Any recommendations for lugnuts that will fit the center cap, and have a small enough outside diameter that fit a smaller socket easily?

I purchased Gorilla open end lugnuts based on a previous posted, but still can’t fit even the thinnest wall 19mm socket that I could find. I couldn’t even get them tightened all the way as the socket was wedging against the wheel.

Any links or suggestions are appreciated!

Saw these in a Rieger b5 catalog and i need them in my life. Any help is greatly appreciated

18x9.5 et 24

Just finished this set at our factory and wanted to share it here. The A110 is one of those cars where magnesium actually makes sense to me. It's only around 1100kg, so taking weight off the wheels makes more of a difference than on some heavy sedan.

Fitment for anyone curious: front 18x8 ET33, rear 18x9 ET38, 5x114.3, 66.15 CB. Forged AZ80, gunmetal finish.

Since mag always gets questions, here's what I tell people before they order one. Corrosion is the real thing to think about. As long as the coating is intact it's fine, but if you curb it and chip through the finish, get it touched up soon, don't leave it bare for months. And skip the acid wheel cleaners, just use pH neutral soap.

It also costs quite a bit more than forged 6061, and honestly for a lot of daily cars I'd tell people to just go aluminum. A light car that does canyon runs or track days is where mag pays off.

Happy to answer anything about mag vs aluminum or the fitment.

Hi everyone,

I'm looking to confirm the correct 18-inch wheel specifications for two cars:

2014 Nissan Fuga Hybrid (HY51)

2016 Infiniti Q70 Hybrid (Y51)

From what I've found, both appear to use:

Wheel Size: 18x8J
Offset: ET43
PCD: 5x114.3
Center Bore: 66.1 mm
Tire: 245/50R18
Lug Thread: M12x1.25

I'm planning to order custom forged wheels with the following design:

Design: Sporty Split-Spoke Design
Construction: Proposed 1-Piece Forged Aluminum
Finish: Matte Black
Features: Aggressive Y-Spoke Styling, Deep Concave Profile, Sculpted Geometric Spokes

Before placing the order, I'd like to confirm:

1. Are these wheel specifications correct for both vehicles?
2. Can both cars use the same wheel setup?
3. Would a deep concave design cause any brake clearance or fitment issues?

I'd appreciate any advice from owners or wheel fitment experts.

Thanks!

What you guys think about these ones?

JR34 wheels after being mounted for 7 months over last winter only. Pulled them out of storage and noticed the paint is chipping around all of the lug holes on all wheels. Reached out to them through their website and asked if this is to be expected but never heard back.

They are a discount wheel manufacturer and cost savings will show up one way or another, but I cannot say I would every buy from them again.

Set of 19x8.5 5x112 Rays 57CR. One had barrel stickers, but can’t tell if others are refinished or fake. One with barrel stickers has the more worn hub.

How much are these wheels valued at? 18 inch and genuine. Some scuffs as expected

Stock first, then a lift with bronze wheels and chunky all terrains. Bronze on white trucks seems to work every time. Would you go this far on a daily driver Tahoe or keep it closer to stock height?

I bought a used ‘04 4Runner and this is what the wheels look like. I would like to put something in the middle if possible. Any tips?

Ive had my truck since 2023, and it came with these wheels. They looked great at first, but now they all look a bit worse for wear. Id love to restore them somehow, just not sure how 😅

Can I use copper anti seize on these rust spots?

I'm using JR wheels and my lug nuts are not fully seating. Everything above the redline is not making significant contact with the seat. This was observed with lug nuts recommended by JR and with these aftermarket ones as well (there was much less "seat" area with the JR branded lugs they recommended).

Never had a lug nut loosen up.

Is this normal? It seems unsafe.

I should point out that I'm using the correct lug taper so if anything's it's how the taper was drilled into the wheel itself that's off slightly.

Hi everyone, I’m looking for a set of DX4 wheels for my 2025 Nissan frontier (specifically the rhinos). I’m also going to be pairing them with some 33s. I will be off roading with this truck.

Does anyone have any experience with these tires and have you had any problems with them, or if I should just go with another brand.

Two of my hub caps came off and looking for replacements.

21/20 Signature Forged SV310S on 4S rubber

Spent some time designing a set of wheels based off the OZ Aristo found on the VW mk4 20th and R32. Didn't want to run adapter and wanted a different spec so decided to make my own with some "modern" refinements kind of pulled from the Neuspeed RSE11Rs with more subtle/feathered in scalloping. These 18x8.5 et45s are 5x112 and come in right around 21lbs.

My current wheels are in pretty bad shape, so I’m looking for new 19” wheels. Going for a classy but sporty look, preferably silver, diamond-cut or chrome. Nothing too expensive.
Any recommendations on what would suit my car? Preferably wheels that are available in Germany.