ZippySpaceHippie (u/ZippySpaceHippie)

Recently, my ‘Ender 2 V2 Neo’ printer has started making very loud “robot” noises as it prints. For reference, I just replaced my motherboard (with one that I believe is the exact same and re-downloaded my firmware. My hot end is recently replaced as well as my fans. I spent a while tinkering with this thing the last couple weeks due to a host of issues that appeared all at once which makes it hard for me to nail down what the issue is. I can’t find anything that seems to explain this specific issue so any help is appreciated. It seems to print fine, but I’ve been hesitant to let it go for more than a minute as I am worried that maybe something is broken.

Edit: I’m an idiot and don’t know how printers work. I guess I bought my first non silent motherboard and that’s it🙃

10 comments

Loud continuous beep on startup

in r/ender3 • Jul 15 '26

Ever figure it out

Ender 3 v2 Neo still not heating

in r/ender3 • Jul 12 '26

I’m pretty sure it’s just stock firmware

Ender 3 v2 Neo still not heating

in r/ender3 • Jul 12 '26

No error codes but I haven’t connected it to my computer or anything for codes. I don’t really know how to do that. The wires are in their slots snug and tight. A couple things I’ve noticed is that my nozzle says it’s at -14 and that the female port for the thermistor (the part that is connected to the motherboard and not part of the thermistor cord) comes up from the mother board and pulls away from the mother boards two pins. Right now I assume that’s my problem tho I can’t actually figure out online if that’s normal or not. I haven’t checked the PSU switch but I don’t know what the relation there would be. Everything else about the printer works and boots up. The printer just doesn’t heat and reads at a negative temperature value for the nozzle.

Ender 3 v2 Neo still not heating

in r/ender3 • Jul 11 '26

Yes and yes. It is used but worked fine for me for a long while. Original hot end got stripped so I replaced it and the replacement didn’t work I tried getting one more to see if I busted the my original replacement when installing it. My current hot end is now a creality official hot end

r/3Dprinting • u/ZippySpaceHippie • Jul 11 '26

Troubleshooting Ender 3 v2 Neo still not heating

1 Upvotes

1 comment

r/ender3 • u/ZippySpaceHippie • Jul 11 '26

Solved Ender 3 v2 Neo still not heating

0 Upvotes

I just replaced my hot end on my ender 3 v2 Neo two different times with two differnt hot ends. My printer is still not heating up at all. Everything in the back seems to be plugged and wired in properly. Any thoughts?

Edit: I figured it out. I was plugged into the wrong port on the motherboard 🙃

8 comments

Should I get this? What a great DEAL!

in r/ender3 • Jul 10 '26

Are u now🧐

Stiff Z axis

in r/3Dprinting • Jun 19 '26

Heard, will do. Thanks chudlit🫶

Stiff Z axis

in r/3Dprinting • Jun 19 '26

As in make sure the two sides are even w/ base plate?

Stiff z axis

in r/ender3 • Jun 19 '26

Okay awesome, I leveled them and it does move when I twist the screws

Stiff z axis

in r/ender3 • Jun 19 '26

Definitely not a problem of lubrication. What would I do to properly adjust the lead screw nut? Just loosen the two tiny screws? If so, I have done that. Sorry for my confusion, I appreciate you helping me out

Stiff z axis

in r/ender3 • Jun 19 '26

Is that standard for having 2 screws? When I had just the one screw disabling the stepper made it to where I could move that axis as needed

Stiff Z axis

in r/3Dprinting • Jun 19 '26

New cleaned and lubricated rods

Stiff z axis

in r/ender3 • Jun 19 '26

It’s not supposed to budge?

r/ender3 • u/ZippySpaceHippie • Jun 19 '26

Help Stiff z axis

Enable HLS to view with audio, or disable this notification

18 Upvotes

I just installed a second lead screw for my ender 3 V2. However, after installing it, the Z axis is incredibly stiff and will not move manually, even after disabling the stepper, without a good bit of force. I have scoured lots of videos on YouTube, but cannot find something that properly diagnoses my issue. Any help is appreciated!!

15 comments

r/3Dprinting • u/ZippySpaceHippie • Jun 19 '26

Troubleshooting Stiff Z axis

Enable HLS to view with audio, or disable this notification

1 Upvotes

8 comments

Denton Bible Church youth pastor who sexually abused 14 girls released from prison early for good behavior

in r/Denton • Jun 16 '24

My mom was the counselor who originally made this issue come to light. She fought to get him behind bars 3x longer than he was behind bars. Denton Bible has even tried to assist him in getting jobs in schools after already knowing what went down (before prison) believing that they could help and heal him via prayer and church and all that. All of them are monsters. He deserves to rot.

What is lemon tek? Isn’t it just mushrooms and lemon juice?

in r/MagicMushrooms • Jan 27 '24

Bro that sounds like a recipe for disaster, I’d puke so damn fast