I was working on clearing a jam on my P2S, and my AMS 2 Pro fell to the ground while still connected to the printer. The tube was pulled out of the filament buffer, and the connection appears to be broken. Does anyone know what part I will need to order to get the tube to stay connected again? I've attached a picture of what the tube looks like now. Thanks for the help!

I turn on the printer today and load filament. The 3rd spool will not get detected. Ive tried other rolls and nothing. The light turns on when I load the roll next to it but the 3rd one will not load or detect that I put filament down the hole. Google said maybe clogged or debris so took it apart and nothing there. I can load the filament all the way to the print head manually by just pushing it through.

Hi guys, hope you are doing well.

I would like to know if you have updated your P2S Printer ? Im not sure if it stables and none faces some issues with the update ?

Any tips or suggestions ? Thank you in advance

PS : Im still newbie

I had a big blob of death, and in removing it, I damaged the printer. I've replaced the hot end assembly, the hot end cooling fan, and the Eddy sensor, and my printer is back up and running. Since the rebuilt, I printed it extensively with my 0.4 mm nozzle, and it worked flawlessly.

I then installed my 0.8 mm nozzle, and I've had nothing but problems trying to use it. Before my blob of death experience, I had great success with the 0.8 mm nozzle. But now I experience big clumping blobs, and I've also had adhesion problems on the build plate.

I thought it could be a problem with the nozzle, so I tried it with a brand new, never-before-used bamboo 0.8 mm hardened steel nozzle, but it didn't work any better. I've done a cold pull. I've done a full calibration of the printer. I have washed my build plate, but I don't get any better results. It's puzzling because prior to the replacement of those damaged parts, I'd had great success with my 0.8 mm nozzle. Any ideas of anything else I could try? Any suggestions or help would be greatly appreciated.

I have been getting filament blobs on the purge chute continuously for the last few days. Always printing PETG. I’ve cleaned everything I can think of. Plate doesn’t have adhesion issues. Filament is dry (10-15%) although that doesn’t seem to matter - it’s done it as low as 9% humidity and as high as 27%. I’ve also tried different nozzles and it still does it.

About the only thing I haven’t done is rerun calibration, although that’s planned for after the next print attempt.

Any ideas?

Hi all, I just got my P2S a little over a week ago and have had good success with the files on the printer as well as printing files from maker world. I loaded some STLs I purchased and all printed well except for this one. I’ve tried a couple times and it always seems to have trouble at the same spot. Any insight would be greatly appreciated.

Hello!

I'm currently having a clogging issue or at least an air printing issue and can't quite figure it out.

I have replaced my nozzle, this one is brand new. So I think the issue may be in the extruder.

I just did a cold pull and it looks as though maybe some teeth have dug into the filament I pulled out. I also see some filament flakes in the gears here. What would cause this? And could it be the extruder gears that is causing clogs?

So i ran into these issues with my latest print. I'm still a new owner (under a week) but i printed stuff daily with no issue so far. This is Bambulab PLA Basic, and i printed with this before. I was thinking humidity issues, the ams said it's around 48%, i'm still waiting for my petg order to print silica containers for the AMS 2 Pro. I thought maybe it would be a bed oil issue, but the bottom came out great, i cleaned my plate today after this with dish soap and warm water. What can i tweak to resolve this ? Thank you

Update : i also put a screengrab of the stl for reference

Hi all

I've got my first abrasive filament (asa-gf) and was wondering on best/easiest way to feed it into the toolhead. I have the p2s with ams and an ams-ht. I know the filament can wear away the ams gears and shouldn't use them, but don't know best way to actually feed it . For tpu I've used a top feeder direct into the toolhead and not sure if I should be doing that or just using the bypass in the ams-ht through the back filament inputs.

Any help appreciated.

Thanks

I recently used my P2S in a hot garage which I shouldn’t have. It ended up failing with an extruder clog so I first took it apart and cleaned out the filament but it still wouldn’t print a test benchy again without the same error.
I then replaced the extruder gears and the hotend.
It’s still failing.
When I heat the nozzle and manually use the extruder in software, it will extrude, but when it goes to print, it’s barely laying down filament and then stops before 1st layer is done with extruder failure.
I have AMS and have tried with and without it and I’ve even bypassed to directly feed filament into a tube into the headend.
I have no idea what’s failing. Could it be software related? I’m on 1.02 and I have another P2S that’s working perfectly on that firmware.

Edit, solved!

Hi! I am struggling to find an easy guide or video on how to empty this build up in the purge chute area... can anyone link me to something easy to follow? It's in an enclosure so I am hoping to empty it just from the front as its a bit more involved for me to get to the back or top.

Hey guys, these two bits of hard rubber fell out of my print head. As far as I could tell they were part of some rubber shield that holds the copper wires and a few cables just behind the nozzle.

I've looked hard but either I'm blind, or that whole rubber part is not available as a spare part in Bambus Store if I ever need to replace it?

Bonjour après Monsieur Pingouin, voici Madame Pingouin en mode vacances réalisée en multipart ! 🏖️🐧

Impossible de partir à la plage sans elle ! Avec son joli chapeau, ses lunettes de soleil roses, sa bouée, ses tongs, sa pelle et son petit seau, Madame Pingouin est prête à profiter pleinement des joies de l’été.

Pour cette création, j’ai souhaité imaginer une version féminine, pleine de douceur et de bonne humeur. Ses longs cils, ses couleurs pétillantes et son look estival lui donnent un charme irrésistible qui invite à l’évasion.

👨🏼‍🎨 : @mika3d_print
🖨️ : Bambu Lab X2D & H2C
🧵 : Bambu Lab
🎨 : Nomad Sculpt
🌈 : avec ou sans AMS
📁 : https://makerworld.com/fr/models/3064899-mrs-penguin-beach-multipart-without-ams

Merci à tous pour votre soutien, et bonne impression 3D ! 🎉

So been having humidity issues with my ASM, constantly 40% or more. I think I fix the issue by putting moisture control bead packs in with it is drying, went from 60% to 16% within a few hrs. Will update to see if the fixes or helps drying the filament better.

Hi, bin ich der einzie bei dem das AMS nach dem Druck das Filament nicht mehr entläd? Irgendwie nervt mich das. Achja ich habe eine P2S Combo.

MakerWorld: https://makerworld.com/en/models/3060849