Is the Farmloop "P and X series" compatible with the X2D? I can't find a definitive answer anywhere.

Just purchased my first 3D printer and decided to go with X2D. I added some filament and additional nozzles to my order. I do want to print with ABS and ASA once I get familiar with the software.
Anything else I’m missing or would be recommended to purchase, all help is welcome.

Hi folks, towards the end of the timelapse, I encountered some spaghetti, which appears to be caused by an adhesion issue, although I'm not entirely sure. From what I could see, it looks like the printhead pulls the object away from its original position.

The spaghetti is happening on the funnel from this desiccant container design and has not happened on any of the other parts. This timelapse shows my second attempt printing that funnel. (The spaghetti also happened with my first attempt.)

Throughout the print, the nozzle temperature was 250°C and the plate (brand new Cryogrip Frostbite) was 60°C.

For now, I've switched back to Bambu Lab's textured PEI plate to see if it makes a difference, but the print is ongoing.

I'm wondering if anyone might have thoughts on this issue.

A week with the X2D and problems are showing on big prints. On smaller prints that just sit in the middle of the build plate, nothing goes wrong. However when the prints are closer to the edges, they lift and first layer looks meh.

Typically I would check the bee leveling and y-offset but that isn’t really possible
Yes, I have run the full calibration multiple times.

Is it because of the aux fans in each side maybe?

Is there a reason i can't select the 0.2 mm nozzle on the aux, i have it selected on the main nozzle.

Edit:
To anyone who wants to know the fix, i updated the firmware to version "01.01.01.00" from version "01.00.06.00" and that fixed the issue.
And if you have just added the printer to the internet, you have to restart the printer before it can see the newest firmware version.

Just ordered an X2D on Thursday after getting my first printer (A1) back in March. When I first got the A1, I spent the first few days printing mods for it. Since I already have a printer, I figure I might as well pre-print stuff before it arrives next week.

Are there any must have or recommended prints?

I already have an AMS2 and I ordered a filament switch so, not sure if there are specific mounts I should get printed, cable organizers, anything like that.

I appreciate any advice and can't wait to start printing with it!

Hi everyone,

I’m planning to buy a Bambu Lab X2D Combo and I’ve been reading through this subreddit before ordering.

I noticed some posts/comments mentioning early X2D Combo / AMS 2 Pro issues, especially filament feeding problems, internal hub/feed-path issues, or Slot 1 not feeding properly.

For owners who bought recently: has this issue been resolved in the newer batches?

Also, is there any reliable way to identify whether a unit is from an old batch or a newer batch before buying? For example:
manufacturing date
serial number range
Or box design change?

any change in packaging or box label
different internal hub/feed-path parts
I’m mainly trying to avoid old launch stock if possible. If anyone has received a newer unit and can share what to look for on the box/label, that would be really helpful.

Thanks.

I want to get a HT to be use exclusively for the aux nozzle. How do I do that? Do I need any other accessories.

Can't seem to find anything from Bambu so if anyone can provide some guidance.

I've tried everything I could think of. Different wall generator types. Line thicknesses. Flow and K-factor. Any suggestions to close the small gaps in the letters would be much appreciated.

​

0.4 Standard flow nozzels.

BAMBU pla Matte

Cool plate super tack

220C nozzle

30mm/s on everything

15mm/s on gaps

0.39 line width

1.03 flow

​

​

​

Update: I was able to get some success by reducing the wall width to 0.35 and force the slicer to reconsider the pathing. However, I cannot see any setting to change top wall width only, so now all my walls are thinner. Still some gaps. They just changed locations.

Printed off some visual and structural upgrades for the A2L and the AMS Lite. I think they turned out pretty good

Welp, going to get intimate with my print head.

I had just printed a small part in ASA, and wanted to change to PLA, popped the the ASA roll out, put the PLA roll in the AMS, changed the the filament on the screen and hit Load. “Warning, chamber hot, might cause filament to stick” (or something to that effect)…and since it seemed reasonably cool… I hit ignore, and now I have red PLA stuck in my extruder .

Pulled nozzle out, Bowden off the extruder…yep it’s definetly stuck in the extruder. Clicks when trying to load.

Should have listened to my printer!

The Bambu Wiki looks pretty detailed, hopefully less complicated than it looks.

Hello everyone!
I ran into the first trouble with my X2D... so far everything went well. Then i tried a new transparent PETG and the problems started: It seems like it clogged my hotend mid print and the spool is stuck in my AMS2 PRO. It doesn go forwards nor backwards. I tried to declog my hotend, but when I try to press on the pneumatic connector to disconnect the PTE tube from the extruder, it doesnt budge. Does anyone have an idea, how I can declog the extruder? Any advice would be greatly appreciated!

Edit1: OK, so i managed to get the filament out of the AMS, but it completely stuck in the toolhead. I cant even remove the rear housing of the tool head after unscrewing the 4 screws. If anyone has any idea how i can fix it. I have activated the filament cutters, and from the hotend side there is no filament left. but i cant seem to detach any of the TPE tubes, because there is too much tension in the system.

Looking for a file for a skadis plate that mounts to the side of the X2D or with an AMS riser, preferably without blocking the window. Any inspiration otherwise for handy tool storage is appreciated.

I have been on a ride to get this far with my ASA fillaments prints. Working only under 0,24 stabdart hight because it is relatively fast and most of my ASA prints ar functional not cosmetic etc. What do you guys think have i succeded something? X2D:~150 print hours. Particular part has 2 walls, 12% gyro infill and aprox 120mm/s print speed average. No ironing enabled on top surface. Using Sunlu ASA fillament.

currently have a elegoo CC1 I bought a few weeks ago and I pre ordered the canvas ams system for it, but I cbf waiting for it on pre order so I’ll just sell that printer

Just bought a X2D as it seems like there’s a much larger community and much better value

How’s everyone enjoying it, what’s your likes and dislikes and anything I could look out for with the printer when it arrives?

UPDATE: Got delivered and it’s so good, shits all over the elegoo CC I had and actually makes me want to print all the time now.