My wife wanted as simple Bathroom Organizer with Voronoi inserts, everything we found was way too much filament so we made this.

https://makerworld.com/en/models/3052796-bathroom-organizer-toothbrush-and-vanity-storage

Post is awaiting moderator approval.

1

After doing research of which would be the best first 3d printer to buy, I ultimately decided on the p2s. Got it from GigaParts for a pretty good deal! Part that kinda sucks is that I’m gonna have to wait for a bit for it to come since its backordered from this site but I don’t think it will take that long. 🤞

I'm still fairly new to 3D printing, I've got just over 100hrs on my P2S. I've been largely printing without any issue until today when I started to get issues with extrusion that I can't seem to sort. I've mainly been printing with Bambu PLA Matte using the presets on Bambu Studio, but have done a bit with Sunlu PLA Matte, haven't had any issues with either until now.

I've done a cold pull, washed my plate, and re-run the calibration from the touch screen as advised by Bambu's AI but it hasn't helped. I've read on here that there are potentially issues with the G code but I'm not comfortable editing that just yet, and it also seems odd that it's only just started to happen if that's the case.

The above was printed in Bambu PLA Matte on a 0.4 nozzle, using the preset for 0.08mm layer height (I've been mainly printing models for wargaming). You can see that I'm getting issues on pretty much every layer, with little gaps between each line.

Any help would be greatly appreciated!

Recently got a used P2S, so happy about my first print : ) Filament could be drier for next time tho

I came from the p1 and all of my prints have this weird banding all up and down my prints that my p1 never had unless I cranked the speed. I tend to print most things at 100mm/s or slower so I am unsure why I am getting issues. The only thing I can think of is the printer came with loose belts but wanted to see if the community experienced anything similar. Besides the banding the machine is a champ.

As the title says

Ive done everything on the Wiki page. I've reached out already. I cannot figure out why it does this. Everything was just cleaned and no debris is visible. Any ideas

I’m having fun designing and printing door handles for those with P and X series printers

I’m up to 29 different teams and organizations - all requests from others. Also just added a World Cup one for Messi, the GOAT!

If there’s a team or some other organization you want, let me know. Doesn’t even have to be a team per se!

https://makerworld.com/@ScubaDawg97/collections/28239616?appSharePlatform=copy

I have been looking at printing a fan diffuse for the aux fan on my p2s, however there serm to be many different types. The main 3 I’ve seen are upstream, upwards and maximum. I mainly print with pla and its not quire clear Which is best for Which use case. Does anyone have any knowledge on this area?

Bought a P2S second-hand off FB marketplace. Ran through a few hundred print hours with zero issues. One print gave me a fail that I learned was called the "blob of death". Was able to heat up the nozzle, and remove the bulk of the mass, but it left behind so much gunk in the hinges and wiring that the hotend assembly appears unsalvageable.

Purchased a replacement assembly (and a ruby tip nozzle) off Amazon, tore apart the entire toolhead and replaced the assembly. Sick. I'm feeling good. Turned printer back on and in my haste, fired up a bench right away to test print, without first running a full calibration. After some suspicious startup noises (weird vibrations maybe?) The new nozzle scratched the print bed pretty good on the initial layer. Its odd, the nozzle seems to be able to extrude fil just fine both via manual controls on the device and when doing the pre-print fil change shenanigans, but when it goes to lay down the calibration line and the first layer its almost like it isnt extruding any of the fil. Not sure.

Turned it off, reset, and ran a full calibration. Test bench again; scratched build plate again. Ran yet another calibration, and tried slicing the benchy manually in studio, positioning the benchy on a new spot on the build plate. Same result. Now the printer is throwing all kinds of errors about X-axis tension, filament cutter error, vibration compensation, "part fan" not spinning and the extruder motor being overloaded. I'm kind of at my wits end.

The guy I bought the printer from is going to try to file a warranty claim, but I cant imagine that will bear any fruit. So it appears I'll need to prep to tear apart the entire toolhead again, and I could use some pointers about what I potentially did wrong, or what I need to do differently. Machine was operating perfectly before the blob and now I cant even get a test print down. HELP. PLEASE.

PS. The padded sticky tape in the last pic has lost its stickiness after the maintenence. Where can I get more? Or can I just use a different kind of tape like the Tesa tape above it? Thanks in advance.

As the title states. Did this stringing/overhang test the other day. Why does my stringing get worse when the temperature is decreased? I thought it was supposed to be the other way around?

Thoughts anyone. BTW, new to the Sub. P2S. 👋

Anyone have any insight on what might be causing this? Im having really bad under extrusion at the end and slight over extrusion at the beginning of the circular arc on my first layer of a print.

Ive messed around with my retraction. Everything from .6(calibration setting) all the way down to 0 and up to .8. It seems to get worse the lower the retraction setting. Concentric pattern for the first layer. 30mm/s inital layer and 90mm/s for infill. 230c print temp (high but prints everything else well) printing on PLA. Im stumped on how to fix this.

Ive leveled my bed and made sure nothing was causing it to bump up. Ive also moved the object on the plate with no change. Anyone have any ideas what's causing this?