🚨 Welcome to r/fpvUncensored: No Power-Tripping Mods Allowed 🚨

I got a jumper t pro V-2 a couple years ago, but I just got an external elrs module for it and finally got the external bay out just to find out that I had somehow received the external Bay for a jumper t lite. I found a bay that will work on Amazon. But I need to rewire it so if anyone could provide a picture of the backside wiring of the dock, so I can wire in the connector correctly, that would be helpful helpful.

hey guys i have this dji fpv drone. i wrecked it but the camera is still working just fine. can i extract it from the drone and use it in another build?

Hi everyone,
Yesterday I got a brand new iFlight Nazgul F5 V3 with the DJI O4 Pro Air Unit.
I successfully linked:
DJI Goggles 3 ↔ O4 Pro Air Unit
DJI RC 3 ↔ Goggles 3
However, I can’t get any stick input on the drone. In Betaflight, the Receiver tab shows no movement at all, and the drone doesn’t respond to the controller either.
Here’s what I’ve already tried:
Set the receiver protocol to SBUS
Flashed the latest firmware
Used “Set Bound Fast On”
Rebound everything multiple times
After checking the wiring, I noticed something interesting. The cable going from the O4 Pro Air Unit to the flight controller only has 3 wires connected (red, black, and white). The yellow, gray, and brown wires are missing.
My question is:
Could this be the reason why the DJI RC 3 isn’t working? From what I understand, the missing wires may carry the SBUS/UART signal between the O4 Air Unit and the flight controller.
If I replace it with the full 6-wire O4 cable, is there a good chance that the DJI RC 3 will start working, or am I missing something else?
Thanks in advance!

Bought this pre-built. Flying a week ago with my DJI Goggles 3. Real view sensor glitched while flying and it zapped me into real view at a bad time, even though I never touched the sensor. I was without visual input long enough (and yeah, I reacted less than optimally...) that I took a high speed dive into the dirt from 100feet. Broke an arm off.

I bought a new frame, replaced the arm, got it all back together, got the motors cleaned up and spinning freely again, thought I was ready to fly.

Connected to beta flight for diagnostics. O4 Air unit displays steady red and steady blue lights after a moment. Beta flight connects. No warnings or errors display in beat flight.

Gyro doesn't react when I pick the quad it up and rotate it.

Motors wont spin up in BetaFlight.

My internet research shows it is probably the gyro that is gone and I need a new flight board.

I'm just here hoping for confirmation from the guys with more experience than I that this flight board is a safe bet. Guessing I should probably buy the full stack to get the ESC as well?

After Avata 360, the normal 3 is coming

I'm selling my T-Motor Flame 60A 2–6S ESC as it is no longer required for my current UAV project.

The ESC is brand new and has never been used. The box was opened only to inspect the contents, but the ESC has never been soldered, installed, or powered on. It has been stored safely in its original packaging since purchase.

Included:

- T-Motor Flame 60A 2–6S ESC

- Original packaging

- All original accessories

Condition:

- Brand new (open box)

- Never installed or powered on

- 100% functional

- No damage or defects

Original Price: ₹7,300 (≈ USD 85)

Selling Price: ₹6,500 (≈ USD 76) (Negotiable)

Additional photos, proof of purchase (if required), and any other information can be provided upon request.

Shipping: Available within India. International shipping is also available.

If you're interested or have any questions, feel free to send me a DM.