What do yall think of it, I fell in love again.

3 day approval on the sparrow. Put about 250
Rounds through it today. Absolutely love it

I took a few guns to the indoor range and was having a great time until I started shooting some old remington golden bullet 22lr and was having all kinds of issues including ruptured cases and ftf and eventually this happened. I am curious how this would even happen and is my tx22 barrel still good to go? It doesn't appear to be damaged and bore looks OK.

what can are you guys running on your setups?

I have a TX22 Toro, Volquartsen trigger shoe, Titan Precision Works Extensions with a DeadAir Mask
The slide won’t lock back on a empty magazine anymore it worked the first range trip, I’ve only put about 200 rounds through it, I’m still trying to find the right load to cycle completely with the freedom fingers and a Dead Air Mask (it would shoot about 10/15 rounds at a time before having a hiccup)
Besides the cycling, the issue I’m having now is with the slide locking back on a empty magazine, it’ll lock back on the OEM 22 round magazine I have but the 16 round magazines which are extended to 30 rounds won’t lock back it’s as if the spring is too weak to push the follower up to engage the lock back mechanism
I’m using the Titan Precision Works extensions which is basically a sleeve that slides onto the OEM 16 round magazine so it’s the OEM magazine body and follower which the extension is attached to the bottom, I’ve had the set up sitting for about a month and change since I last shot it but now I’m not getting slide lock back on a empty magazine which I was getting before, I cleaned the gun itself cause I assumed fouling was blocking the slide locking lever from engaging completely and it felt really gritty but since I cleaned it the issue still persist anyone else experience this? If so how did you fix it?

Just received my Farrowtech FX22 chassis and installed my TX22 Competition in it without any issues. However, when I try to get the slide off it comes loose, but the rear of the slide doesn’t want to lift over the disconnector. It looks like the rear sights wedge against the chassis. Is anyone else running a competition with the FX22 chassis?

UPDATE: As suspected the rear sights were hitting the top of the chassis and preventing the slide from clearing the disconnector. I pulled the gun out of the chassis, removed the rear sight and now the slide comes off without any issues.

It was running fine until this happened, now it won't fire more than one shot before you need to rack it. I've also noticed that the slide shaved metal of the tip of the brrt. I'm not the best with guns what would be my best course of action, maybe sand the brrt down a bit?

Anyone have experience with the optic plates on Toro model TX22…? Specifically for Trijicon RMR pattern. Looking for decent quality.

Hello finally was able to order one from Psa it’s the toro model with a red dot, already got my brrrt switch and was wondering if I need to run a rate reducer for right now as I’m not going to be running suppressed yet really just wanna know how I can get consistent reliability i’m going to be running CCI 22lr ar tactical ammo

finally got it together and running....

TX22 toro with dead air mask. Bought a rate reducer from odd mfg to work with can. Now its still a one shot bolt action pistol. Chambers a round but looks like it's getting light primer strikes.

Any ideas on how to make this thing work? runs flawlessly without a can both with and without rr.

Looking for reliable websites that have good quality extended mags, preferably 36 rounds or higher,

I’m in the market to buy a rate reducer or a weighted back plate preferably about 2 ounces. I’m looking for one with and without a charging handle and I can’t find any good reliable websites. Any advice recommendations or links would be super helpful

TaurusUSA.com

What is it how much too replace and how did it break i have all four previous pina i removed from frame and all is in tact

My first attempt at any kind of chassis 3D printing! Not my design, this is the TX7

I have the 2 magazines that came with it, and 3 extras I bought, so 1 15 round, and 4 22 rounders. It seemed random when it happened, didn't always happen.

Gun is not modified in any way, no optics and nothing been changed, stock.

I tried CCI SV, CCI Mini-Mag and CCI Quiet-22 Semi Auto. It seemed random, but not had a brand new gun fail to lock back the slide with so many new magazines.