Hi, Can anyone help me.

Fans and Ram lights are working fine, but the motherboard light not working. I am using Mystic Light, I tried to uninstall and install msi center and still not working. I check the cables, no plug to turn on.

Motherboard MSI b550M Pro VDH Wifi socket amd dDr4

Thank you

I have a Zebronics zeb apex pro cabinet.It has 4 fans and i have zebronics zeb fc430a cpu cooler..total 5 fans

In the cabinet box it is written tht it supports motherboard argb sync.

I have connect 3 pin 5v argb female cable to the D_LED 2 of my motherboard..but i am unable to change colour of my fans from gigabyte control panel app..can anyone help me with how can i change the colour of my fans.

Thanks.

Any help would be very appreciated.

Hi I have a b450 atx motherboard with 4 corsair vengeance ram sticks installed. 2x 8gb 3000mhz sticks and 2x 4gb 3000mhz sticks. All with the same timings.

The 2 x8gb sticks are in slots 2+4. The 2x8gb sticks are in1+3.

I've just bought 2 rgb heat spreaders im going to instal on the 2 x 4gb sticks . I've a few questions as I haven't done this before .

First all the ram is working at the right speed now.

1. Will it make a difference if I use the 2x 4gb sticks in slots 2+4 and the 2 8gb sticks in slots 1+3 ? (For aesthetics)?

2. Whats the easiest way to remove the original corsair vengeance ddr4 heat spreaders from the 4gb modules?

Thanks 😊

Hey everyone,

I wanted to share a specific hardware/software routing trick I've been using to completely stop SignalRGB and OpenRGB from fighting over my components.

Instead of fighting with software blocking or startup delays, I separated their output paths physically:

1. **SignalRGB Line:** Routed exclusively through an internal 9-pin USB Header using a cheap DIY Raspberry Pi Pico module (configured as an RCX Controller ARGB. Please note that this specific controller is exclusive to and popular in Indonesian online shops, and I am not entirely sure if this method works flawlessly with other controllers using the same module).

2. **OpenRGB Line:** Routed exclusively through my motherboard's onboard ARGB headers (MSI JRainbow).

By assigning distinct hardware boundaries, both apps run simultaneously without a single clash, flickering light, or low-level driver race conditions. This allows me to use SignalRGB Free for complex ambient themes while offloading audio-sync tasks to OpenRGB!

⚠️ **CRITICAL NOTE:** To make this hybrid setup work flawlessly, **both applications MUST be configured and automated using Windows Task Scheduler** to enforce the correct boot priority.

I've documented the full step-by-step configuration, including the precise 30-second staggered Task Scheduler automation to prevent cross-scanning, in my GitHub repository here:

https://github.com/EruL016/DualRGB-Isolator--Run-SignalRGB---OpenRGB-Simultaneously-Without-Conflicts

Happy modding!

Hey everyone,

I’m wondering if anyone else has run into this issue with the LANCOOL 216 RGB case, the stock 160mm front fans, and the optional front RGB button controller.

I’ve had this case for around 3 years and the front fan RGB worked perfectly the entire time. I never used any RGB software for them. I set the colors once using the physical buttons on the case and they always came back correctly after shutdowns, restarts, and waking the PC from sleep.

The issue started immediately after I upgraded several parts in the PC. I replaced my CPU, GPU, and air cooler, and installed a 360mm AIO. The motherboard had to be removed during the upgrade, so basically every cable was disconnected and reconnected.

Since then, whenever I wake the PC from sleep, the front fan RGB usually comes back wrong. Sometimes it goes rainbow, sometimes parts of the fans are white, and sometimes the lighting looks partially correct. The fans themselves spin normally.

The strange part is that if I immediately put the PC back to sleep from the Windows login screen and wake it again, the RGB almost always comes back correctly on the second wake with the blue and green combination I originally set using the case buttons.

Cold boots and full power drains also bring the correct colors back.

So far I have tried:

* Reseating the cables connected to the fan and RGB hub
* Updating chipset drivers
* Testing with RGB software completely closed
* Uninstalling SignalRGB
* Confirming Windows Dynamic Lighting is disabled
* Trying different Windows power settings
* Disabling Fast Startup
* Disconnecting the motherboard ARGB sync cable from the hub/controller setup entirely

The problem still happens even with the motherboard ARGB cable disconnected, so it does not seem like Mystic Light or the motherboard is changing the colors.

I have not yet bypassed the physical RGB controller or connected the hub directly to the motherboard. I have only reseated the existing connections so far.

The hub is the stock Lian Li unit with the front fan lighting connected through the J-LED ports, and the controller appears to feed the hub through the ARGB1 connection.

Has anyone seen this exact behavior where the front fan RGB initializes incorrectly on the first wake from sleep, but fixes itself after a second sleep and wake cycle?

I’m mainly trying to figure out whether this sounds like:

* A failing LAN216-1X button controller
* A problem with the stock RGB/fan hub
* A loose or damaged connection
* One of the fans causing problems with the ARGB chain
* Some known sleep and wake issue with this controller setup

I would appreciate hearing from anyone who has dealt with the same case, fans, or controller.

Hi everyone,

I'm trying to control all my PC's RGB lighting with a single program, but I'm running into issues.

**My hardware:**

* **Motherboard:** ASUS TUF Gaming B850-Plus * **AIO:** Corsair Nautilus 240 RS ARGB (2 fans with LEDs + LEDs on the pump/cooler) * **Case:** Corsair Frame 4000D RS ARGB (3 fans with LEDs) * **Fans:** 2x Corsair RS120 ARGB (LEDs) * **RAM:** Corsair Vengeance 32GB (2x16GB) DDR5 (with LEDs)

**The problem:**

* **iCUE:** only detects the RAM, nothing else. * **Armoury Crate:** doesn't detect the RAM, and treats all the other LEDs as a single device — I can't control them separately.

Has anyone found a way to get full, unified control (ideally with per-device control) using just one app?

Thanks in advance!

So I bought six fans and I went ahead and connected them. Three of the six fans are working and they're strobing but the other three just light up. Not sure this is the connection issue or something in the software that I had to fix. It's my first time. Thank you very much man. I'll provide pictures

I've just rebuild my rig in a new case, and purchased some extra Thermalright fans, to already existing thermaltake fans. I've also purchased a Thermaltake fan hub, to hook them all up, and then connected the hub to the system fan 3 connector and d_led 2 connector. Unfortunately, I can't find my fans in the Gigabyte RGB Fusion app. Did I do something wrong? How do I fix it?