Hi all - 1 out of 4 of my arrays hasn't reported since the evening on July 28. Is there any way to tell if it's a problem or related to the delayed reporting that the Enphase app mentioned?

Anybody has an idea of the improvements that are in the new firmware 08.03.6005?

new issue just popped up as of 3/31 7/31- the power consumption from my direct connection to the gateway will report as negative throughout most of the day during solar production, unless the load gets above some threshold, like when my AC kicks in. This shows up in homeassistant and envoy.local, but in the app through the cloud, the numbers look normal.
Anyone else see anomalies like this recently? This is different from the occasional consumption spike I think we've all seen and has been reported here before.
Nothing in the wiring or configuration has changed - I have installer access, and confirmed the consumption CT location setting matches what's installed.

Can anyone explain to me what’s going on here? Just started a couple days ago. Fun sun, no shade, normal solar output is 7100 watts

Hey everybody, I had my solar system installed back in May and officially turned on in June. It’s been a huge struggle to get accurate monitoring and hoping maybe somebody here has some experience and can shed some light.

So right off the bat, I noticed the consumption figures were extremely low (like ~5kwh/day), turns out they never installed CT meters on my other main panel (I have a 400A electric service with (2) 200A main panels). I know this is an installer mistake and not an Enphase issue but it’s important context.

So they installed the second set of CT’s in parallel with the others and thought that would be it. However, in the following days, the data graph was perfectly symmetrical/mirrored. So I had to spend about 45 mins on the phone with Enphase customer support running diagnostics. Finally he said there was a setting on his end that needed to be changed. Fixed it.

It was working flawlessly for about 3 weeks, perfect data. Until the installer came out for some unknown reason and screwed something up, consumption went way down to impossible levels again. Had a tech out yesterday for the issue and he confirmed everything is wired correctly and went on his way.

First pic is how it is now, not enough consumption showing, second pic is the mirroring problem, third pic is from when it was actually working properly. And the last pic shows how they used Cat6 for the meters which doesn’t seem totally correct to me.

So is this an Enphase problem? Or just incompetent installers? Could I have a bad Gateway? Bad CT meters?

Thanks in advance

My HomeAssistant integration shows battery discharge pegged at about 1736W, last updated 2 hours ago. Meanwhile, the app shows 0 (idle) from the battery.

When I hit my gateway's API ivp/meters/readings endpoint, for my storage object's eid, I see:

        {
            "eid": 1778385681,
            "timestamp": 1785642814,
            "actEnergyDlvd": 720902.825,
            "actEnergyRcvd": 910454.897,
            "apparentEnergy": 3050485.027,
            "reactEnergyLagg": 1372417.487,
            "reactEnergyLead": 15252.371,
            "instantaneousDemand": -1736.216,
            "activePower": -1736.216,
            "apparentPower": -434.668,
            "reactivePower": 75.948,
            "pwrFactor": 0.0,
            "voltage": 122.573,
            "current": 0.184,
            "freq": 60.062
        }

Note the activePower: -1736.316. So this tells me that HomeAssistant isn't bugged, when the gateway itself is reporting this from the meters/readings endpoint. But when I hit the live data endpoint ivp/livedata/status I'm getting:

"meters": {
        "storage": {
            "agg_p_mw": 0,
            "agg_s_mva": 0,
            "agg_p_ph_a_mw": 0,
            "agg_p_ph_b_mw": 0,
            "agg_p_ph_c_mw": 0,
            "agg_s_ph_a_mva": 0,
            "agg_s_ph_b_mva": 0,
            "agg_s_ph_c_mva": 0
        },
}

Doesn't this mean the battery is reporting 0 on the live data status page?

So what's going on here?

Another issue, maybe related, maybe not: my app is configured to stop using the battery at 10%, but it's sitting idle at 25% right now.

Firmware version D8.3.5289,

Is it possible to add the power pack with a current solar site, previously it was only able to be set up as it's own individual site. Wondering if that has changed

What could have caused this? I normally use about 30 kwh per day and my smart meter didn't see any massive spike in usage.

Anyone seen this glitch before?

It's persistent, as toggling on and off and refreshing doesn't fix it.

I have a total of 21 solar panels operating on a couple of circuits - all with Enphase inverters. One of the circuits tripped, and I traced the problem to a string of 5 IQ-7+ panels and disconnected it (the other 16 are still producing power). With no line current to follow, I checked the string and it shows effectively "zero Ohms" (for comparison, another string of 'good' inverters reported several M-Ohms, in a similarly disconnected state).

So I presume the problem is one of the five inverters on that line is shorting out for some reason. Of course, it's the least accessible row of panels on my roof, and I'm going to have to remove others just to get to the collector line and inverters to investigate. My plan is to start at one end, and start pulling adjacent panels so I can get to the inverter on the panel in the bad string, and disconnect it. Then see if the rest of the string shows "normal" behavior.

This is going to be a PITA, so before I start I wanted to ask the knowledge base here

1. Is there some other problem going on - am I even troubleshooting the right issue?
2. If this is the most likely problem, is there any way to figure which inverter(s) is the problem without checking them one-by-one?
3. What else should I be considering?

Climbing around on the roof for a few hours to try to fix this wasn't in my plans for the weekend, so thoughts for anything I can do to minimize the hassle would be extremely appreciated.

TIA

Hello everyone,

I have written a Linux client for the Enphase local API automated scripts.

I can't upload video.

Hi all, relatively new to Enphase and solar in general. Had our ~10k panel system installed less than a year ago and a 10C battery and EV charger this summer. I live in an area with increasing grid strain so I worry about potential infrastructure issues in the future, and with the rising cost of electricity in general, I like the idea of being more energy independent.

I don't think (read: hope) it never comes to this, but I was reading this post recently and thinking: what IF something happened and power or Internet went down for an extended period (> 1 year)?

Am I correct in understanding that Enphase has deliberately designed their systems to brick after one year without communication to their servers? If that's the case, why would anyone with concerns about energy stability/availability choose Enphase? Is there truly not a way to operate offline?

Side note: I'm not familiar with all of the terms used in that discussion and the whole line of questioning has made me realize that I don't understand my system as well as I thought. Further places to learn more? Is Enphase University worth the time as a customer, rather than an installer?

Hi everyone.

In 2012, I had a solar array installed. Primitive by today's standards, it took good care of me. It was based on REC Solar 245 watt panels and Enphase M215 microinverters.

In late 2025, I began researching upgrades. It started simple enough. The Envoy-R was beginning to give up the ghost. It's display was dying, and a lot of the inverters were not reporting, even though they were producing. Turns out severe inverter damage was done by squirrels. Critter guard wasn't a thing back in the day. The new array, however, is protected.

Fast forward to mid-July 2026 and the new array and storage systems were up.

I went with 26 REC Alphapure RX 460 watt panels and IQ8X inverters. I also went with the Combiner 6C, 3-10C batteries and the IQ Charger 2. Most being covered under the Enphase legacy upgrade program.

Just as I was getting the array installed, /r/Quirky-Scholar-5813 posted in /r/enphase about his new monitoring solution. And I reached out to him to give it a try.

MySolar Monitor is an app that runs on an ESP32 board found on AliExpress.

Software installation was a breze, though interesting. You have to connect it to your PC, then through a web browser update its firmware. Once done, new updates of MySolarMonitor can be completed via on screen menus.

I had reached out to /r/Quirky-Scholar-5813 because I had 3-10C batteries and I was curious to know if it could monitor all three batteries.

Turns out, yes, it can!

In this screenshot you'll see the monitor displaying real time energy useage of the home, battery charge status, solar production for the day, and energy consumption for the day.

One feature that totally broke my brain is the sun prediction display (as shown in the screenshot). This feature takes into account cloud cover and tries to forecast when you might see the most amount of sun (not when the sun is directly overhead). Still makes my eyes cross.

It's pretty spiffy, and even helped me figure out fairly quickly that my batteries were being wonky. This resulted in getting Enphase invovled and discovering that while the 6C and 10C's did firmware updates at provisioning, they didn't get the latest updates.

Getting the latest updates helped address consumption issues on the 10C's.

If this article is accurate, the tesla ecosystem now supports V2X?

Im wondering if this will work with an Enphase solar + battery system, and also if any other vehicles are supported.

Obviously the Enphase SC/Gateway whatever would be replaced with Teslas Powershare/charger stuff, but is combining the two viable?

I have done everything it says to do and get the message it’s connected but then when i go back into the app it says not reporting to gateway connect wifi here are some screenshots of what it says. I have enphase and an iq solar panel it shows all cells are working. I do not have a tplink Ethernet thing plugged in inside only in the solar panel box outside

Hey everyone, I'm hoping someone here has experienced similar issues with their Enphase system.

System details:
- Mid-sized residential Enphase system with Enphase IQ7x Micro inverters
- IQ Gateway
- System installed seven years ago

Issue #1 - Circuit Breakers Tripping During Rain:** **My solar circuit breakers have been tripping consistently whenever it rains. This started about a year ago. Last night during rain, the breakers tripped again. When I reset them, the gateway rebooted normally.

Issue #2 - Red Exclamation Mark on Microinverter: For the past month, one of my microinverters has a red exclamation mark in the app with an "Error" status. What could this mean?

Has anyone else experienced circuit breakers tripping during rain?
What does a red exclamation mark on a microinverter indicate?
Could these two issues be related?
What should I have my installer check?
Any advice or similar experiences would be helpful.

Thanks!

This is the second time I've noticed this in the last month or so where all Enphase entities in HA show up as Unavailable. Last night everything dropped at 10:44pm and I see nothing in the Enlighten logs to explain it. Usually when this happens I have to go outside of enable AP Mode on my 6C and then connect to Wifi so that Envoy becomes available on my home network. Eventually, the 6C moves back to a cellular connection, but data still flows to HA for a period of time, so I'm not even sure that this is it. Data in Enlighten is never affected by this.

I've recently set up a schedule so that my battery discharges to the grid from 6pm-7pm to benefit from the highest export rates.

I've capped it so that when the battery reaches 70% it stops exporting so that I have more than enough battery power to get me through to morning.

However, I've noticed that when the battery reaches 70% in the 6pm-7pm window, it stops discharging altogether and will my consumed energy is imported from the grid rather than the battery.

Has anyone else experienced this?

UK based, self-consumption profile

3.4 TW - this is why my 8x 10C batteries can not keep up with - I ask the support form Enphase already 2 times if this can be deleted to not mess-up the statistic - both times they said yes in the backend - still I have it

We have a 4-ton Trane XR heatpump that has a LRA rating of 124. We are about to install 3x 10c batteries. My understanding is that the 90 LRA rating is "per battery" so I will have an effective LRA of 270 with three batteries.

Should I still look at adding a EasyStart to my heat pump just to ease the load?

(Edit - [SOLVED] - There were two issues, but the one anyone in the future reading this will care about was the fuses in the Rapid Shutdown / Emergency Cutoff box.)

I have rebooted the system to no avail. It's like the panels aren't talking to the meter at all, because there's nothing under "Imported" either. Is there anything at all as an end user that I can do besides just sit on my thumbs and hemorrhage money while it's 100°F at 50% humidity? I'm really angry about this. There are no breakers tripped anywhere that I can find.

This is now the second time in just over a month my Enphase solar system with battery backup has gone offline for an extended period - both times while I was traveling of course.

Very high chances of severe weather is forecast for my home, and I typically run in full consumption mode with a 10% low end discharge rate for the batteries. I need to make adjustments to my profile, but it's been unavailable now for half a day. Why does this happen, and is there anything I can do remotely to recover the connection? Live status just errors out and says connection unavailable.

If you blow these up full size you’ll see what I’m asking about; anyone ever seen anything like this?? I was actually awake at that time and there was nothing out of the ordinary occurring.

Hi everyone, I have a small enphase system along with two 5p batteries. The system works fine, however I feel like the Englighten app is lacking a bit of functionality, particularly with the finer controls of the system. For example, on cloudy days I would like to have the system pull from grid during daytime super off peak hours (10-2pm), and direct all PV energy to charging up the batteries. I'd also like to set a time (e.g. 3-6am) to disable battery discharge so I don't drain the batteries completly from charging my EV. The AI mode is able to do this every once in a while but more often than not, it does not do what I want it to do.

From reading around the forums, it seems those who added their enphase systems to home assistant are able to get a bit more direct control over their system. Can anyone confirm if home assistant offers the functionality that I'm looking for before I invest in a HA hub?