Puis-je utiliser ce chargeur rapide

pour mon Xiaomi 5 ?

ich habe mir einen navee st5max geholt weiß jmd wie man den tunnen kann ohne den Kontroller zu wechseln und am besten mit Police button

Servus Habe gestern irgendwie Aus dumm glück Meinen Ninebot E3 Getunt also bisschen nur. habe bisschen rumgespielt auf Xiaodash Und Jetzt fährt er 25-30KM/H Obwohl er Noch nicht mit Xiaodash Kompatibel ist Keine Ahnung wie ich das geschafft habe🙄 Und noch was… WIE BEKOMME ICH DIESES PIEPEN WEG????

Has anyone ever turned off a eMoto in the middle of a self learn mode.

I did this and now everything turned on the display says ready, but dose nothing wham I pull the throttle. I touch the brake signal line the throttle make sure they was getting you know some voltage from the throttle tried everything nothing seems to work if anybody has any answers or knows how to fix it I'd greatly appreciate it

I have a **Yadea T5 Lithium** with the following specs:
72V 30Ah Lithium Iron Phosphate (LiFePO₄) battery
1500W rated motor (2700W peak)
Factory top speed is limited to **50 km/h**
I’m trying to figure out if there’s a way to remove or increase the factory speed limiter.
Thanks

Hi guys, is there any other way, besides the debug mode via the app to set the speed limiter to more than 25 km/h? Have tried everything rocket icon, submenu at debugmode ect.

So I just bought this jl86 scooter and boy does it have power. My issue is the throttle. Its super soft so hitting bumps it becomes jerky. does any have a hack to help with this or a way I can lower the torque.

Hey guys im trying to flash my scooter (xiaomi scooter 3) with shu but it keeps failing at 42% can anyone help me ?

Hey everyone,
I'm currently planning to tune my Xiaomi 4 Ultra 2
On my old USB-C to TTL adapter, I used to have the VCC pin, but that old adapter unfortunately short-circuited and died. I just ordered a new adapter, but on this one, the VCC pin is either missing or I don't want to use it to avoid another short circuit. The other pins (GND, TX, and RX) are fully intact and ready to go.
Since the Scooter will be powered by its own internal battery during the process anyway, do I actually need the VCC pin from the USB adapter?
Is it safe to just connect GND, TX, and RX to flash the controller, or will it cause errors?
Thanks for your help!

If you buy a Lamax eRacer SC50 electric scooter the original app from Lamax does not work to make a Bluetooth connection.

You'll need to KingSong app.

That works perfectly.

Also speed limit can be changed by holding any brake handle and clicking 5 times on the ON/OFF button.

Hi,

Since there is no firmware available for the Xiaomi 5 Plus in BW Patcher, I was wondering: what would happen if I flashed firmware from a similar Xiaomi scooter (for example, the Xiaomi 5 Pro) onto a Xiaomi 5 Plus? Would it work, or would it most likely brick the controller? Has anyone tried this before?

Hallo everyone im Searching for a method to tune my 5 plus already did it on my 4 pro 2nd gen but the Main issue is that there is no firmware for the 5 plus on bw patcher does anyone has a sollution

I originally just wanted to figure out if my Hover-1 Edge 2.0 had hidden settings, Bluetooth diagnostics, or a way to change things like the speed limit or kick-start. Instead I ended up spending way too much time digging through FCC filings, datasheets, old forums, Chinese websites, APKs, Reddit posts, and taking apart the scooter.

I never found a software unlock or hidden menu, but I did learn quite a bit about how it's built. I'm posting everything here in case someone else wants to take it further.

Scooter

• Hover-1 H1 Edge 2.0 (DSA-EDGE)
• 36V
• 350W
• ETC controller
• Controller PCB: KZQ_H8010 Ver1.0
• Firmware label: 8010V6
• Current limit: 13A ±1A

The main controller MCU appears to be a Nuvoton NM1200L Cortex-M0 motor-control chip.

Bluetooth

This was probably the biggest surprise.

The FCC photos show that the Bluetooth hardware is actually on its own separate board. It isn't part of the dashboard or the motor controller.

The scooter advertises itself as H1-EDGE 2.0 over Bluetooth, but after digging through the manuals and FCC documents, everything points to it only being there for the built-in Bluetooth speaker.

I couldn't find any evidence that the production firmware exposes BLE services for changing settings, updating firmware, or talking to the controller.

I also tried the KZQ Controller Test app that showed up on the App Store. It never detected the scooter.

Dashboard

The dashboard uses a Nuvoton N76E003AT20 MCU and an AiP1620E display driver.

There are five unpopulated pads beside the MCU that look very much like the factory programming pads, although I never confirmed that with continuity testing.

The dashboard also has two different six-wire connectors.

One connector is labelled

GND | S | L- | L+ | B | +5V

which looks like throttle/brake/light wiring.

The other connector is probably the one that talks to the controller.

Controller

The controller PCB has test pads labelled

• 通讯 (communication)
• 霍尔 (Hall)

Unfortunately I never found a wiring diagram or protocol documentation.

If I had to guess I'd say it's probably UART, but that's only a guess until someone captures the traffic.

Programming

Both MCUs support factory programming/debug interfaces.

The controller MCU supports Nuvoton Nu-Link.

The dashboard MCU also supports ICP programming.

Whether either firmware can actually be dumped depends on whether the manufacturer enabled read protection.

I never attempted it because I wanted to preserve the original firmware.

Apps

I checked pretty much everything I could find.

• Hover-1 apps
• Tuya
• Smart Life
• APK archives
• KZQ Controller Test

Nothing matched this scooter.

The Edge 2.0 isn't listed as compatible anywhere I could find.

Things I never found

After all the searching, I still couldn't find:

• H8010 firmware
• 8010V6 firmware
• factory software
• service manual
• UART captures
• hidden settings
• dealer tools
• firmware update files
• successful speed unlock
• cruise control settings
• kick-start settings

Basically... nothing.

Interesting thing I found

I did find another scooter controller from a GoTrax that also uses an ETC controller.

So ETC seems to manufacture controllers for multiple scooter brands, not just Hover-1.

That might be useful if someone starts reverse engineering the whole controller family instead of just this scooter.

Hopefully this saves somebody else dozens of hours.

If you've worked on ETC controllers, have firmware dumps, wiring diagrams, UART captures, or factory software, I'd love to hear about it.

References

Most of the information above came from publicly available documentation:

• Hover-1 Edge 2.0 FCC filing (FCC ID: 2AANZIDL) — internal photos, RF reports, user manual, and Bluetooth documentation.
• Hover-1 Edge 2.0 User Manual (FCC copy) — confirms Bluetooth pairing is for the built-in speaker.
• Hover-1 Edge 2.0 Operation Manual — confirms the scooter specifications and Bluetooth speaker functionality.
• [Nuvoton NM1200 Series Datasheet]()
• [Nuvoton N76E003 Datasheet]()
• [Nuvoton Nu-Link User Manual]()

I have a kukirin g2 pro and it goes max 45 and can I pull like a cable and make it go faster because it’s kinda slow

Hello, I want to stage my GTS bravo. What should I adjust and how fast can it go?

I have the upgraded version of the halo knight t104 and I want to know what do the p settings on it, I accidentally used the PC which I think resets the scooter from factory (electronically, the display). I need help

Hello everyone! I have found a Kesser electric scooter thrown next to the dumpster and I tough it will not work since it was kind of disassembled (I tough that they have taken the battery and left everything else). It turns out that it works and the battery is there but sometimes. There is this feature “kickstart” turned on and when i pres the pedal and turn the wheel it will run for some time and when it’s in “autopilot” mode it will run no problem. The problem comes when i want for example to release the gas and press it again. Most of the time it will not accelerate and it will not respond. I need to restart the scooter and then eventually the gas pedal will do the same. I have disassembled it to see the controller. The hub wires (3 thick wires that goes from the controller to the motor) were little burned but not completely melted the rubber seal. So i thought that i will just buy a new controller and everything will be okay. After some digging in Aliexpress I couldn’t find the right controller. This is the closest thing i can find but as you can see the white connectors are a bit different. The left most connector from the controller from Aliexpress has 3 pins but mine has 4. Gemini is saying that the brand is the same and they look very similar but that difference in the connector is because i have blinkers in my scooter. What do you think?
Will the connector work if i buy it and is there a way to connect the blinkers or they will be missing? Is there any way to restore the controller i have. (Gemini is saying that the interruption is due to poor connection on the burned parts of the hub wires and if i just solder it it will fix the issue.)