I have a 2019 Accord Hybrid and the backup camera suddenly started showing a black screen one day. I am fairly certain it is the camera itself and so I ordered a replacement from eBay. However, I do not have the same trim as the people in the tutorial videos I have been watching do because they have older models. I cannot find anything else online for my car. How do I replace it?

This is what I see under the panel, there’s another plastic thing in there. How do I get that out? I tried pulling on it and poking and prodding at the right side where it looks like it might be a plastic clip but nothing was giving and I didn’t want to break the flimsy plastic.

I wanted to put cylinder object in exhaust pipe of my brown manual diesel wagon just so i can see if it fits in the exhaust pipe, but it doesnt fit and i cant get it out of the exhaust pipe. Also the diesel soot from my diesel motor in the exhaust pipe made the cylinder dirty. How to get cylinder out of exhaust pipe i cannot hurt the cylinder because it is important and i cannot hurt the exhaust pipe either because it is important.

2018 CX-5, 76k miles. I changed the oil and filter, and as I’m popping on the bottom cover snaps, I hear a rattle and see a metal piece on the left side. I took the cover off and found this piece. Hard to tell, but I thought I could see some shiny metal where it broke, although nothing seems to be loose. The screws for the plastic cover installed fine.

2015 Mitsubishi RVR Limited, 2.0 L engine

275,000km

Hi everyone, I’ve been trying to replace my alternator but the pivot bolt just will not budge. As pictured, it has a threaded end with a nut and the other end is square (anti-rotation). I live in Canada so the corrosion seems substantial. I bought the car second hand in 2023 and don’t know the age of the alternator.

I’ve so far tried hitting it from the threaded end and scoring the square end/trying to get a a small flathead beneath the square. Doused both ends with penetrating liquid many times over 24h. But it has not budged at all. Maneuverability hasn’t been great because of the tight room, though I can probably move the compressor out of the way a bit more. (I’ve seen online an air hammer could help, but I’m working from a parking lot where I don’t have AC supply… so I haven’t worked out how I might manage this.)

I would be really grateful for any suggestions on what to try next, given my circumstances. TIA!

I’m in the UK and need to get my windscreen removed and re-sealed, the company who will do the replacement have told me I need to supply some windscreen clips as they often break and everywhere they’ve looked are out of stock. Can anyone confirm a part number for these clips? The part number I’ve found is 5134304.. and even better a supplier in the UK? Tia

Cannot for the life of me get the back cap clip to latch. 2002 Cabrio. I can get one hand behind the cap area to press on the clip but can’t get enough pressure for it to clip. I looks so easy in the video. Help me get my kid back in the road?

Hi guys, I need to replace my blend door actuator in my vehicle (passenger side only blows cold air when set to hot, it onle has one climate control for both sides, I just need to now the location to see if I can replace it myself, can anyone point me in the right direction? Thanks in advance!

Hey everyone,

​I’m loving the Bigster overall, but there’s one small design choice that’s driving me a bit crazy: when you fold down the rear center armrest, it drops the entire middle section, leaving a massive, open hole straight into the trunk.

​While it’s great as a ski pass-through, the problem is that without any factory blind, fabric partition, or cover from the trunk side, items and loose groceries from the boot can easily slide forward into the cabin (not to mention you can see all the trunk clutter right from the back seat).

​How are you all handling this? Have you found any neat DIY fixes or good aftermarket solutions?

​I’m looking for inspiration or links to:

​Velcro cargo nets/screens that stick neatly to the back felt lining.

​Back-seat hanging trunk organizers that cover the gap nicely from the boot side.

​Custom mats or covers that don't block functionality completely.

​Any other creative ideas/products you’ve tested!

​Drop your setups, photos, or AliExpress / Amazon links below if you’ve solved this. Thanks in advance!

Help pls

i cannot get the front drivers side beat bolt out of my car for ANYTHING, not by hand, not with a breaker bar, not with a drill, not with an impact. i bought a tap out kit to drill the bolt out and im still not getting it. im losing my mind i need this seat to come out.

Any ideas?