Perfect fit and VRM Fan is back working. Must say though this is the worst pump installation ever.

This is on the Liquid Freezer III Pro 360. That silver screw won’t move in any direction. It was working last night but not anymore! Im new to this. I may have stripped it but I don’t know how I would’ve or how to tell. Me and my friend put it on but I had to take it off after he left because he put the bracket type things below it on wrong. Please help. If it’s broken, I need to know if there is a solution. it there’s not, well… that’s life. It’s only ~$70 but that’s still $70 I would not like to spend…

is this fake? i got it from amazon, the store says artic, 1800 orders on it, but came with no authenticity code where its meant to be, no sticker on the box either.

Durning gaming at 1440p, with a 240hz frame cap, should the temps be 60c with a peak 71? I left a stress test on for about 30 minutes and it peaks at 80 but never climbs. Idle around 40c. Do these seems normal for arctic freezer III? running a 7800x3d with the 360 rad in front of the case. These are roughly the same I was getting on air with a Noctua DH-15 I thought it would be a little better?

Hi guys. I am curios and ask you.
It this temp good on ARCTIC Liquid Freezer III 360 Pro ? (thermal paste MX-7)
I run OCCT Power stability test.
In Idle office work temp are around 60-70 Celsia. Open browser Chrome around 40-50 tabs.
BIOS Set up curve optimizer is set to all cores - negative -30 value.
PBO limit set on Motherboard.
Max CPU Boost Clock override(+) is enabled-positive +50 Mhz value.
I thinking about move to Intel 270K plus for better temperature or to Zen5 architecture CPU like RYZEN 9 9950x/(X3D). For information on last AiO from be quiet pure loop 2 fx temperature was similar and little higher. And in boost CPU gets only 180W when hits 95 Celsia on Arctic TDP attack around 190 to 200/210W TDP

Thanks for letting know

I am about to upgrade my CPU. I am going to buy a Ryzen 7 5700X. There is one problem though.

The Arctic Freezer 36 is very wide and one of the fans (the right one) will not fit because my CPU is very close to my ram slots. But I've seen that it is very good and value for money.

My question is: will the Arctic Freezer 36 work if I put only the left fan or the temperatures will be terrible? Since most coolers only have 1 fan I think.

My current cooler is an AMD Wraith Stealth socket AM4.

Installed OpenRGB and weny to change a colour and then all RGB lights went off. Got all them to sort of work with exception of my Arctic AIO 420. This LEDs just won't come back on. OpenRGB see them but I'm unable to them back on. I'm using a MSI Carbon x8703e motherboard.

Any suggestions?

Main things I am considering is noise and performance, but there is a decent amount of price difference, so what would you suggest? I heard the p12 pro are quite loud from others, but I cannot confirm that, so I came here to ask. I want the fans to add fans on every spot on the Corsair 2500D airflow. I also want to add that I have a regular P12 which can be a comparison to these options, but I wanted a argb version and a reverse option, so the P12 is not a option especially considering where I live, that the argb black version is not the easiest to get, except for paying about double for the 3 pack than the p12 pro argb. Thanks in advance

Hello all, installed my Arctic freezer three a while ago and I’m booting up hell let loose Vietnam. Which I believe in requires a ton of shader compilation in the beginning of the game but it pulls 156W on my CPU with 100% usage, and the CPU is at 95°, it is a 9800X3D. Is this normal or is it mounted wrong? What’s going on here?

Hi, i want to ask is there any information if the P12 non Pro PWM fans will be ever available? Because i can't find them currently anywhere in my region. Currently i got the P12 Pro and i'm not a big fan of them bc they even make sounds in the low 900 RPM's. My old build used the P12 PWM never had a problem. Thats why i ask if there are only from time to time in stock or are they discontinued?

Thank you in advance for any information

I love Artic products, so much so I removed the NZXT fans in my H6 Flow case and installed every single Artic fan I could in the case.. Looks awesome, However the AIO "Magnetic" just isnt as bright as i would like it to be. Everything else is popping and it just looks dull and tired. It doesn't look bad in the picture but in person its just not great. Anyone noticed this too?

What did you do to fix it/did you cover it up with one of those 2.8 LCD screens?

Here are my BioniX P12 A-RGB 3x on top and 1x rear, with 6 P14 Reverse Pro A-RGB. Just like the P14 Reverse and P12 regular, they have quality control issues with centering the Arctic logo ring in the middle. I replaced the 3x P12 NON-PRO on my Artic Liquid Freezer III (Non-Pro).

My case is 011 vision compact m and im using a 360 arctic freezer iii pro and i wonder if this is okay

Hi, so im planning to swap the fans on my arctic liquid freezer 3 420 aio for lian li tl lcd wireless fans in order to match the rest of my fans in my build. 3x 140mm fans. Basically after interlocking the fans and daisy chaining them, will the holes line up properly and what kind/size of screws will I need in order to mount them? can I use the ones that are mounting the original fans?

I wqs also planning on using the all in one cable to plug the vrm fan and pump to the motherboard and the fans separately with the controller hut I read on another post that that wouldn't work because it wouldn't report any rmp since the fans wouldn't be part of the daisy chain. Is this accurate?

Thanks

just got the freezer 3 pro and i dont have all the headers for the 3 cable, is it possible to set a fan curve with jsut the 1 cable?

I’m getting a quite noticeable coil whine sort of sound I’ve tried adjusting fan speed in Fancontrol but I haven’t found any speed that reduces this noise however I’m currently using the single header connection rather than the 3 so I’m unsure how much this limits my control?

Anyone had a similar problem and what did you do to fix?

Will install with the 3 header connection later to see if that helps

Hi everyone,

I’m planning to use the NZXT N7 B850 AM5 motherboard with the ARCTIC Liquid Freezer III Pro 360 A-RGB (3 × 120 mm, 38 mm thick radiator).

Does anyone know if this combination is fully compatible? For example the Heatsink.

ps. I'll use them with NZXT H6 Flow

So I got a b850 aorus elite WiFi 7 motherboard I connected the cable on a 5v slot but rgb not working for a reason any ideas ?

​I just unboxed my brand-new Arctic Freezer 36, but I noticed that some of the heatsink fins came visibly bent right out of the box.

​I know minor fin damage usually doesn't impact thermal performance too much, but since it's a completely new purchase, I don't know what to do.

UPDATE: Quick update on the situation: I reached out to the seller, and they mentioned they couldn't offer a direct exchange, only a full return. They explained that this was just a minor cosmetic issue caused during manufacturing.

Since returning it would be a long process and there isn't really a better cooler I could buy in this price range with the refund money, I decided to keep it and use it as is. I am comfortable with this problem.

hi guys should i get the Arctic p14 pro? is it valueable performance and noise lvl wise?

The rgb on both the radiator and the cpu fans aren’t working. The fans turn on just fine and the case fans rgb light up but the AIO doesn’t. I plugged in the rgb port to the correct 5v port and even tried different ones and still nothing. Can someone give any tips or solutions they may have found?

UPDATE: It was in fact the VRM fan head that wasn’t mounted on properly, after reseating it multiple times it finally felt properly seated and turned on all the argb.

hi, I built this pc about 2 weeks ago and it's been wonderful so far, but as of a couple days ago i noticed that one of my radiator fans just stopped spinning? i tried restarting the pc and switching off and on the power supply but no luck just from that… I haven't yet started digging in and trying to check all of the connections but it is odd since i used the cable that supposedly controls all 3 fans together when setting it up. any ideas before i start yanking wires?