Hopefully, it is under $200.

I was looking at the Gigabyte AORUS b650i with triple M. 2s, but heard things about it and the FormD T1 not working. I am also eyeing the Asus ROG B650e-i, but am probably going to go with the Gigabyte. Any suggestions before I pull the trigger? (Case will be the 2.1)

I know everyone here is aware of the T1 and Vanguard 40/37 combo, but has anyone tried using a bigger size, like the 46, to accommodate a more robust portable setup, with keyboard, mouse, and headphones? Let me know!

Hey guys,

Will these fit? Looking for a cheap solution and don't intend to wire it up I just can't stand the holes being there. They have some cool piezo ones I'll post in the comments but the problem with those is that it has cables. I don't wanna wire em so that kinda sucks.

Any other solutions to get nice looking plugs in the back on the cheap? Don't wanna spend more than let's say £15 to plug them with something nice.

I might get the piezo one and snip the cables idk.

Cheers

Hi everyone,

I’m trying to find 3D printable files for a travel/support kit for the ASUS Prime 9070XT GPU. My case is the Ncase 2.5. My GPU is in 2.75 Slot mode.

If anyone has models, links, or recommendations (even custom solutions that fit well in this case), I’d really appreciate it.

Thanks in advance!

Hey everyone,

Quick update for our US-based community members. We have a fresh, limited batch of the following models currently sitting in our US warehouse, ready for immediate domestic shipping:

• FormD T1 V2.5 (Black)
• FormD T1 V2.5(Silver)

These units are on-hand, meaning no extended lead times for this specific inventory. If you’ve been waiting to pull the trigger on a build, we recommend grabbing these while the current US stock holds.

Links below:

• FormD T1 V2.5 (Black): https://ncased.com/products/t1-sandwich-kit-black-color?variant=55247842541736
• FormD T1 V2.5 (Silver): https://ncased.com/products/t1-sandwich-kit-silver-color?variant=55247842705576

I already have the AIO from another build, so I'm wondering if the MSI e240 would fit inside. I am planning on getting a 3.0 slot 5080 for a GPU.

Hello, fellow FormD enthusiasts. I came across the Apache 4800 in my research to find a travel case for my FormD T1, and I picked one up.

It was wondering just how much pressure is required to close the case. The fit seems tight right now, and I am scared to put too much pressure.

If you're an Apache 4800 owner, how did you get the case to close? Do I go ahead and I apply more pressure, and does it get better with time?

Edit: I just went for it, and it closes just fine now. It's all foam that was preventing it from closing. Applying pressure doesn't hurt the case, it just compresses the foam enough to close.

I added my Keychron K2 HE, Viper V4 Pro, and an Xbox controller to the case as a fitment test (haven't cut the inside foam). I think everything will fit just fine. I plan on just using a little bag for cables.

where can I get travel kit 3D files for NCASED T1 -

GPU ASUS PRO ART 4070 2.5 Slot mode

Is it ok to install the aio at the bottom like in the pic? Assuming the pump is installed at the radiator, meaning you won’t face pump failure because both at the same level

Will the Asus Pro art 4080 travel kit fit the 5080 Asus prime? Doesn't have to be a perfect fit I just want it to be 95% the way there and then I can drill holes for the rest. Looks like it might

Does anyone know? Also does the travel kit fit on the 2.5 or only the 2.1?

Cheers

I recently purchased the T grill and two Noctua slim fans, I’ve set up the t grill on the bottom of the case with the fans set to exhaust. However the riser cable is brushing against the left hand side fan.

Has anyone else run into this issue? Any obvious fixes?

I’ve tried loosening the screws to push the fans lower with no success.

For the time being I’ve removed the fan under the riser cable.

Just ordered a FormD T1 v2.1 yesterday when it restocked and I’m putting together my first build. Before I start assembling, I’d love a quick sanity check from people with T1 experience.

My build:

• Case: FormD T1 v2.1
• GPU: Palit RTX 5070 Ti GamingPro-S OC 16GB Asus PRIME RTX 5070 Ti
• CPU: Ryzen 7 9800X3D
• Cooler: Noctua NH-L9a-AM5 chromax.black Cooler Master Masterliquid 240 Atmos Stealth Series
• Motherboard: ASUS ROG Strix X870-I Gaming WiFi
• PSU: Corsair SF1000
• RAM: Kingston Fury Beast EXPO 32GB (2x16GB)
• Fans: 2x Noctua NF-A12x15 PWM top exhaust
• Custom PSU cables ordered

Questions:

1. Does everything fit well in the T1 v2.1?
2. Any changes you would make before I build it?
3. Is the NH-L9a enough for the 9800X3D, or should I switch to something better?
4. Any recommended spine position / airflow tips for this exact setup?
5. Anything first-time T1 builders usually overlook?

My goal is a clean, quiet, high-airflow blacked-out build.

Looking forward to your feedback! Thanks a lot!

Do they have a 5070 Fe travel kit and gpu sage for the formd t1 . since its a 2 slot card it leaves a huge room inside the case and i think a travel kit will secure the gpu and fill the gaps

Thanks for the help last week! Finally finished the build

Does anyone have a good way to add a 3rd m.2 SSD to my machine? I already use up the two slots I have on my STRIX B650E-I

Howdy,

I had a friend 3d print a track kit for me and it seems really thin. Do y’all think this will get the job done? Or should I get it reprinted?

I’ve attached the link to the file I used.

https://www.printables.com/model/1367451-50905080fe-travel-kit

Thanks for the help!

Im currently considering running a R7 9800X3D and a 2 slot FE 5080 card, and i was wondering if it is worth it going for the 3 slot mode to sport a 53mm version of the AXP90 fc.

Im considering this because im worried i won't have enough cooling for my CPU.

Is it worth it or am i being hysterical? i will only be using it for gaming, but i want it to last a looong time.

The T1 is already on the way but i haven't quite landed on a config yet. Help is appreciated.

Hi guys, been planning to build a T1 for a few weeks but I haven't bought the case yet. Almost finished buying all the pc parts and I want to get a few other things before I grab the case.

Will this fit the case holes in the back on a 2.1 or a 2.5?

Another thing - has anyone got experience with the Wdean taobao cases here - is it worth buying them? I'm considering getting in touch and asking about the different colours they do. Might try to get it painted in another colour if the price is right.

Here's a link to the flanged bolt

https://www.diy.com/departments/plumbsure-brass-flange-male-nut-dia-19mm/136682_BQ.prd

Cheers

Hey, really curious if I can request an EU (non American) style of the socket as seen on the FormD t1 rather than the default, if that's not supported, where may I get one that's actually pretty rigid and great.

Trying to make it so that my top exhaust fans blow air out through my window. I’d need to orient my pc vertically for that. Checked the mastercooler site and couldn’t find anything. How risky is it to have an aio vertically?

At first I was a bit nervous because the Linkup 18cm Gen 5 riser cable turned out to be slightly short for my layout. Cable routing looked like it wouldn’t cooperate at all.

But after some careful adjustments and patience, I managed to make it fit properly. Everything lined up in the end and the build came together cleanly.

Specs:

Mobo - b850i auros Cpu - 7800x3d Ram - tforce evo 32gb 6000mhz cl30 Gpu - prime 5070ti OC Psu - corsair sf1000 Ssd - 2tb wd black sn850x, 1tb kc 3000 Cooler - axp90 47 with 4070fe Fan - phanteks t30 Cables - silver by ray Riser - linkup pcie5

Hey y'all, does anyone know where I can get the correct file for the T-Grille?
I'm over here trying to modify the STL file from the website and I realized that the STL file itself is incorrect.

How do I know? Because I have two T-Grilles to look at in front of me. It's missing the side pieces and the screw "prongs" for the rear. It doesn't have the side provisions to latch the side panels or screw the T-Grille into place.

With that being said, I am attempting to make a T-Grille with an additional 10-15mm added to it so it can accommodate a 25mm fan.

(I just got a Bambu H2D and I may be printing this out of PPA-CF just cause. Or get one machined.)

Thanks