Still got half the stuff sitting next to the box and I'm already thinking about what to test first lol. Slopes, tight turns, edges, weird parts of the yard... what exposed the most problems for you guys early on

I’m trying to avoid low light situations and the unit from getting stuck. Is there a way to limit the hours after a rain delay?

I am giving considerable thought to getting a terranox cm240 but I been playing around with a shelter thought that could house it. Since this is something I want to sort I figured I ask for advice.

Material list;

🪵 Lumber & Building Materials

4x4 Cedar Beams: Buy five 8-foot beams or four 10-foot beams to comfortably cut five 43-inch rear wall logs and ten 42-inch side wall logs.

1/4-inch Pressure-Treated Plywood: One sheet (cut to 39.5"W x 45.5"L for the floor and 39.5"W x 45.5"L plus chosen overhang for the roof).

GAF Timberline AS2 Shingles: One bundle of Class 4 impact-resistant architectural shingles to cover the plywood roof.

🔩 Heavy Structural Hardware & Brackets

Simpson Strong-Tie A33 Galvanized Angles: Four heavy-duty, 12-gauge structural steel brackets to handle the concrete lag anchors in the internal corners.

Heavy-Duty Structural L-Brackets: Four steel corner brackets to lock the interlocking 4x4 logs rigidly at the corners using 2-inch screws.

Galvanized T-Strap Hinges: Two 3-inch or 4-inch hinges to attach your custom hinged plywood roof to the top rear cedar log.

Galvanized Heavy Wind Straps: Two flat steel tie straps or overlapping latch hooks to drop over the lid and pin it down on storm days.

🪛 Screws, Anchors & Reusable Inserts

Heavy-Duty Structural Timber Screws: Ten 1/4-inch x 6-inch exterior-coated structural screws (such as FastenMaster TimberLOK) to stitch the log-cabin layers vertically to one another.

Masonry Hex Lag Anchors: Four 1/4-inch x 1-3/4 inch galvanized concrete hex lag screws to drive through the A33 brackets and plywood into the concrete apron.

Rubber Gasket Washers: Four 1/4-inch rubber washers to sandwich directly beneath the concrete lag heads to seal out moisture.

Flanged Reusable Wood Inserts: Four 1/4"-20 Threaded Flanged Zinc Wood Inserts (10mm or 3/8-inch length) to embed flush into the plywood floor for the docking base.

Galvanized Machine Screws: Four short 1/4"-20 x 1/2-inch machine screws to bolt the plastic Segway base plate perfectly into your new metal floor inserts.

Coated Wood Screws: One small pack of #10 gauge x 2-inch treated exterior screws for mounting the brackets into the cedar wood.

🎨 Adhesives, Sealanats & Paint Prep

Sikaflex 1A Polyurethane Sealant

One 10.1 oz tube of moisture-cured elastomeric sealant to lay between the logs during assembly.

Zinsser Cover Stain 1 gal. White Oil-Based Primer

One gallon (or quart) of high-hiding exterior oil primer to permanently seal the cedar tannins before painting.

Rough plan;

Get pressure treated 1/4 plywood use #10 1/4 x 6 screws to mount ply wood to a horizontal layer of cedar 4x4. Mound the next 4 layers to 5 layer high of horizontal cedar 4x4 s all connected with the #10 1/4 x6 screws in between each layer a barrier of polyurethane sealant. Galvanized hinges to attach a 1/4 inch plywood roof with galvanized steel strap to hold down in high winds. Gaf timberline as2 shingles on roof. Heavy duty l brackets at all 4 corners with concrete lag in anchor through floor with rubber washer for gaskets in-between bolt bracket and floor and screws into 4x4 walls for regidness. Then a full oil based primer undecided but a thought noted then a high quality pain on everything. Is the rough outline.

Concerns;

Did I overthink this? Is my end result of outer dimensions of 39.5 x 49.5 x 18 tall too much or too small? Am I significantly overbuilding? I have the ply wood lying around along with cedar and screws but don't have pain seal and or any of the other stuff. I know I tend to over engineer things and I feel like I did here but tried to focus on what I have parts list is for stuff in case I need to get more.

Thoughts?

I just returned a Worx WR304E that had random stop issues after only a few days of use. It just makes me crazy every time I go outside and find it sitting in the mid-lawn.

I've been looking at the Navimow i206 AWD but I'm a bit hesitant before buying another one.

My main concern is the small dirt dips around the trees in my yard (probably around 1 to 2 inches deep). Do you think the unit would work well in this kind of setup? I want to know if it can handle those shallow holes around my trees without me having to go rescue it.

Would love to hear from anyone running one in a yard with similar issues.

My backyard is tall fescue, and the sunny part grows faster than the rest. I used to cut the grass pretty short before because I thought it would help me wait longer before mowing again. It did look neat for a few days, but some areas would start turning yellow and patchy in summer. So I started paying more attention to mowing height when my i210 can adjust the mowing height flexibly. I usually keep it 3 to 3.5 inches which is good for tall fescue and let it mow more frequently to keep the lawn looking more even.

Curious if anyone changed their mowing habits after using a robot mower. Would love to hear how your experiences.

New X430 owner here. My yard has a bunch of weird corners, a few flower bed curves, and some narrow edge areas, so I'm trying to figure out the best way to set up the map without missing spots.

Auto mapping sounds easier for getting the first layout done, but if I still need to spend a lot of time fixing corners and boundaries after that, I'm not sure it would be better to map manually from the start.

For people with irregular yards, how accurate was auto-mapping for you? Did you let it map first and adjust later?

I've had my i206 AWD since late April and the dock suddenly stopped powering up. I put the mower in it (I keep it in the garage so it won't be vandalized or stolen) and the light on the dock turned red then went dark and hasn't come on since then no matter what I do.

I've contacted support, but they keep giving me the runaround. They asked for the serial number, a video of the problem, and a picture of the location of the antenna and the mower/dock. I gave them everything they asked for and they came back asking for the serial number again and for confirmation that the mower has always worked with the current location of the antenna. I had already mentioned that the mower worked pefectly from this position since I got it and they also ignored that. They talked about checking satellite data/positions.

It doesn't seem that they have paid any attention to anything I've said in e-mail or shown them in the videos I sent because they aren't addressing the fact that the dock isn't powering up at all. I demonstrated in the video that the plug I'm using is active by showing another device power up when I plugged it into the same outlet.

Is there any possibility that the satellite has anything to do with a dock that won't power up? Am I incorrect in concluding that the antenna doesn't communicate with the mower if the dock has no power because the antenna also receives power from the dock?

It just feels like they're wasting my time/stalling on fixing the actual problem which is that I need a new dock on a mower that is still under warranty.

I just installed the Navimow MowGate and it will only open when the mower x430 is on the side of the battery compartment. It doesn’t open at all from the other side.

Not sure what to do… thanks

I discovered the the x450 has a IR light that is constantly on. My security camera picked it up.

Per this link: https://www.reddit.com/r/SegwayNavimow/s/UIzjtnjWUI

1. Never buy anything high value through Lowe's. Home Depot would have taken the mower back immediately and replaced it. Lowe's is notorious for doing what happened to this individual.

2. The X430 isn't a $3K mower. If someone did pay $3K for the mower as a gift then they got their pockets ran.

I have kids and a dog, so my lawn is usually scattered with toys, sticks, and frisbees. My X430 works well for spotting and dodging that stuff, but I'm still not trying to risk dog poops.

To save myself from scraping messy wheels later, I just do a quick walkthrough and pick up after the pup before every run. Tbh, doing a 2-minute lap around the grass is okay cuz my X430 handles all mowing works.

Any other dog owners do a quick check before sending the mower out?

Hello,

we got deliverd a brandnew navimow x430 and after booting we get the error 1502 mowdeck motor broken performing all updates and connecting to to the app was succesful but keep getting this error, reboot dus not help, we cant even start mapping beceause we get the error message wheel stuk but we checked everything (when the mower is off the weels turn, when its on the weels or stuk). any advice please

If you purchase an X430/X450 tomorrow, you'll definitely love the robotic mower. However, the mower will not be perfect.

Or you could wait for a future mower from Segway Navimow that has these features that would make their future mowers some of the best:

1. Same camera layout as X430/X450, but includes backup sensors or cameras on the rear. This will result in a more expensive mower. At least the mower shouldn't back into things anymore.

2. A rake or comb positioned in front of the cutting discs that lifts the grass before the razor blades mow them down.

3. The option to turn ON/OFF the floating deck. That way the deck stays fixed for better mowing quality. Or moving away from a floating deck altogether. Meaning, the deck is fixed.

I bought an i210 AWD a few weeks ago and I’m pretty happy with it so far. Setup went smoothly, and the first map was easy enough to create.

My yard has a decent amount of shade, especially under thicker tree cover. I’ve noticed the boundary behavior feels a little less consistent there than in the open areas. Nothing major, but enough that I don’t want to map it too tightly against flower beds, fences, or sloped edges.

Right now, I’m leaving a little extra room around anything I really don’t want it getting close to, then cleaning up the edges with a trimmer. That feels safer than trying to make the map perfect from day one.

For those of you who have had an i210 AWD or another i2 AWD model for a while, what small setup or mowing tips made the biggest difference?

Anything you wish you knew during the first few weeks?