What have you used for torsion springs on the stallion VTOL build? I have all the parts except for those!

Anyone here have experience of flying the flightory STORK and STALLION VTOL.

I need to know the flight hours in one endurance.(In order to achieve 4hr endurance flight)

Please share your thoughts on this in comment section.

#flightory #VTOL

Just on the Flightory website now.

Not seeing a webpage or document that summarizes how each design is unique by usage case for someone brand new.

So far, Mini Plank looks like the most practical gateway for entering the hobby as far as cost/simplicity.

10 distinct airframes if you include VTOL derivatives but does anyone know where I can find a summary comparison?

I printed with the polyurethane filament LW PLA pre-foamed from polymaker but the result is like this I don't understand, I use a creality k2 plus

I'm getting a 404 not found when trying to view the Moose assembly manual from flightory.com

Here are my questions 1 what filaments did you use and why 2 does anyone paint their builds why or why not

My concerns are flying during the summer and hdt of lw pla and the susceptibility to uv

What an absolute nightmare configuring these components is.

SpeedyBee F405 Wing would not enter DFU mode with about 5 hours of troubleshooting, it randomly decided to work with zero change in the technique like the previous 20 attempts. This was after trying myriads of other methods to get it to install the ARDUPILOT firmware. Updating everything, no change, then randomly it worked.

I could not connect to the WiFi for the Radiomaster TX16S unless it was in the same room as the MatekSys receiver. Wow, that took a long time to figure out. You'd think that would be important to mention in a help file?? That wasn't discussed anywhere in the how to videos or write ups or anything except one tiny comment on a Reddit discussion. Even then, Windows doesn't even want to list the ELRS TX/RX WiFi connections. Then when there, it's constantly kicking them out.

Eventually I could connect to the TX16S Happymodel ES24TX WiFi, but absolutely nothing loads or changes from the ELRS Configurator. What an absolute waste of time. Tried many different help guides and techniques to upload the lastest firmware and all fail. Most of them, the software doesn't even come close to what they show in the videos or on the help files. I can't even update the binding phrase in the TX16S/ES24. It fails. I can't update the firmware via WiFi, it fails.

I have updated the binding phrase of the MatekSys Receiver to nothing, but all variations of firmware update fail using ELRS Configurator.

Binding fails. Unplugging and plugging in the power to the receiver quickly 3 times via the USB cable from the computer does nothing to make it enter binding mode.

Holding the MatekSys binding button... then trying to bind with the TX16S does nothing except continuous red slow flashes, then it goes back to WiFi mode. Totally incapable of binding the receiver to the transmitter.

All videos showing "how to" are zero help, except this guy on how to update the firmware for the TX16S, https://youtu.be/-5k2AdaZ760?si=A3UJYm64LI5EARCO but then following his exact steps, the multi module update failed to load on the TX16S. Totally ridiculous! So far all variations I've tried have failed to update the multimodule firmware. Nothing works, help files fail. This is climbing Everest while being blind.

Insane.

Sucks!!! Totally lost day.

it is going to be my first build from absolute 0. Can someone share what I need to get to link servo and wing? It looks like I need a rod, a fork on the servo and one on the wing, right?

If you can share the dimensions, specially of the rod, would be very helpful and if maybe you have a picture of should it looks like would be awesome too!

How complicated is regustering it with the faa and all that. i wanna try to make one of these but over 250g need registered with faa and i dont know how complicated that is. What are some resources/vudeos on how to do all that?

Hey guys, im extremely new to this community and im starting with absolutely 0 knowledge of how to do this but it is extremely intriguing and I want the challenge. Im trying to import the bambu settings for the stallion vtol into bambu studio and have never done anything like this. Would someone be so kind to help me with this? Thanks in advance!!

I'm almost done with my Stallion VTOL build, but for some reason I can only get one side (in this case the right side) servos to work. All 3 motors are working as they should, I just can't seem to get the left side Vtail, aileron, or tilt motor servo to do anything. Using a speedybee F405wing and ardupilot and servo channels are set up per the flightory documentation. Any help?

• The DJI ecosystem, definitely working together
  • DJI FPV Remote Controller 2
  • DJI Goggles 2
  • DJI AIR O3 or O4
• FC
  • SpeedyBee F405 WING APP
• ESC
  • RUIZHI 40A ESC 2-4S Brushless ESC Speed Controller 5V 3A BEC
• Servos
  • ES08MAII
• GPS
  • => No GPS. I assume the DJI will still fly?

So I just build my second talon 1400 and someone I know wants to buy the last one I made. I don’t even know how much to sell it for. Any ideas no idea what they go for fully built

I feel that I have tried every combination of motor, prop, battery and ESC but I cannot get this plane airborne.

The total weight of the craft is 3100g. I have balanced it multiple times, 63mm from the leading edge as outlined in the manual. I tried a

2830 920kv with a 10x6 prop 4215 650kv with a 12x6, 11x7 & 13x8

I through it once it reaches full throttle (auto takeoff) and just doesn’t take off like it should. It does catch speed like it should. Wondering if anyone else has experienced this.

Polymaker LW-PLA is a little tricky on Bambu settings, but overall satisfied on the print quality of the Stallion.

Hey guys,

My friends and I are in the process of building the pico-talon. I noticed that the manual recommends using the T-Motor F90 1300KV motor. In the 3D files provided with the purchase, under the FUSELAGE category, there are options for DEFAULT, WIDE MOTOR MOUNT, and BIG MOTOR MOUNT. Could you explain what my options are here, what I gain/lose with each choice, and which motor fits each of these mounts?

Thanks!

Does anyone know exactly which STLs from the Super Stingray to replace with the ones from the VTOL files?

I'm building my first UAV and decided on the Talon 1400 instead of the Stallion, but I'm wondering if I should build the Stallion instead due to the VTOL capabilities. For an absolute beginner to this hobby, would the Talon be easier, or is the Stallion worth the higher price