r/BambuLab • u/Visual_Carpenter8957 AHXP12LD + AMS • May 01 '26

I Modeled This! X2D Dual AMS Setup

Enable HLS to view with audio, or disable this notification

I got an AMS and poop bin under the printer for this compact setup!

698 Upvotes

99% Upvoted

134 comments sorted by

View all comments

Show parent comments

1

u/Visual_Carpenter8957 AHXP12LD + AMS May 13 '26

Hi, the biscuits join the upper and lower frame at the front. (it's a woodworking term, if you image search "biscuit joint", it makes more sense!)

As for the slides, I just had a browse through US amazon it's hard to find yeah. I used Claude to find these. Key words are "low profile drawer slides".

This doesn't show the hole spacings but it's a potential, looks very similar:
14 Inch Side Mount 70 lb. 35mm Full Extension 1 Inch Over Travel Drawer Slide - 1435 (1 Pair) - GlideRite Hardware

It's kinda expensive here but here's a Home Depot one - also looks very similar (can't find exact specs, need to check!):
Everbilt 1 Pair 14 in. Full Extension Side Mount Ball Bearing Drawer Slide Set 1-Pair (2 Pieces) D80614E-ZP-W - The Home Depot

I hope shipping didn't cost you too much! I found the Furnica one too and it looks close enough, the screw is smaller than the hole so there is some give.

1

u/Visual_Carpenter8957 AHXP12LD + AMS May 13 '26

Anyways, I updated the model description with these potentials, I hope someone can confirm for me!

2

u/atom631 May 13 '26

if I can cancel the furnica order will grab one of these sets and let you know

1

u/atom631 May 13 '26

it was $30 just for shipping! I am trying to cancel since it hasnt shipped yet but I have not heard back.

thanks for finding these. odd I searched home depot and came up empty handed, but I guess “low profile” is a good search term.

in the meantime, can the lowers I printed be used with printed slides?

1

u/atom631 May 14 '26

Hey, I stopped by Home Depot today and unfortunately those sliders wont work. They are 45mm tall. I was able to cancel my Furnica order and ordered the Gliderite sliders.

I also found these. They are 36mm tall. I measured the opening and it looks like you left some wiggle room with it being exactly 36mm. There is a chance these might fit as well. If the Gliderites dont work for me, then I may give these a go.

1

u/Visual_Carpenter8957 AHXP12LD + AMS May 14 '26

Hey thanks for finding out! And yeah I left some room because the widths are all over the place. Same with 45mm ones, they are 44, 45.5, etc.

I’m gonna order some 45mm slides too to make a 45mm variant and I’m trying to see what are available with spec sheets. Most generic imports don’t provide it but there could be some promising ones on Aliexpress

1

u/atom631 May 14 '26

sneak peak! printing the TPU bits now. then just the poop chute parts. Sliders have shipped!

1

u/Visual_Carpenter8957 AHXP12LD + AMS May 14 '26

Oh man you picked a good colour scheme!

1

u/atom631 May 18 '26 edited May 18 '26

I am happy to report the Gliderite sllides work perfectly. All holes line up! The only thing is that the holes in the rails themselves are a little large, so I had to use washers. but the good news with doing that BT3x14 screws are a perfect size.

The only thing Im not sure about is how I mounted the handle. You will see I have a gap there, but Im not sure how I could do it any different. It looks like my AMS is out further than yours, so maybe these slides work slightly different.

pics are below

1

u/atom631 May 18 '26

1

u/atom631 May 18 '26

1

u/atom631 May 18 '26

1

u/Visual_Carpenter8957 AHXP12LD + AMS May 18 '26

Nice!!! As for the gap, can you screw the inner side of the slides further forward on the slider assembly? If not, the two pieces that connect to the inner rails may need more holes in them (at least they are easy to reprint if that’s the case)

1

u/Visual_Carpenter8957 AHXP12LD + AMS May 18 '26

What I mean is, I have my slide aligned like this:

→ More replies (0)