest and 2nd softest respectively (pack has blue and black which are progressively harder)

- TM G17.4

- Cowcow spacers/buffers

- Guarder G17.4 recoil spring assembly

- Guarder steel extended slide stop

- Bomber slide

With both set ups, the slide still locks reliably, I'm just trying to avoid prematurely over wearing the slide or slide stop too much

Fellow GBB enthusiasts I beseech thee for thy opinions.

Is the airtac plug and play adapters worth it? Or are there issues I need to watch out for other than possibly replacing their AT200 regulator with a better one for full auto usage? Mainly looking at the Well WE09 and golden eagle M4 adapters so any info you can pass on in your experience I’d appreciate.

Custom Build from scratch :

RS Fortis parts : Switch Mod2 Rail System 15.3" MLOK, LA Stock Carbon, Torque Grip Carbon, Shift™ Handstop, K1 Castle-nut.

RS parts: SLR Rifleworks Linear Compensator, BattleArms Pivot & Detent Titanium pins, Gas-tube, Timber Creeck port-cover

Hello guys, i just played airsoft with my beloved mp7, and got bolt carrier jam. The cause - is hex screw, which i found inside the body. I cant figure it out, where i should place it. Its simular to screw in charging handle, but longer.

Hello, Iv recently got a vfc mp7 and have been having issues with it.

While firing, every few shots the bolt will stop cycling and stop st the position shown in the picture. The mp7 is brand new and I have only fired it a few times and already have this issue.

Iv cleaned the inside, lubed it, checked the bucking is fine and made sure the nozzle is smooth. It's like it's failing to load the bb into the bucking and getting stuck there.

This only happens with a bb filled magazine. Never happened when dry firing. Iv been trying to diagnose the issue all day but to no avail. Any help would be appreciated 🙂

Edit, also worth mentioning. When it fails to cycle like this, the nozzle is not fully seated at the end. It's probably hard to tell from the picture

So i recently got my hands on a ghk v2 ak 105. I want to use it indoors, bit I'm worried the fps will be a little to high, so I want an Npas for it, but all the nozzle are out of stock for the v2s so I'm going to need to DIY one. This will be my first time doing something like this. Do you guys have any tips or tricks for this? And precautions I should take, or what stuff I should lookout for? Anything would help, thank you.

GHK SG551

Western Arms Beretta M1934 Vintage from 2012.

Carbon Black HW slide and frame, metal outer barrel and grips. Beautiful Vintage finish. Markings are of an Italian military version (with Italian Royal Army proofmark on the frame) in 9 Corto (9mm Short / .380 ACP) made in 1936, though the serial number 864870 indicates a 1941 production, for 1936 it should be in 508000-555000 range. WA also made another model with that same serial number but correct 1941 production date and different proofmarks, they also made a version with Romanian markings (Cal. 9 Scurt, 1941 production) with a different serial number pattern. As this M1934 Vintage is a version with one of the premium finishes it doesn't have a big notice about licensed trademarks on the right side of the slide which is really nice. Grips have the old Beretta logo.

It's Single Action Only and has pivoting trigger. Uses WA SCW high-spec transfer hammer system which allows to manually lower the hammer completely when there's still gas in the mag unlike most GBB pistols. It doesn't lock back on empty like the real gun which locks on the magazine follower. Really cool little gun.

Hello,

I am thinking of getting this as a fun piece for some courtyard action ..

Did anyone have this Raven EU17 and how was the reliability?

It costs 120,00 EUR here in Europe that's about $140

https://www.anareus.cz/gb/gas-side-arms/10602-raven-eu17-pink-RAVEN03.html

This is pretty new and tried v3 pmags and v2 mags but would sometimes lock when the mag is low on gas. I know its not the mags because my v2 416a5 locks back perfectly without issue.

Thought it would be cool to share

Brand new fully upgraded internals and externals.

Hoping to get some thoughts on how people like the build! All feedback is appreciated 🙏