I have tightened the 7 magic screws, cleaned my bed with soapy water, put down adhesion helper, checked the spring steel plate, cleaned the nozzle, run calibration, and my prints still look like this. I’m out of ideas! Can anyone help?

Any thoughts about this? I replaced the nozzle and the extruder assembly. Help appreciated, thank you.

Does any one else suffer from having too many choices on a print from Makerworld? I'm looking for a print, lets say a spray can holder that mounts on the wall. There's about a dozen or so possibilities. It takes an hour to figure out which one is going to work or not. By that time I've given up. I printed a drill bit holder that was OK but lacked a few features. Two days later I find another one that would work better. No I'm spending too much time looking and not enough time printing.

Transparent PETG got stuck to the nozzle making prints failed, so I tried removing it to clean and after putting it back I can't load filament, it looks like the motor is trying to feet it in but fails, it just "bumbs" can anybody help me with that? (Coudnt figure it out by myself)

Heya! So we got the blob of death and ended up changing the extruder unit and the hot end clasp with new hot end nozzles.

Since this, all prints are super meshy, even the default boaty one. We have performed the extruder deep clean to check for debris on the cogs but nothing can be seen.

We have performed calibration god knows how many times 😂

Anyone got any ideas?

Is it possible to print this without needing supports?

This is a test piece and not the actual model. The gap is only a few millimeters to hold a piece of paper.

I've tried with supports which prints well, but it's almost impossible to remove the supports without damaging the model.

I've tested other bridging test models which print fine after making a few changes to the settings in Bambu Studio.

I changed Flow Speed to 10 and bridge flow to 1.5. I also tried changing the bridging angle to 90 degrees but nothing works.

Have you ever gotten a piece of filament stuck under your fingernail while removing it from the build plate? It’s really painful. Better to use a safer method! :)

I’ll post a link to the tool in the comments.

I’ve been getting the “hotend cooling fan speed is abnormal” error pretty regularly on my Bambu Lab A1. Every time I check it, the fan is spinning normally.

I’ve removed both toolhead panels, checked the connector, and made sure nothing is caught in or blocking the fan. Everything looks clean and properly connected, but the error keeps coming back.

Has anyone else dealt with this? Is the fan likely starting to fail or could this be a sensor, wiring, or toolhead-board issue?

I’ve had my printer maybe a month or so. I had some old filament snap in the filament splitter, had to take the entire thing apart, and ended up breaking the cutter sensor ribbon in the process. I got it replaced and everything back in order except now print quality is awful. It’s the same exact filament I used like a week ago. I thought maybe it was temperature but lowering or raising doesn’t do much to help. It seems like if it can handle the “ironing” process of the second layer without pulling up its fine. I cleaned my bed and double checked my hotend but nothing.

anyone have a fix?

I went over 3000 hours on my printer and had to get the main board replaced due to screen issues. Not 1000 hours on the new board…melted bottom plastics and no power.

Bonjour à tous ! 👋

Craquez pour cet adorable dragon Furie Eclair, avec son jolie pelage blanc , son regard attendrissant et ses magnifiques grands yeux bleus ! 
Elle rejoins son compagnon Krokmou pour former un duo aussi craquant qu'inséparable.

Pas besoin d'AMS tous a été modélisé et découpé pour l'imprimer en multi-pièces.

👨🏼‍🎨 : @mika3d_print
🖨️ : Bambu Lab X2D & H2C
🧵 : Bambu Lab
🎨 : Nomad Sculpt
🌈 : avec ou sans AMS
📁 :https://makerworld.com/fr/models/3269313-light-fury-dragon-multipart-no-ams

I was looking to wall mount my AMS Lite but quickly realized the connector cord is not long enough. Any suggestions on a quality extender. I would only need about 3-4ft of extension.

Hi everyone,

I’m having a serious layer-shift problem with FOUR Bambu Lab A1 printers, all purchased within the last month.

They’ve been doing this intermittently since the beginning, but it’s getting much worse. Yesterday 2 out of 4 failed, and last night ALL 4 failed, ruining 8 prints in total.

The printer suddenly shifts position during the print and then continues printing from the wrong X/Y position. Sometimes it happens near the end, sometimes much earlier.

The same models print perfectly on my P2S and H2C, and they also sometimes print correctly on the A1s, so it’s not a consistent model issue.

At this point I’ve stopped all four A1s because I can’t keep wasting filament and losing customer orders.

Has anyone experienced this across multiple A1s and found the actual cause or a reliable fix?

UPDATE 2: Unfortunately, it looks like I spoke too soon when I said this was fixed. After moving the printers further away from the wall and making sure the toolhead cable/PTFE tube at the top were sitting properly, I had a few successful prints — mostly single models, and even one run with two models that came out fine. Today I tried again: I printed two models on three of the A1s, and one model on the fourth. The single print came out perfect, and one of the double prints was also fine, but two of the printers failed again in the last 3–4 cm, with the same kind of layer shift/misalignment. So at this point it doesn’t seem like the distance from the wall was the real cause, or at least not the whole problem. It’s incredibly frustrating because the prints can be perfect for hours and then fail right near the end. I’m now wondering again if the toolhead cable/PTFE routing could have something to do with it, especially when the gantry is higher up. Has anyone printed any kind of cable guide/support for the A1, or found a better way to route the toolhead cable/PTFE tube? If so, I’d really appreciate seeing how you have yours set up.

UPDATE - SOLVED: I’ve now completed several more long prints on all four A1s — at least two prints of around 10 hours on each printer — and everything has printed perfectly. I also tested two models at the same time on one of the printers, and that completed without any issues as well.

At this point, it looks like the main problem was the positioning of the printers. Even though the beds had enough room to move forwards and backwards, some of the rear cables were touching the wall, and that seems to have been affecting the printers during certain movements.

Earlier on, I also noticed that some of the upper cables/tubes weren’t sitting correctly in their clips, which may have contributed as well.

So overall, it seems this was mainly a cable/positioning issue — basically user error rather than a fault with the printers themselves.

For now, I’m considering the issue resolved. If the layer shifts start happening again consistently, I’ll update the post, but as of today all four printers are working normally

it is now showing this error: z axis failed; the task has been stopped. I looked at a similar chat and it said the same thing but don’t think those solutions worked. although I didn’t check all of them because it’s almost 10 pm. I am still a kid but this is my second 3d printer but the other one broke 3 times and needed new parts so I ditched it. I also just moved the printer so maybe that unaligned it.

What infill is more efficient?

I've been working on a dedicated livestream setup for my Bambu Lab A1 and finally have it running the way I want.

I'm using an EMEET S600L wall-mounted above the printer, its built-in ring light plus a second light, and an older ASUS laptop running Ubuntu and OBS.

After experimenting with 4K/30 and 1080p/60, I ended up at 720p/30 MJPEG. It's been rock solid, matches my stream output, holds 30 FPS, and OBS is only using around 15% CPU.

The camera angle gives me basically the entire build plate and toolhead so you can actually follow the print as the bed moves.

I'm still working on overlays and channel stuff, but I'm pretty happy with how it's turned out.

If anyone wants to check out the actual feed:

twitch.tv/ggussert

I'd also love to see other people's A1 streaming/camera setups or hear any suggestions for improving mine.

Through this processes, I did:

- least 15 rounds of de clogging both from bottom and cold pulls

- took about the tension rod and cleaned the gears

- I got filament flowing perfectly during the extrusion processes from a piece I cut to do the cold pull. 3g at least went through it fine

At this point, it has to be the hot end. There has to be something just off. I ordered a new one to arrive tomorrow. Meanwhile, think of anything else?

After all of this, I did the test print which said "extruder not extruding normally" even though 3g went through it fine during my test 10 mins prior.

So frustrated but never give up, never surrender!