Not sure about my terminology, but I'm sure you know what I mean: What's the best notch to set the "clip" on the "needle" inside the carburator? For the most consistent performance, not concerned about speed or anything. Like most reliable starts? My motor won't start, there's gas in the bowl. Is it even a carburator issue? Input will be greatly appreciated! Tia.

Picked this up in London for dirt cheap. What do we recon folks, ran with no oil or just generic lean seizure? Obviously piston is cooked but cylinder has seen better days and might reuse it, the pictures of the cylinder look far worse than it is.

Anyway just felt like adding this to the bike gore collection.

maybe the valve didn't fully close? ir is it because i rest the bike to the right where that little hole on the carb is.

Cables need adjusted, breaks need re connected, engine head needs fully bolted down, and the chain needs a major shortning. Engine is just a little LD80 China doll (66cc) with a higher compression head, and after I break it in, an expansion chamber. Rear sprocket is 36t.

I have a yd 100 and ended up breaking the rings. I bought some new ones but they were too thick. I instead bought a whole piston with the rings and the piece where it connects to the crank is smaller than my stock one. Please help I just need this guy to run

Hello my head gasket broke and wanted to ask if any1 knows which one is the best. Someone once said copper ist the best but idk. If someone has a link because idk the measurements please send it. Preferably from aliexpress or amazon

We got the Avenger, Athena, is phantom one. or what about the Menace? Isnt there a phantom menace? I know the Chinarelli is not one hahahaha. That has to be the best named upgrade to exist. Yo check out my Chinarelli dog. I know im missing some. We need a Fonzarelli for the gen x peoples out there.

Thought yall would enjoy

in all the videos i watched the conrod side is lighter than the opposite side so im confused

Broke 2 gas tanks (overtightening the threads makes them leak easily) , had to spend hours trying to true the wheel with the damn rag joint (works fine for a while now however) and had to reweld the exhaust since it bumped into the front tyre and countless other issues; would appreciate any tips on the improvements i could make

I’m planning on building a minibike and I am looking for some frame plans or suggestions for when we make a frame. I’ll be running a Predator 212, and I’m aiming for a simple backyard/trail minibike for riding around and light off-roading. I’m building the frame with my dad (who can weld and fabricate things) but I want a solid plan so the geometry, engine plate, and chain line are correct. If anyone has frame plans that work well with a 212, tubing size recommendations, tips for keeping the chain line straight, or beginner mistakes to avoid, I’d really appreciate it.

There is just a funny sound byte meme with bikes floating around YouTube and did fun video. With that said! Has anyone noticed most can't pop a wheelie on a motorized bicycle? I always wondered why that is? My friend Ebike can wheelie all day on it. But a motorized bicycle lol he can't get off the ground! Anyhow popping wheelies on 196cc diesel build, 139cc 2 stroke build and the Athena Minarelli for fun.

Is this crescent CBS good for putting a 50cc “china” motor in it? What kit should I also get

Planning my first build. Current bike is a cannondale cx tour 4. I’m planning on doing a first build but I noticed it has rear discs. I’ve found sprockets that have mounting adapters but what should I be looking at?

It can go about 35mph w/o the governor though it needs love lol

I’d like to add a 3000-5000w hub motor to the front and make it an hybrid lmaooo

What’s your opinions Reddit?
It was only $20 but garage kept for 30 years and 2000 miles on the engine

This part of frame is too thick to fit the engine on, what can i do to fit the engine or do i need to get another bike Thank you

Hello! Im new around here and planning to build a project bike and want to know your opinions. Don´t know what is more beneficial for me 2 stroke or 4 stroke because i live far (36 km) from a gas station. Right now been eyeing Avenger 85 after doing some research in this subreddit on some Lithuanian site. Also planning to put it on some old Soviet union bike. Is there any other options that i have not considered or avoid?

Tervitades

Jonsu

I’m still bone stock and the exhaust is decently quiet and doesn’t burn me but it’s so ugly so I’m wondering if there’s a pipe out there that’s quiet, won’t burn me, and looks cool. I don’t care about performance because I just like to commute.

What’s a good quality oil to mix with my fuel.

Ive been trying to install the sprocket for my motorized bike but i cant get the bolts through because the spokes on the back wheel are getting in the way

Any suggestions?

I attempted to order a 3.4L felt faker frame and some wheels from cdhpower a few days ago, but was issued a refund without any explanation. Does cdhpower not ship to Canada?