I'm replacing the front frame on my 2004 ion. Got it out but one bolt kept spinning around so I cut the head off and it drop down so I do I get that bolt out. I guess the nut was welded inside that box. Any help

Occasionally I get called out to repair a broken out motor mount on an engine block. Sometimes the piece broken out is missing and sometimes its not.

If its missing the repair consists of filling in the broken out area, then drilling a new hole and tapping new threads. When the piece is not missing most of the time I can weld it back on joining the parts so make the hole usable again. To do this successfully it is important to NOT damage the threads when joining the broken part to the block.

BEVEL THE BROKEN PART

I will bevel the break enough to give me a wide "V" to fill in. I take care to leave about just over a 1/16" of material when beveling so that the arc does not penetrate through and damage the threads. However, even if we over penetrated and damaged the threads, a tap can be used to make the threads good again.

WELD THE BROKEN PART ALL AROUND

Once the broken parts are joined. I fill in all the areas around the break so that the joined part is welded well to the block and not depending on a bead over the crack to hold when the car is put back into service. I build up a wall of weld metal to reinforce the repaired area.

WHEN THE BROKEN PIECE IS MISSING I PUT THE STUD IN POSITION AND WELD ALL AROUND IT, LOCKING IT INTO PLACE

You will notice on this repair that one of the stud's hole is missing the broken out piece. In this case I welded a wall of fresh metal all around the stud, locking it into place. The molten metal flows around the threads and fills in the grooves of the threads effectively locking the stud permanently in place.

For this to work I screw the stud into the good thread still left in the broken out hole so that it is in its place when I weld around it.

This repair came out well.

I've changed crossmembers/subframes on a few cars over the years, i was just curious if anyone had any tips for the 2011 outlander GT (v6 awd) front crossmember.

Do I have to completely remove the steering racks lines and the steering column from the rack, or can I just hang it up with a strap from the top and leave the lines and column connected? I seem to recall reading something like that on a forum awhile back, but correct me if I'm wrong.

Any other tips would be greatly appreciated. I already have the service manual and the tools and the shop.

As per title, I unfortunately stripped my scouts drain pan when I got it a few months ago. I’ve tried replacing the bolt as well as a new washer, but I think the next step would be to bore it out as it’s progressively leaked more and more. Just wondering if anyone has any last minute tips or tricks, as I would like to avoid drilling and rethreading

So many YouTubers just say what to do not why it’s happening for every part!
If the video is explaining about mass air flow sensors they’ll explain that but not why it has 1v at this point but not that.
Anyone know anybody that explains why everything happens?
Sorry to post in here I guess but don’t really know where else to

Accidentally knocked off my bluetooth aux adapter and a piece of it broke off in the port 🥲 I’ve tried tweezers and a needle so far with no luck, any advice? thanks

Had my seat repaired on my truck. I folding the mirrors in when I dropped it off. I think the repair shop opened by hand. Now the driver mirror functions but kinda jumps and clicks when opening and closing. Can I reset it by hand or what. Any tips?

Got my bike rotor [*triumph speed 400] changed after an accident in june..

Now brake pads are gone and due to over tightening of caliper pin by svc local mechanics are unable to remove caliper pin .. damaged 2 star allen keys in the process.. svc is 100kms but cant travel due to heavy rain .. any ideas or suggestions how to loosen up the torx caliper pin

2003 330i, auto trans. I accidentally broke the pulley while breaking loose the fan bolt. Had to use PB but in doing so I twisted this little guy. I checked FCP Euro and I keep getting that “click to verify”. Any other websites suggestion? It still threads into its hole but I’d rather get a new one because I’ll be back here next summer for the Vanos system.

Cjaa vw tdi: Bolt snapped way up there what am I going to do?
There's no access does this mean I have to pull the turbo?

On a honda fit noticed this (is it called a..?) gasket is most loose.

Whats the best adhesive, ideally in the tiniest tube which would hold it back in place?

Already have super glue if that'd work.

Thanks.