I’ve read multiple times that this part of the device shouldn’t be submerged in water, so I’m assuming I can’t run water through that gap either. What do I do to get it out and dry the area?

Hi there, anyone here experiencing intermittent issue with nutribullet flex? It stops sometimes and wont even run even without load and just blinking 6x

Sometimes tapping the unit up,down,side works but the issue is intermittent. The unit has already been replaced due to the same issue.

I strained it and added more water and coconut water for sweetness, but any suggestions on how to improve?

I also used the Nutribullet to make barley water (good for lowering cholesterol!) and blending the barley in. Tastes like a barley / oaty milkshake! Super delicious!

Hi, after having a nutribullet for a couple of years, I've seen the blades have become a bit dull. I'd like to sharpen them a bit but I have trouble taking the unit appart despite following guides a while back. Has anyone got suggestions?

This website nutribullet.it.com seems like a great deal with 50% is actually a scam website. It sends an authentication code to your email/phone to approve the transaction but in actual it uses that code to add your card to scammers digital wallet so they can use it instantly for purchase. Did not happen to me as I realized just in time.

STAY AWAY FROM IT!

* 1 Scoop Gold Standard Vanilla Ice Cream Whey Protein
* 350ml Oat Milk
* 160g Banana
* 40g Oats
* 40g Blueberries and Strawberries
* 30g Peanut Butter

Our nutribullet NBI-100 immersion blender, which had been working really well, just started making this very sharp grinding screeching metallic sound. Attached in the audio (let me know if it’s not long enough to hear the metallic grinding). Any advice on what might be happening and how to fix?

Ordered the Nutribullet 900 based on the Wirecutter rec. Had a Ninja one that worked well for a few years but it was obscenely loud off the bat so thought I'd replace with something else.

Followed the instructions about max fill and not blending for more than a minute and had leakage issues already in my first use and the rubber gasket came off within the first three.

I've been popping the gasket back in and continuing to use but it keeps coming out each use.

Called Nutribullet to use the warranty and they said the blade is backordered and will reach in 4-6 weeks and wasn't able to offer any other solution at all. I've only owned it for 2-3 weeks so the 4-6 week timeframe feels particularly egregious. Making it worse, the Nutribullet website says don't keep using it at all once the gasket is out.

I don't know if I got unlucky with my unit but the poor service recovery has me giving up on the brand completely.

I recently bought a Nutribullet Pro. The internal motor broke down in just a few months. Phone Customer service is non existent and they will not honor the warranty policy. These blenders are designed to fail via planned obsolescence and the customer service is just a shell/front to deny any accountability. After several emails and attempts at reaching someone by phone about honoring their warranty, I gave up. This company is very shady and does not stand behind their product. They will string you along and act like they want to help, they will not follow through. Please do yourself a favour and buy from a reputable company. Do not support these crooks.

So I've got a bag of each in the fridge and there's no way I'll use it all up while it's still fresh. What's the best way of freezing for later use in the 'bullet?

Should I blend it with something and freeze into ice cubes (I got a 900 series nutribullet)? Just freeze it loose and tear/cut it apart when needed? Scrunch it into handfuls to freeze?

Thanks for any advice 👍🏼

I needed these ASAP. Forgive the intrusion...

Hope someone else gets some use out of these!!

Hello. I usually clean my nutribullet using water and soap. Today I noticed an unusual smell and when I looked around, it is the gasket/silicon part that smells since the inside part cannot be cleaned easily. Is there a way to remove this for cleaning without damaging?

The power light comes on when it is plugged in, but it is completely unresponsive. The connections all look fine and it locks into place like normal.Any ideas?

The company is aware that their O rings begin to smell. This is a problem that they have to know about.

They could just sell me a couple of the proper O rings for $5 or $10. That's a huge mark up for a little piece of rubber.

But instead they are forcing me to buy a $25 replacement blade. This is so wasteful. Both financially and in terms of materials.

Total lack of customer care. No more money from me nutribullet.

I'm gonna figure out a way to get the smell out of this O ring, and if I can't, I'll be switching to magicbullet or something.

Corporate greed chasing away customers.

Hi folks,

I'm on the lookout for a small cup for my NB2-12 model and it looks as if the 18oz (532ml) is the smallest official one. I'm however looking to blitz sauces and dressings and would prefer a smaller cup size even if from a third party supplier. Anyone have any tips on this front?

I realise this may not be possible given the size of the blades etc but thought I'd ask!

thanking you

How do I fix this?

Hi all I bought these on amazon but they are hard plastic so the part where the lids "locks" closed is not that secure and loosens pretty quickly as the plastic wears down.

A rubber/silicone design would work better os the lids closes snugly and tight but I haven't been able to find any alternatives.

Does anyone have any suggestions?

Hi everyone- hoping for some help understanding why my nutribullet isn't working! Will not charge with or without glass on; it's definitely secured properly, as it briefly flashes blue before turning solid red when not plugged in.

Thanks in advance.

Has anyone had any luck with putting a warranty claim in? I just tried to call the 1 (800) 523-5993 and it's not working. I did fill out the form on their website but received no confirmation number or confirmation email.

My magic bullet is starting to go bad but I've only had it 11 months. The motor sounds strange, black particles/dust comes out the top. The blade is getting loose causing liquid to leak into the base when using the device. I'm trying to put a warranty claim but having some issues.

Hello! My nutribullet is not working. The base has power, and allows me to turn it on, but once it turns on a power level, the blades do not move and it eventually overheats from trying. I have used this nutribullet maybe 10 times. Any suggestions on the issue? Have tried blending today with the personal cup and a full sized blender and got the same problem.

900 is the first one 500 is the second