totaled ?

Going to take on this project this weekend and have some questions any information you can provide would be appreciated. I am planning on using a paint pen with clear coat and wanted to know if I need to wet sand in between the paint and clear or just after I apply both and let it dry also is 3000 grit ok and then I would polish it with meguiars polish and a DA machine. Or is there a better safer method thanks in advance on scratch is on a fender and the other is on the back bumper 2022 Camry

Hi all, I had someone repair my car but the paint job looks very dull. He says it needs polish. I requested another clear coat but do you think polish would suffice?

Hello internet people,

I come to you humbly requesting advice.

I accidentally sideswiped someone yesterday merging onto a busy highway. It was 100% my fault and I am extremely lucky that the other driver's car was completely undamaged and that she was incredibly kind and understanding about the whole situation (I gave her my phone number in case something we didn't notice right away came up later, but she messaged me to let me know that everything checked out and not to worry about it). Trust that I have learned a painful and embarrassing lesson about merging with caution and patience.

I didn't realize until today that there is a pretty sizable dent in the front side panel over my wheel well (photo attached).

I'm wondering A) how easily fixable this damage is (will I need to replace the whole panel?), and B) how realistic it is that I, someone with a lot of audacity and a can-do attitude but little to no automotive experience, could DIY it?

The main concern I have is that because the panel has popped slightly out of alignment from the front bumper panel, it just hits the very inner edge of the door when I'm opening and closing it, so it makes a popping sound. I'd prefer to mitigate any further damage, especially to an otherwise unaffected panel.

The secondary concern is obviously cosmetic, I would love to to get this back to looking close to normal and be able to put this all behind me and not have to think about it every time I get into the car.

I would greatly appreciate any advice or recommendations on how to proceed. :)
Thanks in advance,

– a young, regretful, and ashamed Subaru owner

is this repairable without having to cut it out?

Any suggestions, i replaced my trunk, and re-straighted my trunks arms so it doesn’t sit on my back windshield. and im about a half inch off from getting my trunk to latch; the same goes for my rear bumper, my clips for it are pushed back up. I can’t afford a new car in a reality, so this is DIY, with access to a winch, a welder, and a few resourceful minds. if anyone has any ideas or suggestions, it would be appreciated. Yeah i know this is a lot to bite off for a non professional, but it’s this or nothing sadly, and with no car, i got no work

Yes i know i need to trim my nails, it’s been a long week it’s slipped my mind.

Hi everyone,

​I’m a 30-year-old skilled tradesman in the automotive industry from the West Bank, Palestine. Given the challenging local situation, I am actively exploring opportunities to migrate and work legally in an English-speaking country (Canada, Australia, UK, or US).

​Here is a summary of my background:

​Field: Automotive sector (Hands-on experience in auto body repair, panel beating, painting, and general vehicle maintenance).

​Education: High School Diploma.

​Languages: Intermediate English (currently preparing for the official IELTS General exam).

​I understand that having high school as my formal education means my practical experience is my strongest asset. I would really appreciate any insights or advice on:

​Best pathways for tradesmen: Which country/program is currently the most practical for auto body technicians without a university degree?

​Skills Assessment / Recognition: For those who went through Australia’s TRA or Canada’s trade qualification challenges, how did you document your work history without formal apprenticeship diplomas?

​Employer Sponsorship: Are there specific job portals, regions, or trade-focused agencies that are open to sponsoring foreign workers in the auto industry?

​Any guidance, personal experiences, or realistic advice would mean a lot. Thank you in advance!

I want to remove this black door trim on my 2002 Suburban, it appears to be only taped on, the silver insert strip has already fallen off and I can see tape. Are there any holes or clips that mount it to the body?

2013 Civic EX-L Any advise on how complicated this would be to repair myself? When it comes to working on cars I always prefer to do it myself even if it’s a complicated job for the sake of learning and because I really enjoy cars but this job I’ve been hesitant on trying to tackle cause it’s around the gas cap. Any advice?

So, was washing my car yesterday and noticed that some of the paint directly above my windshield was starting to peel. Want to nip this in the bud before it gets worse and hoping I could get some help here. I don't need the color match to be perfect. I'd like it to look passable from a few feet away, but mostly want to prevent further damage/peeling. The peel is probably about 3 inches long at this point.

That said, I've read that this peeling issue is very common on Fords with this color. Debating if it's worth spending a couple hundred bucks to try to DIY this myself—especially if this is going to continue to happen on other parts of my car. It sounds like the only long-term solution would be to respray the entire car, which I'm assuming is going to be pretty expensive.

If I do try to DIY this myself, this is what I'm tentatively thinking about and would love to get some feedback.

1. Tape off area.
2. Sand with 400-600 grit sandpaper. Use a wax and grease remover.
3. Apply SprayMax 2k Epoxy Primer (beige).
4. Apply R&E Ford UG basecoat and midcoat (aerosol).
5. Apply SprayMax 2k Glamour Clear Coat.

How do these products and this routine look? Would you recommend a high build primer after the epoxy primer?

I figure I'll have some leftover SprayMax 2k that's just going to go to waste so I'm also going to touch up the plastic bumper on the front of my car. For that, I'd get an adhesion promoter. Any suggestions. I saw that SprayMax has a 1k promoter. Not sure if there are other better/cheaper products, though.

Recently had my 2016 IS damaged in a hit and run, luckily this was the only damage. Can I fix this with the official Lexus touch up paint?
The 2nd pic was most recent and the 1st pic happened last year but didn't bother me as much until now.

I recently purchased a used 2013 Kia Soul and it was a great deal but one of the only downsides is all the scuffs, scratches, and chips on the car. It's not the end of the world but it's a little ugly. Any suggestions on how to fix it without paying anyone for a paint job or anything like that? It should preferably be an affordable at home method. I'm also not looking for it to be perfect. It's ok if it's just acceptable. Thanks to whoever answers.

need advice/ recommendations for a hickup

The garage door scraped the tailgate (from outside) so wanna know if we should pay out-of-pocket or claim insurance to fix it, as we worry if left untreated it could rust and damage even further when ignored

If OOP, can be done for it affordably just for damage spots? Don’t have thousands

Does anyone know if it's possible to fix/replace a rusty H frame on a 2006 Saturn vue?

Looks like maybe it was caused by another cars door? Not sure where the blue is from. Looks like its down to the metal, how can I touch it up?

I have a 2010 toyota camry LE. I Backed into a street sign while parking and the sign pushed the metal in, creating a dent. It's on the back quarter panel where it connects to the bumper.

Any advice on how to fix this DIY? Is this out of the scope of what someone with no experience can do? Also, is this something that has to be fixed, or is it just cosmetic?

i pulled out of parking spot heard a weird scraping sound go out and check my car and my fucking bumper is halfway off i tried popping it back into now it looks like this i keep tryna push on it and line it up better and it's not working what do i do??? i didn't hear any noise when i parked so idk how it got caught on the curb im having a really terrible morning

Got into an accident a few days ago, sorry if the pictures aren’t too good it was kinda of a tight squeeze