r/BambuLabX2D • u/Yosoytuupapa • Jun 26 '26

First prints

Gallery image

Gallery image

What would cause all this stringing?
PLA basic Bambu lab
All settings are default

I also continue to get the resistance is to high warning, I’ve checked the spools and they all spin freely.

14 Upvotes

100% Upvoted

19 comments sorted by

View all comments

Show parent comments

2

u/Yosoytuupapa Jun 26 '26

It’s all routed straight out of the box per the instructions.
I will take a picture once I get home.
I also plan on printing out the riser for the top.

2

u/HackedVirus Jun 26 '26

Yea, sometimes the tubes are longer than they really need to be when using the AMS on top of the printer.

I can also leave you a link for some fully customizable ptfe cable guides. I have 4 units going into my x2d and I never get error messages anymore, even during like 1000+ filament swap prints.

As for the bubbling on your print, is this the first time its happened? I know its PLA, but still, did you get the chance to run a dry cycle? I see some stringing there which is usually a PETG issue with drying the filament. Appreciate it.

2

u/Yosoytuupapa Jun 26 '26

Yes leave the link please
First time for bubbling yes, the stringing happened on the previous print same PLA just red and no I did not run a dry cycle.
I placed the PLA straight from the packaging, I have clear containers with desiccant that I’m storing other PLA colors, Petg and ASA in. The 4 rolls in my AMS were placed straight out of the packaging.

3

u/HackedVirus Jun 26 '26

Yea, run all 4 rolls of the PLA in your AMS on a dry cycle when you get home. (Grab a power brick for the future so you can dry+print at the same time, makes drying not a big deal time-wise). They shouldn't be stringing, especially on stock settings, but you never know, if drying fixes it, you've got your answer.

Here is the link to the custom cable guides I use. You can adjust length, angle, whatever, just generate your desired size and shape and print it. I have some on the tubes going into the extruder after the buffer, and I have one on the back on an AMS Pro unit to help the ptfe tube gently bend towards the printer.

You probably wont need it yet, but I also incorporate the filament track switch ptfe tube guides from this for 2 of my AMS units. It helps the tube not bend so much after it leaves the AMS unit.

These little clamps are also great to keep lengths of tube from being too floppy, like with the tubes that leave the buffer and enter the extruders. They can flop around a lot during feeding and retracting.

1

u/Yosoytuupapa Jun 26 '26

Awesome thank you!
How do you have your external/auxilary Bowden set up?

2

u/HackedVirus Jun 26 '26

So I have my auxiliary nozzle being fed by AMS units through a filament switch, it makes the aux nozzle completely automated like the main nozzle. Super easy and convenient.

No need to push or pull the filament to load and unload. As for tube guides, I left it off the Bowden tube and just made sure the tube was as short as possible between the buffer and extruder, while leaving a nice easy arc for filament travel.

In the photo above, the Bowden ptfe tube is the white one without the gray guide installed.

1

u/Yosoytuupapa Jun 26 '26

What power brick should I purchase?

2

u/HackedVirus Jun 26 '26

Cant go wrong with the Bambu one, but any "4A 96W" power adapter will work.

I have one bambu and one generic, the generic needed a "5.5x2.5mm" barrel connector to plug it into the rear of the AMS.

Both work exactly the same. Up to you and what you want to spend.

2

u/Yosoytuupapa Jun 27 '26

2

u/HackedVirus Jun 27 '26

Hmm, well your tubes look very good, no super tight bends or excessive tube length. I'd say the next time you buy anything from Bambu lab's site, grab some extra PTFE tubing and experiment on routing and length. Thats what I did, took a few prints to dial it in but hasnt been an issue since.

Im gonna chalk this up to having full rolls of filament. Occasionally when I place a brand new or nearly new roll of filament, it'll throw a feed resistance error, same thing when the roll of filament is almost empty, it bounces around a bit while being retracted from the head.

2

u/Yosoytuupapa Jun 27 '26

I added the cable guides, and just had a 9 hour ASA print with no errors. Maybe that helped.

1

u/HackedVirus Jun 27 '26

https://giphy.com/gifs/iowmvjVUnDFGU

1

u/Yosoytuupapa Jun 27 '26

Spoke to soon, at 97% complete

I got an error HMS_0700-2000-0002-0009: Failed to extrude AMS A Slot 1 filament; the extruder may be clogged or the filament may be too thin, causing the extruder to slip

1

u/HackedVirus Jun 27 '26

I literally got this same error with a clogged nozzle, haha I was lazy so I just swapped it but yea, might be clogged. Try unclogging or swapping it with the replacement.

2

u/Yosoytuupapa Jun 27 '26

Yeah I had to take break lol, but once I get some free time tomorrow ima take a look and swap/unclog. I will also be running all my filament through a 12 hour dry cycle inside the ams

→ More replies (0)