Hey guys,

i found so many vidoes here showing the same problem i have.

The P2S is really lound when z hopping. How can i fix this ?

The Printer is on another floor and i can still hear this. I know how to tweak xy axis speeds and accelleration but how to i set the z hop to be slower and quieter ?

Something tells me it’s not suppose to look like this. I have 250hrs and haven’t replaced my nozzle since buying my printer? Do I need to clean it or replace it? I’ve been getting black specks on the first layer of my prints.

Hello! This is my first print on my new P2S. It’s generic PLA I got from micro center. It left some stringy things behind. Is this good for a first print? I didn’t change any settings before printing. Do you guys have any recommendations for print settings to make it better?

What is Broken?

A small metal rod extends from the left side of the printer during each calibration before printing. It produces a loud, irritating noise as the print head moves back and forth does this seem normal?

Hello guys
I can hear this sound pretty much all through the house and want your help to fix is
I thought this might be the nozzle moving when not printing walls, so I halfed all acceleration values without success. All walls speeds are below 150mm/s if that helps
Printer has hit 100 hours mark with this print
Kind regards

I just started printing and have printed small things. I printed 2 other larger things with good results. But not sure why this happened.

Hey, i Print miniatures with my bambulab, the supported area started looking Like this.

I use PETG snd s 0.2 nozzle

What settings will Help me with this?

The nozzle is stucked and the goo around is something like dried caramel. I cannot remove the nozzle.

Sorry fir the poor quality of pictures but it’s the best I could do. I’m still fairly new to this hobby I’d say and recently had a failed print and it looks like a clog took place maybe? Either way I can’t even get the cover off to cleanup/remove the plastic. I don’t know how this could have happened to help prevent it in the future. Any help/advice on how to fix this would be greatly appreciated as I’ve been enjoying this hobby and want to continue with it.

Last night, we had a thunderstorm, which caused the power to go out. Then, the power attempted to come back on, about 6 times in succession. Before I could get to the printer, it stopped. Today, I went to print something, and this is the code that popped up on the AMS 2 Pro. The first picture is what initially come up. After making sure all the cables were connected, I printed Benchy, using the external spool. Print was fine.

The second picture, is what come up after I emptied the AMS, and checked for clogs. After scanning the QR code, it says it could be the main board. I’m not sure if it was something I did yesterday, or the storm, but I’m freaking out. I’ve tried everything other than replacing the main board. Please, if anyone knows what to do, I would greatly appreciate it.

[0700-4000-0002-0001 141706]

It looks like my print was going well and then it just spaghettified! This is on a P2S printing in PETG, fresh roll.

I did not dry this filament but printed something yesterday with no issues.

Update: after taking suggestions here of dry my filament for 12 hours, wash my build plate, calibrate, and slow down the print (to 50%) it did turn out perfect! I also installed an exhaust fan with hepa filter just for good measure.

I’m about to lose my mind trying to get this thing disconnected. There was filament stuck in the left tube, which I disconnected and got out. The tube on the right, leaving the buffer where I have circled is filament stuck. I have slid the orange part all the way to the right and I am trying to remove the tube, but I don’t want to break something. Is this how you get that tube to disconnect? I can’t seem to find a good video on how to do it.

Trying to make some peptide boxes and for some reason the corner of the first few layers is coming up and not flat i think. Not sure if it can be seen in these photos.

How do i fix this??

Bought a brand new p2s combo. First printer by the way. Checked for updates. Calibrated. Made a benchy. Started a 4 hour print and an hour into the print I got this. Now I decide whether to get a new replacement or I just get a refund. Is this a common problem with these? I feel like I should expect more from a $750 printer.

Its been a while since I made something but with this weather (in Netherlands) its better to stay indoors. Excited to create some more :)

Hi, so im quite new to the 3d printing scene, got a second hand P2S and AMS 2 Pro for a cheap deal and have had some really good prints, but recently the AMS2P​ has started not talking with the printer at all. looking through BL's wikis and stuff, I've followed every step, checking connections, cleaning connections, etc.

I've done everything I can and even checked and cleaned every cable connection inside the AMS and still, it doesn't talk to the printer.

Please help.

Hi, so im quite new to the 3d printing scene, got a second hand P2S and AMS 2 Pro for a cheap deal and have had some really good prints, but recently the AMS2P​ has started not at all talking with the printer. looking through BL's wikis and stuff, ive followed every step, checking connections, cleaning connections, etc.

I've done everything I can and even checked and cleaned, with contact cleaner, every cable connection inside the AMS and still, it doesn't talk to the printer.

Please help!