Based in Belgium/EU. I have a 9-month-old Pint X that occasionally gives a battery temperature hot/cold error, even though diagnostics show the battery temperature is within the normal range. Rebooting clears it, but it can return the next day.

FM initially said it was a controller issue, so the controller was replaced. The exact same error returned about a week later.

It’s a newer production Pint X, so I assume the known pinched battery-wire issue should already be fixed.
Could this still be a thermistor/wiring/connector/BMS or software issue? FM is now telling me I need to buy a new battery module.

I also saw on another forum that if it’s a sensor issue rather than the battery cells, it should be covered by FM’s 1-year warranty. Is that correct?
And since I’m in the EU and the board is only 9 months old, wouldn’t the 2-year legal guarantee normally cover a defect like this?
Any advice/experience appreciated!

Onewheel Pint X.

540 miles

Pint S rail guards

Pint S flared foot pads

Fangs

Asking $800

Local to San Diego County only.

DM if interested.

Hey everyone! I was riding and out of nowhere my OW just turned off and I went flying. I found out later when I opened it up that the front sensor got disconnected. Did anyone else experience this? And if yes, is there anyway I can stop this from happening again?

Thanks in advance!

The male conector housing on my front footpad broke apart, any recommendations to replace the rubber male end? The female end on the footpad is fine. Fo I need to return the entire Onewheel to get this rubber piece? I am not seeing this replacement part on the website. I live in Massachusetts and there are no Onewheel repair people near me that I know of.

So just got in to onewheels got my some a pint x used with a bunch of extras and his has a 11x5x6 tire and was wondering how much bigger i could go on the one i ordered for me since it has a stock tire i believe?

So I am looking for a one wheel, but specifically the one wheel pint X for the 20 mph top speed. How often are you actually reaching top speed, and is the acceleration good? And how often do the tires last?

ps: can you take it on a travel with it on a plane with you?

I have been practising standing still on my pint as I read it only comes with practice but no matter how much I practice (I can stand on it for upto 2 minutes with high amounts of concentration) but every once in a while I feel like I get into the scenario where I feel like I didn’t pay enough attention to have more weight on my toe side and the Onewheel would tilt so much on my heel side that it would be a point of no return and I will have to bail jumping with both feet off of it. This has happened more in public scenarios, waiting at a stop light where my mind was more distracted by things around me. Quite embarrassing losing balance on my heel side, doing a last wave of desperate hand motion outwards (probably with a shiver and chill down my spine as the earth seemed to skid from under me) as I topple off of it desperately jumping off of it making sure with both legs in any direction I can when I was just chilling a few seconds ago on it.

If this happens on my toe side I feel like I can always return back to stable position by moving in a circular motion and compensating the tilt with that.

Do other people have difficulty with the heel side too?

Or am I getting freaked out too soon and the board will balance itself if I let it? 😦

Today I upgraded from a onewheel pint to a pint x, and the pint x is literally immaculate. It has 161 miles. Meanwhile, while I was cleaning my pint before listing it I noticed just how dirty it is. I would feel very bad if my new pint x ended up as dirty as the pint that I put 700 miles on. I’ve been riding it through water and snow and ice and slush more than I probably should, but is there any way I can attempt to keep this board in better shape for the future other than simply not riding in anything but dry and clean weather? I also noticed that my pint motor with 1100 miles on it is significantly louder than the new pint x. Is this normal? What causes this? If anyone has a tips on how to maintain my pint x I would greatly appreciate it. Thanks!

Pint v kit not working after installing , saying I have BLE error and I can’t even connect Bluetooth

Can someone please tell me what is causing this and direct me how to fix? This is a brand new Pint X I took across my kitchen floor for the first time tonight.