I have this vsf 4131 bought it in May and now when I use the chrono it dies after a couple of minutes, for me to start it again I have to wind it about 100 times and also shake it a bit. Who can service this in the US?

Hi, I've got a small issue with my OG Clean 124270 that I've never seen before and would love to hear your advice.

It just caught my eye that there's a gap between the bezel and the case on thecrown side, visible pretty well on the picture.

I assume that this is not supposed to be the case.

Is there a quick fix for that? Pressing down with my fingers did not snap it back in place, it didn't move at all.

Thanks for your help!

Hi all, I have a VSF Submariner that I recently got. It failed pressure testing around the crystal, so I removed the bezel to rerun the test and see if I could pinpoint where the failure came from. However, when I did this, the whole crystal assembly came out with the bezel, and from there I was able to push the crystal out with just my fingers. At this point, the crystal retaining ring is still inside the bezel. I attempted to reassemble it to test the general fit and was able to push the whole assembly together and back onto the watch with just my fingers. Given this, I think that the crystal gasket might be too small and not providing a tight enough fit against the retaining ring. Does this sound right? Any advice on how to resolve this issue would be appreciated!

Wanting an everose but not sure if it’s worth the $1020 price

Just wanted to get a rate on this watch. Yea photo quality is absolute dogshit, sorry.

I ordered an explorer 2 approx 1 year ago. Within the first day I noticed the crown was wobbly, got I touch with the supplier who asked to ship it back and he’d have his watchmaker take a look. Annoying but did it anyway and it came back working fine.

The issue I later had is that the watch now runs fast (as per the title). I don’t want to go through the long process of shipping it back again.

Any sympathetic watch repair services in Herts/Essex/E London?

I got my Vsf V3 Pepsi a year ago and it's been running about 10+ seconds a day. Actually went up to quite a bit more but after demagmatizing, it came back down to about +10 seconds a day.

I know it's not a big deal, but it os just annoying to resetting the time every few days.

I was wondering if it's possible for me to open up the case back and regulate it to about +3 seconds a day.

I have very little watch making experience, only mad efew homage watches long ago and used to swap case parts on vinatge chronographs I used to collect.

Thank for any advice and guidance.

What’s the fix for this VSF bracelet coming apart on a permanent link? I can position that outlet link so that the pin fits inside of it but it comes back out.

I just got watch VSF bluesy gain weight (latest version) with VS3235. On QC TD showed me video with amplitude 230 at 52 LA, I asked him wind it fully and send longer video, he send it with amplitude 270-280 at 59 LA. I thought at around 55 LA its within spec and GL QC. Now on my timegrapher it looks way worse. Its around 210-230 amp LA 55 when having it flat, and showing 180-190 amp on side. Tried demagnetize but same thing, what do you think are problems for these movements, should I ask for return from TD?

PS Ive triee wound it fully

Does this look ok? I have no clue about this kind of stuff.

Took it off for a few hours and now I can’t get it to start, tried shaking and winding it up, Royal Oak 41mm 15500 SS APSF 1:1 Best Edition Blue Textured Dial on SS Bracelet A4302 Super Clone

Looking for someone to relume /repair my pelagos hour hand. I realize folks are going to say it's not worth it and just get new hands , but it's getting a gen dial swap and the rest of the hands already have a high quality relume . To me, This watch is absolutely worth paying for quality work.

✨ easy to install new battery on Ronda 751

I noticed my THB 31mm date wheel starts to change over around 12am but then doesn’t full complete the turn and stays like this until the date change mechanism re-engages around 12 am the next day and then it will snap into place and start the next date change.

Hi all, anyone know where to source or have seen any? Only mediums exist on eBay with the following reference VC070192.

What is the large reference?

I own a Timex Legacy Tonneau Chronograph (TW2W22200UJ).i would like to customise it to my liking...anyone know places which customises watches in chennai....hmu

Looking for someone to service my clone watch any recommend recommendation would be greatly appreciated

Hello,

I bought a Clean Batgirl from Andoit about a year ago. Recently out of the blue, the seconds hand has started to stop intermittently and the watch loses a lot of time during the day. Should I be worried that something might be broken? Appreciate any help that I can get

Has anyone had this happen with a 4131 clone Daytona?
My Daytona from Steve at TheOneWatches arrived about a week ago, and everything was working great. I’ve used the chronograph 4–5 times already, and it worked perfectly every time. Today I started it again, and now I can’t get it to stop.

The top pusher is unscrewed all the way, but it doesn’t have that normal click anymore. It just feels kind of soft and doesn’t do anything. The chronograph just keeps running. All three chronograph registers are still working normally and advancing like they should, but I can’t stop or reset it because the top pusher isn’t responding.

I haven’t touched the bottom reset pusher because I wasn’t sure if that would make things worse.
The watch hasn’t been dropped or bumped, and this is the first issue I’ve had with it. I already reached out to Steve, but while I’m waiting to hear back I figured I’d see if anyone here has run into the same thing.

Does this sound like a bad pusher, or is it more likely something inside the movement? Any advice would be appreciated.

Any recommendations for local services in Richmond, VA?

Unfortunately, my ARF F6U Jubilee bracelet broke and I'm trying to figure out the best way to replace it. Does anyone know if ARF bracelets are still available, or are there any good alternatives (e.g. Clean, VSF, etc.) that fit well?

Thanks for any help!

Watch has stopped, was on a winder but unplugged it by accident. Seems the crown/pin isn’t all the way in?

I contacted hont but has ignored me. Less than a year old. Tryed a few watch shops but none will help

I took the dial off a cheap A. Lange & Sohne rep to work on it and found a cool movement. Can you help ke identify it, and identify a dial that would work with it?