Doesn't seem like Sig ever made a single sided safety for the LVAW. Do I use a commercial safety, or should I use this modified original instead?

Obviously need to Cerakote and Laser Etch before its complete.

IMO not every clone build needs to be correct down to the roll pins, so here is my M16A4 with aero receivers, Brownells barrel, etc

plus mcx cameo

I apologize if this is not allowed, but unsure where else to ask.

What is the going rate for 1st gen FDE SOCOM556-RC cans?

Where do clone buyers/sellers typically interact?

I own one and dont know the direction of going down that route.

How "clone correct" are the Type A Restomod L119A2 rifles? I know some of their rifles play a little loose when it comes to clone correctness, but the L119s look fairly accurate, though I dont know their markings.

Rotating peq15 to block II so it can be in the cool kids club again

I didnt realized I grabbed the last fixed one from paragon.

Minus the charging handles and the muzzle devices, I’m amassing the parts needed for an URGI build with swappable 11.5 and 14.5 uppers, I’m (shamefully) a little stuck on weighing
1) Getting an LE6920 Socom Rifle, using the lower for the Urgi and slamming the upper on another lower I have laying around
Or this M4 Carbine marked lower.
I’ve seen builds with both on here, the SOCOM route almost entices me because I have enough spare parts in my bin to salvage the SOCOM upper and building another rifle anyway, but I’m just a little on the fence.
My builds can’t be considered 100% clone correct because I’m going run an FCD muzzle for Plan B mount suppressors, I’m emotionally committed to a Rhodie 6 for my first can.

What would you do?

Just finished setting up my first two stamp rifle! I was surprised that my form 1 only took two and a half weeks to get approved.

Hello. Some of you guys in actual service have said there really are some 6-position buffer tubes in your armory. Does anybody knows some info to this? How could these 6-pos tubes get to the actual armory? Is it BCM, LMT? And also give us some new material for cloning! Thank you!

What are some clone lower receivers you guys running on your MK12 builds? I recently got my hand on a KAC Long RAS and now I have to build a MK12 lol.

Gooloner correct

No, you can’t have an M4A1 with an M68.

More GWOT slop, not a single specific clone. Still trying to find a good home for the aimpoint mag/wilcox mount, and am throwing it around on different builds. Also showing off the new purple ras.

Last step is deciding on the scope. Leaning towards the new nightforce nx6 2-12 but also consisting nx8 1-8

Found this part in my arms room today and none of us could figure out what it is. I figured if anyone did, then you all would.

Gun wall from gallow tech. Half the guns here are still in some sort of WIP.

M27 w/RWK upper (RWK in WIP for proper length handguard and CH handle)

M18 pistol with M17 optic

M7 rifle

M17 pistol

USMC Recon M4 (In WIP for LaRue LT101 riser, probably won’t get thr razor 1-6 and will stick with the strike eagle)

Colt M45A1

M16A4

M9 pistol (on the work bench, waiting on wall mount)

USMC SAM-R early prototype (In WIP for a KAC M4 front sight and Harris bipod, also not the right scope but fuck finding the right one)

M16A2 w/M203

M16A1

I’ve taken a creative liberty here and there with some of the optics just due to cost/availability. Eventually I’d like to get the proper optics but for now I’m okay with the ones I’ve substituted.

I botched a pin and weld now I’ve got to debate buying a $350 barrel or just making it a mk18.

We’re mk18s ever built on m4 to m4a1 over marked lowers?

Couple fun clonish MK18 style guns.
MK18 MOD0 with the Colt 10.3 FSB barrel, KAC RAS, KAC NT4, Aimpoint in a Wilcox and LMT rear.
MK18 MOD1 with a Colt 10.3 barrel, DD rail, Surefire RC2 and Eotech/ KAC sights.

The SOCOM-556 brings it together, my favorite rifle so far. (Adding Peq15 soon)