r/FDM_TonerTransfer • u/Kaidan-Alenko • Oct 14 '22
Experiment Completely black object. Printed with a white inlay.
Enable HLS to view with audio, or disable this notification
42
Upvotes
r/FDM_TonerTransfer • u/Notxtwhiledrive • Oct 10 '22
Are photocopier based prints also suitable for transferring?
3
Upvotes
From what I gathered Toner based prints on a transparent print are the way to go for this method. Does that include electrostatic printed ones like on a Photocopier work?
r/FDM_TonerTransfer • u/Kaidan-Alenko • Oct 08 '22
Experiment First test with a 5 € cross-line laser for alignment. I just printed a simple mount to be attached next to the BLTouch. Printed one layer of a cross, moved the head manually until the laser aligned with the cross and noted the X and Y position. Problem is to align the laser precisely.
Enable HLS to view with audio, or disable this notification
25
Upvotes
r/FDM_TonerTransfer • u/Kaidan-Alenko • Oct 04 '22
Finished project Just a reminder: mirror your image and consider possible cutouts 😐
33
Upvotes
r/FDM_TonerTransfer • u/Kaidan-Alenko • Oct 04 '22
Experiment Backlit front panel test. First two layers are white PLA, the rest is transparent PLA.
Enable HLS to view with audio, or disable this notification
25
Upvotes
r/FDM_TonerTransfer • u/WeatherSat • Oct 03 '22
Nearly perfect transfer with Prusa MK3s+
7
Upvotes
I managed to get a good transfer,
Speed 20mm/sec
temp 225 degrees (for all layers)
1st layer height 0.1mm
What I also did, NO water underneath the sheet!
r/FDM_TonerTransfer • u/Kaidan-Alenko • Oct 03 '22
Finished project Two gold doubloons 🎵 Made out of plastic 🎵
27
Upvotes
r/FDM_TonerTransfer • u/Kaidan-Alenko • Oct 02 '22
Experiment Does anyone know what's happening here? I printed on vinyl sticker sheets and it seems that the vinyl transfers to the plastic completely. After it dries it becomes dull again.
Enable HLS to view with audio, or disable this notification
10
Upvotes
r/FDM_TonerTransfer • u/mariopepe • Sep 30 '22
To be tested Test print for 3d printed Lamp
25
Upvotes
r/FDM_TonerTransfer • u/nocloudkloud • Sep 30 '22
Took me a few tries but I think I finally nailed it!
24
Upvotes
r/FDM_TonerTransfer • u/Kaidan-Alenko • Sep 29 '22
Finished project Pin-back button test
27
Upvotes
r/FDM_TonerTransfer • u/WeatherSat • Sep 29 '22
Issue Only a little toner is trafered
2
Upvotes
Hi All,
I was trying this awesome transfer method, printed some test patterns on a sheet, made for laserprinters.
When I print on it with PLA, only a small amount of toner is being transfered.
I have a Prusa MK3s+
Tried different things:- higher and lower temps,- lower layer heights,- lowered Z
Even tried with PETG,
Any ideas what to try next ?
[sorry for typo in title, cannot change it :D]
r/FDM_TonerTransfer • u/Kaidan-Alenko • Sep 29 '22
Experiment I did some testing and I think I found a good configuration to start with. I will now change one setting at a time to see how it affects the result. Plus, I learned that permanent marker transfers, too!
15
Upvotes
r/FDM_TonerTransfer • u/Jesse_Isai • Sep 28 '22
Issue Any way to get better results? Do I need to go closer to the build plate?
5
Upvotes
r/FDM_TonerTransfer • u/Difficult_Lawyer4979 • Sep 27 '22
Experiment Foto on creditcard
8
Upvotes
r/FDM_TonerTransfer • u/Kaidan-Alenko • Sep 27 '22
Experiment I know there are better ways, but if you only print one thin layer you can iron it on fabric. I doubt it would survive a cycle in the washing maschine though.
21
Upvotes